Fractal Design Define Mini Case Review
by Dustin Sklavos on April 22, 2013 12:01 AM EST- Posted in
- Cases/Cooling/PSUs
- MicroATX
- Fractal Design
- Case
In and Around the Fractal Design Define Mini
If you're used to seeing the other Fractal Design Define enclosures, looking at the Mini may actually hurt your brain a little bit. The Define XL, Define R4, and Define Mini all look fundamentally the same in terms of style and aesthetic, but each one goes a little funhouse mirror in the process. Without examining its dimensions or putting it next to another enclosure, it might be hard to appreciate the slightly smaller form factor of the Define Mini.
.jpg)
The front of the Define Mini sports a padded door that swings open to the left along with ventilation on both sides of it to allow air to flow into the intake fans (and thus into the case) without letting the noise from the intakes escape. There's the familiar LED notch and ring just above it, along with the power button and I/O cluster, all right on the front edge just like the other Defines. Fractal Design hides the reset button behind the door, next to the pair of 5.25" bays. Below those bays are the two intake fans, with doors of their own that swing open to allow you to both change out the fans but also remove their filters for cleaning.
_thumb.jpg)
_thumb.jpg)
_thumb.jpg)
_thumb.jpg)
_thumb.jpg)
_thumb.jpg)
Examining the top, sides, and back of the Define Mini reveals few surprises. The left side includes the traditional ModuVent removable panel to allow the end user to install a 120mm or 140mm side intake fan, while the right side is blank. Meanwhile the top of the case has another 120mm/140mm ModuVent. I'm never really unhappy to see this feature in a case, especially as it's proliferated. Something like this adds flexibility to the case design. Finally, the only hiccup in the back is the fifth expansion slot aligned vertically, presumably for mounting the included fan controller.
Fractal Design uses a pair of thumbscrews to hold each side panel in place, and unfortunately the side panels are notched instead of hinged. I'm never happy to see this, but the Define Mini is at least small enough to prevent the panels from being too difficult to replace.
.jpg)
The motherboard tray is business as usual, with fairly smartly laid out routing holes for cabling. Unfortunately we're only looking at about 160mm of clearance above the motherboard, which makes installing any radiator in there a tight fit; the 120mm exhaust fan also means you'll have to orient any radiator carefully with the hoses above or below the mount.
Everything else inside the Define Mini is Fractal Design par for the course. Of the two drive cages, the top one is removable, but inexplicably, the bottom one is not. Fractal Design opted to use rivets instead of screws to mount the bottom cage, but there's no real reason not to make this something the end user could remove. Thankfully they continue to use their metal drive trays, which are among the best and most secure I've seen.
While the Define Mini is really surprise free for anyone familiar with Fractal Design's cases (and thus knowing what to expect), there's one tremendously goofy wrinkle: only one USB 3.0 port. It uses the full internal motherboard header, but every time I see something like this it seems like such a waste, especially when there's obviously space in the fascia to include a second. Outside of this, though, the Define Mini is at least superficially what you expected and were hoping for.
Facebook
Twitter
RSS
57 Comments
View All Comments
wzrds3 - Monday, April 22, 2013 - link
My TJ08-E is still quite loud, even on the fan's low setting.flipmode - Monday, April 22, 2013 - link
I've done 6 builds with the TJ08-e. For every one of them I have found the front intake fan to be too loud even on the low setting. Plugging into a motherboard with fan speed control helps, but can also cause the front fan to stop spinning at times.At home, it is an extremely audible case.
At work, I can't hear the thing at all even sitting right next to me.
That is the extent to which ambient noise is a factor. People that call this case quiet may be dealing with higher ambient noise.
I think after 6 builds I feel pretty confident that I know the typical acoustic character of the TJ08-e
flipmode - Monday, April 22, 2013 - link
Also, the drive cage in the TJ08-e is a serious drawback. None the less, it remains my go-to mATX case.JPForums - Monday, April 22, 2013 - link
I've done 4 builds with the TJ08e. I agree they aren't silent, but none of my builds turned out particularly loud either. While ambient noise can be a factor in the perception of what is quiet, I think this may be a difference in standards of quiet. In my most recent build with the TJ08e, the Zalman 9900CNPS is the loudest component. By my standards, the 9900CNPS while not silent, is quiet. The ambient noise environment shouldn't make a difference as to which component is loudest in the build, so if you find the 9900CNPS comfortable, then the TJ08e has the potential to work for you. Just don't expect it to mute louder internal components given it has no acoustic padding.JPForums - Monday, April 22, 2013 - link
I should mention that I forgo the HDD cage all together and mount a single SSD in the bottom bracket that the HDD cage mounts on top of. It makes a difference to airflow. Might make a difference acoustically as well.cragAT - Tuesday, April 23, 2013 - link
That is exactly what I did with my build, with my secondary HDD up in the 5.25 bay. No sound/temp issues at all.madwolfa - Monday, April 22, 2013 - link
I have a TJ-08E, it's nearly silent in my very quiet home environment. I use the "full speed" setting of the switch (so it has enough voltage to start), and then put it down to 400-500 RPM with FanXpert control of my Maximus V Gene. Still plenty of airflow and totally silent.EnzoFX - Monday, April 22, 2013 - link
I'm pretty sure Dustin's tolerance for noise is a bit higher. I wouldn't call the low setting quiet at all. As for undervolting, you don't need to weld or use a resistor, all you do is the 5v,7v,12v trick of swapping molex wires cables.smellykaka - Tuesday, April 23, 2013 - link
Yes, I have the fan on the low setting, it is still way more audible than a Fractal Design case.MadMan007 - Monday, April 22, 2013 - link
Meh. I know they had to do it to fit in the drive racks the way they have them but once again this is a micro ATX case that's a scant few inches smaller in one dimension than mid-tower ATX cases. I just don't see the point. If you really want a compact case there *will* be real compromises, tight fits, and less easy assembly than wide open ATX cases. But any 'micro' ATX case that's got a dimension of around 20" is just missing the point of micro ATX.