Intel Z77 Panther Point Chipset and Motherboard Preview – ASRock, ASUS, Gigabyte, MSI, ECS and Biostar
by Ian Cutress on April 8, 2012 12:00 AM EST- Posted in
- Motherboards
- Intel
- Biostar
- MSI
- Gigabyte
- ASRock
- Asus
- Ivy Bridge
- ECS
- Z77
ASRock Z77 Extreme4—Visual Inspection
ASRock are still insistent with bringing the black gold philosophy to its range, as seen here with the Z77 Extreme4 and later with the Z77 Extreme6. The main point you may immediately notice is the size and depth of the heatsinks covering up the power delivery—they are smaller than previous iterations of ASRock boards, and no longer connected via a heatpipe. This is indicative of quite a few boards we are looking at today, due to the low power requirements of the new processors and as a result, the lack of heat produced at stock voltage.
The socket area is relatively clean, especially to the south where we have no large intruding heatsink. The VRM heatsinks however do brush right up against the Intel specifications for the socket area, so you ultimately have only two directions (to the PCIe and towards the memory) in which to play around with big air coolers. The socket area is adorned with five fan headers—three along the top edge of the board and two chassis headers near the top PCIe x1 slot. The other header on board is along the bottom next to the two-digit debug.
The board is actually not a full ATX sized board—from left to right, it measures only 21.8 cm, rather than the standard ATX size of 24.4 cm. As a result this means ASRock do not have to deal with the far right holes in the motherboard for case mounting, and hence why the SATA ports in the bottom right are neatly tucked away. In this corner, we have the six SATA ports from the PCH (two SATA 6 Gbps, four SATA 3 Gbps) and another two from an ASMedia ASM1061 controller (SATA3_A1 is shared with an eSATA port, however). The internal USB 3.0 header is located nearer the 24-pin ATX power connector, perhaps indicating that is for both front case use and rear case use, taking up the space where the first PCIe x1 is.
The chipset heatsink is rather small, compared to Z68 and X79 boards, and is not connected via heatpipe to any other heatsink nearby. On the south side of the board are the standard array of audio and USB headers, along with a fan header and power/reset buttons. It is good also to see the two digit debug on the board as well.
The PCIe layout is indicative of what we will see on many Z77 boards this year, which do not use any form of PCIe lane expansion, such as a PLX chip. In this case, we have an x1, an x16 (x8 on dual card), a gap, a PCI, an x8, another PCI, and another x1. This is some smart thinking, as even with a dual GPU setup there is space for two single width PCIe x1 cards and a PCI card (which contrary to what some people think are still used in reasonable numbers).
Despite the stock image from ASRock looking a little bent on the back panel, we have a typical Z77 arrangement for IO. From left to right, a combination PS/2 port, two USB 3.0 ports (blue), a D-Sub output, a DVI-D output, HDMI, a clear CMOS button, two USB 2.0 ports (black), an eSATA port (red), gigabit Ethernet, two more USB 3.0 ports (blue), and a standard array of audio jacks featuring an optical SPDIF output.
Board Features
| ASRock Z77 Extreme4 | |
| Size | ATX |
| CPU Interface | LGA-1155 |
| Chipset | Intel Z77 |
| Power Delivery | 8 + 4 Phase |
| Memory Slots |
Four DDR3 DIMM slots supporting up to 32 GB Up to Dual Channel, 1066-2800 MHz |
| Video Outputs | HDMI 1.4a, DVI-D, D-Sub |
| Onboard LAN | Broadcom BCM57781 |
| Onboard Audio | Realtek ALC898 |
| Expansion Slots |
2 x PCIe x16 Gen3 2 x PCIe x1 Gen2 2 x PCI |
| Onboard SATA/RAID |
2 x SATA 6 Gbps (PCH), Support for RAID 0, 1, 5, 10 2 x SATA 6 Gbps (ASMedia ASM1061) 4 x SATA 3 Gbps (PCH), Support for RAID 0, 1, 5, 10 |
| USB |
Two USB 3.0 at rear (PCH) Two USB 3.0 at rear (ASMedia 1042) One USB 3.0 header (PCH) |
| Onboard |
4 x SATA 6 Gbps 4 x SATA 3 Gbps 1 x IR Header 1 x CIR Header 1 x COM Header 1 x SPDIF Header Power/Reset Buttons Two Digit Debug LED 6 x Fan Headers Front panel audio connector 3 x USB 2.0 headers (support 6 USB 2.0 ports) 1 x USB 3.0 header (supports 2 USB 3.0 ports) |
| Power Connectors |
1 x 24-pin ATX connector 1 x 8-pin 12V connector |
| Fan Headers |
2 x CPU Fan Header (one 4-pin, one 3-pin) 3 x CHA Fan Headers (one 4-pin, two 3-pin) 1 x PWR Fan Headers (3-pin) |
| IO Panel |
1 x Combo PS/2 Port 1 x HDMI 1.4a 1 x DVI-D 1 x D-Sub 1 x Optical SPDIF 2 x USB 2.0 4 x USB 3.0 1 x eSATA 6 Gbps 1 x Gigabit Ethernet 1 x Clear CMOS Audio Outputs |
| Warranty Period | 3 years from date of purchase |
| Product Page | Link |
Rather than dump a Realtek NIC/Audio combination on this board, ASRock have gone for a Broadcom NIC. This means either they have struck a deal, or it works a lot better for their ASRock LAN software. ASRock are one of few motherboard manufacturers to state they support HDMI 1.4a on their website specifications as well. As one of the cheaper boards of this roundup, the Z77 Extreme4 actually comes away pretty well in terms of features.
Facebook
Twitter
RSS
145 Comments
View All Comments
mechjman - Monday, April 9, 2012 - link
I don't remember seeing PCIe 3.0 support straight from P6x series chipsets.http://www.intel.com/content/www/us/en/chipsets/ma...
If this is regarding in use with a PLX chip, it might be good to state so.
extide - Tuesday, April 10, 2012 - link
It's actually when the boards DONT use a plx chip, or if the use 3.0 capable ones. It's only the boards that use 2.0 chips that are limited to 2.0GameLifter - Tuesday, April 10, 2012 - link
I am very curious to see how this technology will affect the overall performance of the RAM. If it works well, I may have to get the P8Z77-V Pro.jbuiltman - Tuesday, April 10, 2012 - link
I am leaving my AMD FX-60, 3 GB DDR, Asus 939 Delux, Win XP, Raptor 150 HDD for IVY Bridge pasures!!!I am all for ASUS 16+4 power, multi usb 2.0 and 3.0 on the back panel. I also like the multiple 4 pin fan plug ins, mem ok, LED problem indicator, switches, 4 SATA 6GB connectors and heat pipes connecting the alunimum fins.
What i want to see is 16x/16x not 8x/8x on dual video card on a Z77 board. ASUS, don't skimp for a measly $30! I hate cheap companies and don't make me think you are just being cheap!!!
jbuiltman - Tuesday, April 10, 2012 - link
Hey all you MoBo companies. Don't get cheap with the Z77 boards and not include 16x/16x on the pci-e 3.0!!!! Come on, add what you need to and pass the $30 on to me!!!!ratbert1 - Wednesday, April 11, 2012 - link
"ASUS as a direct standard are now placing Intel NICs on all their channel motherboards. This is a result of a significant number of their user base requesting them over the Realtek solutions."Um... ASUS P8Z77-V LX has Realtek!
and...ASUS P8H77-M PRO has Realtek!
There are more.
ratbert1 - Wednesday, April 11, 2012 - link
I meant P8Z77-M PRO, but the H77 has it as well.lbeyak - Sunday, April 15, 2012 - link
I would love a detailed review of the Gigabyte G1.Sniper 3 Z77 board when it becomes available.Keep up the good work!
csrikant - Sunday, April 22, 2012 - link
Dual E5-2690So far best i have got burn a lot $$$ to get this right
my last build was with I7 990x got itchy in oct 2011 with some minor issue decided to change my PC got my i7 2700K did not meet my expectation
built i7 3960x still failed many of my requirements regret my pc change from 990x
Finally with all my pain and wasting$$ got my new build that so far perform better than my 990X build
My advice do not get carried away by fancy new i7 release they are just little benefit for P4 just wasting time I was shocked that they released P4 with 1155 socket it was having same performace as 2700K not much change in fact it was cheaper too.
Am not expert an average system builder but my advice from bottom of my heart is just go for E5 build if you are really looking for performace and some benefits you may spend some extra $$ on MB ,CPU,Casing etc it is worth in long run works out cheper than any fancy High end gaming rig water cooling etc all just shit tech advice. Never get ferrari performance form mod toyota.
mudy - Monday, April 23, 2012 - link
With the third pcie lane on the z77 boards I have come across almost all manufacturers saying "1xPCI Express 2.0 x16 (x4 Mode) & only available if a Gen 3 CPU are used". Does this mean that the lane is pcie 2.0 at x16 but works at pcie 3.0 x4 mode, if an IVB processor is connected, and other two pcie 3.0 lane is populated giving x8/x4x4 speed with pcie 3.0 compliant cards?? Also what will happen if I put Pcie 2.0 GPUs in the first two pcie 3.0 x16 slots and a pcie 2.0 compliant raid card (rr2720SGL) in the third pcie lane? Will it give me an effective pcie 2.0 bandwidth of x16/x8/x8 or not?? Damn these are so confusing!! I wish anandtech would do an extensive review on just the pcie lanes covering all sorts of scenario and I think NOW would be the best time to this as the transition from pcie 2.0 to pcie 3.0 will happen slowly (maybe years) so majority end-user will still be keeping their pcie 2.0 compliant devices!!Thanks