Power Measurement Sanity Check

Our current SSD test suite is almost completely automated. There are only about a dozen points where manual intervention is required to go from plugging in the drive to having a directory full of graphs ready to be analyzed and uploaded for the review. This helps ensure the tests are highly repeatable, and makes it easier to run a drive through the 24+ hours of testing without losing too much sleep. But things can still occasionally go wrong, and that's what I assumed had happened when I first looked at the test results for the SK hynix Gold P31. The power efficiency scores were way out of the normal range for high-end NVMe drives, and I worried that something was amiss with our very fancy and expensive Quarch HD Programmable Power Module (PPM).

After completing the initial round of testing for the P31, I took several steps to validate the surprising results. First, checking that the PPM wasn't reporting any error codes, and that the graphs were generated from the right data (rather than something like plotting measurements from the 12V supply rail for a 3.3V-only M.2 drive). Then, verifying that the PPM still produced reasonable results for a drive we've previously tested, because we've been using this instrument since April 2019 without any recalibration. I put the Samsung 970 EVO Plus 1TB back on the testbed and re-ran some idle and load power measurements, which produced virtually identical results to our original measurements—confirming that the PPM is still accurately reporting instantaneous power draw.

At this point, it was looking pretty certain that the record-setting efficiency scores from the Gold P31 were genuine, but there were still a few semi-plausible failure modes that could have affected at least some of the tests. For example, on the ATSB tests we report the total Watt-hours of energy used by the drive over the course of the test. If the power log was truncated before the test finished, that could quite easily lead to a much lower total energy usage number—but the power log for The Destroyer contained a normal 7h20m of data (and most of our scripts to process the logs and generate graphs try to detect a truncated log).

To make sure there wasn't anything really strange going on behind the scenes, I re-ran all of the Linux-based synthetic benchmarks with the Quarch Power Studio application open and graphing the power measurements in realtime:

Ignoring the labels on the vertical axis, this all looks as expected. The different phases of the tests are very distinct, with the drive dropping down to reasonable idle power levels between phases, and load power steadily increasing with queue depth. The tests that involve writing data show that the drive's power consumption jumps up after the host system is finished writing, when the SSD flushes the SLC cache in the background. (Our current synthetic tests don't directly measure this phenomenon, but it's typical behavior.) But even so, the largest spikes visible at this scale (samples averaged into 131ms chunks) only hit 4W. It was at this point that I started pressing SK hynix for more details about the controller and NAND used in the P31, to see how they pulled off such impressive efficiency:

Sustained IO Performance
Random Read Random Write Mixed Random I/O
Sequential Read Sequential Write Mixed Sequential I/O

 

Power Management Features

Real-world client storage workloads leave SSDs idle most of the time, so the active power measurements presented earlier in this review only account for a small part of what determines a drive's suitability for battery-powered use. Especially under light use, the power efficiency of a SSD is determined mostly be how well it can save power when idle.

For many NVMe SSDs, the closely related matter of thermal management can also be important. M.2 SSDs can concentrate a lot of power in a very small space. They may also be used in locations with high ambient temperatures and poor cooling, such as tucked under a GPU on a desktop motherboard, or in a poorly-ventilated notebook.

SK hynix Gold P31 1TB
NVMe Power and Thermal Management Features
Controller SK hynix ACNT038
Firmware 41060C20
NVMe
Version
Feature Status
1.0 Number of operational (active) power states 3
1.1 Number of non-operational (idle) power states 2
Autonomous Power State Transition (APST) Supported
1.2 Warning Temperature 83°C
Critical Temperature 84°C
1.3 Host Controlled Thermal Management Supported
 Non-Operational Power State Permissive Mode Not Supported

The power management feature set of the SK hynix Gold P31 is fairly typical. The warning and critical temperature thresholds are only a degree apart, but realistically, this SSD isn't getting anywhere near those temperatures without a lot of outside assistance. The power state transition times claimed by the P31 are pretty quick.

SK hynix Gold P31 1TB
NVMe Power States
Controller SK hynix ACNT038
Firmware 41060C20
Power
State
Maximum
Power
Active/Idle Entry
Latency
Exit
Latency
PS 0 6.3 W Active - -
PS 1 2.4 W Active - -
PS 2 1.9 W Active - -
PS 3 50 mW Idle 1 ms 1 ms
PS 4 4 mW Idle 1 ms 9 ms

Note that the above tables reflect only the information provided by the drive to the OS. The power and latency numbers are often very conservative estimates, but they are what the OS uses to determine which idle states to use and how long to wait before dropping to a deeper idle state.

Idle Power Measurement

SATA SSDs are tested with SATA link power management disabled to measure their active idle power draw, and with it enabled for the deeper idle power consumption score and the idle wake-up latency test. Our testbed, like any ordinary desktop system, cannot trigger the deepest DevSleep idle state.

Idle power management for NVMe SSDs is far more complicated than for SATA SSDs. NVMe SSDs can support several different idle power states, and through the Autonomous Power State Transition (APST) feature the operating system can set a drive's policy for when to drop down to a lower power state. There is typically a tradeoff in that lower-power states take longer to enter and wake up from, so the choice about what power states to use may differ for desktop and notebooks, and depending on which NVMe driver is in use. Additionally, there are multiple degrees of PCIe link power savings possible through Active State Power Management (APSM).

We report three idle power measurements. Active idle is representative of a typical desktop, where none of the advanced PCIe link power saving features are enabled and the drive is immediately ready to process new commands. Our Desktop Idle number represents what can usually be expected from a desktop system that is configured to enable SATA link power management, PCIe ASPM and NVMe APST, but where the lowest PCIe L1.2 link power states are not available. The Laptop Idle number represents the maximum power savings possible with all the NVMe and PCIe power management features in use—usually the default for a battery-powered system but rarely achievable on a desktop even after changing BIOS and OS settings. Since we don't have a way to enable SATA DevSleep on any of our testbeds, SATA drives are omitted from the Laptop Idle charts.

Note: We recently upgraded our power measurement equipment and switched to measuring idle power on our Coffee Lake desktop, our first SSD testbed to have fully-functional PCIe power management. The below measurements are all new, and are not a perfect match for the older measurements in our previous reviews and the Bench database.

Idle Power Consumption - No PMIdle Power Consumption - DesktopIdle Power Consumption - Laptop

The SK hynix Gold P31 has fairly low active idle power consumption: even with PCIe link power management disabled, it doesn't take much to keep this controller awake. The intermediate idle power level that would be typical for many desktop systems is unimpressive, but 87mW is by no means a problem. With all the power management features turned on as should be the case for any properly-configured laptop, the P31's 3mW is competitive (and differences of one or two mW really don't matter here).

Idle Wake-Up Latency

The SK hynix Gold P31 takes just under 6 ms to wake up from its deepest idle state, which is one of the fastest wake-up times we've measured from a drive that successfully enters a deep sleep state when instructed to. Wake-up latencies an order of magnitude higher are still common on many drives, especially those with Silicon Motion NVMe controllers. We were unable to measure any significant latency difference between our "desktop idle" settings and the active idle settings that disable all PCIe link power management; some other drives have been pretty close to this, with mere tens of microseconds delay.

Mixed Read/Write Performance Conclusion
POST A COMMENT

78 Comments

View All Comments

  • jaydee - Tuesday, September 1, 2020 - link

    Thanks Billy! Reading the part about the power efficiency though, any thoughts of quantifying the extra battery life you could expect to see (typical laptop) from the SK Hynix Gold P31 over a Phison E12? The numbers look impressive on paper in terms of percentages against other HDs, but what are we talking about? An extra.. 5/10/15/20 minutes under an extreme R/W heavy workload? What about an average R/W workload? For sure the price/performance is there too so it appears a good buy anyway, I just don't know what to make of the efficiency numbers in terms of actual computing experience. Reply
  • Jimster480 - Saturday, September 5, 2020 - link

    I just put this into my new Ryzen 4600H Powered Nitro 5 and it beats my EX920 in everything! Really a leap in performance and power consumption that wasn't expected from SK Hynix that has been an Also-ran until now! Reply
  • rlr297 - Wednesday, September 23, 2020 - link

    Is there an update on when the platinum drives will be released? I am looking for a 2TB variant. If not, do you have a 2TB drive you'd recommend for a laptop? Reply
  • MatthiasM - Tuesday, November 10, 2020 - link

    Hi All: Can I please ask for collective wisdom? I was very impressed by the review of this drive, especially the low power consumption for laptops. So, I bought one for my 2017 MacBook Air. This can use NVME drive with a Sintech Adapter, no problem. Several other NVME drive (WD, ADTA) run without problems. But when I built in this SK Hynix drive, it wouldn't start. It initiates the boot process, but won't complete it. But when I insert the drive in an external enclosure, it starts from it as boot drive, no problem. Only when it is internal, it won't start. Any suggestions? NVME controller incompatible with MacBook? Any ideas on how to fix this? Reply
  • oRAirwolf - Monday, November 30, 2020 - link

    A little late to the fold, but there was a comment about drive software and firmware updates. SK Hynix released a tool for this drive called Drive Manager: Easy Kit. It's available at the very bottom of this page: https://ssd.skhynix.com/GoldP31.html Reply
  • EarFull - Sunday, February 7, 2021 - link

    Totally over my head, I bought one of these off Amazon after finding out Hynix supplies OEM SSD's for Apple laptops. Thought I'd play with it as a peripheral plug in. Problem is, I can't find an external enclosure that is appropriate for it. I wrote Hynix and they commented it is only for INTERNAL use. Does anyone KNOW of an external enclosure suitable for this 1TB Hynix P31 Gold Drive? I don't care now if it is USB or Thunderbolt. Thank you. Reply
  • EarFull - Sunday, February 7, 2021 - link

    Tried the Hynix P31 Gold NVME in the OWC Envoy Express: did not work. Now OWC site states in this configuration only available for Windows 10. Bummer. Reply
  • EarFull - Thursday, February 11, 2021 - link

    Posted a comment two days ago and can't find it. To reiterate: bought Hynix P31Gold NVME to use as external drive. OWC Envoy Express will NOT work in this configuration on macOS. So, bought this SSK Aluminum M.2 NVME SSD Enclosure Adapter, USB 3.1 Gen 2 (10 Gbps) to NVME PCI-E M-Key Solid State Drive External Enclosure (Fits only NVMe PCIe 2242/2260/2280) to try. Indeed, it works perfectly for about $20. The enclosure is well made, metal, and comes with extra NVME 'screws' and such and two cabes for USB-C to USB-C as well as USB-C to USB-A. Hope this helps. Patrick Reply

Log in

Don't have an account? Sign up now