DC Output Stability and Quality

The voltage regulation works quite well with the DA700 as we can see above. We see some larger drops with the 3.3V rail but it drops from being somewhat high to the ideal 3.30V which is better in our opinion than starting at 3.30V and ending up low. The 5V rail is nearly flat, staying in the 5.05V to 5.1V range throughout the tests - slightly high, but well within spec. The more important 12V rail, which was actually designed with four separated rails, has similar good readings and always stays just above the specified 12.00V. The fluctuations are so small that the graph shows a very thin line. As for the output quality, we can say the Silverstone DA700 has very clean results as well. All of the rails performed within specification and the 12V rail had just a little over 20mV ripple at higher loads.

Let's have a look inside... Efficiency and PFC
Comments Locked


View All Comments

  • Stefan555 - Tuesday, April 22, 2008 - link

    Yes Chris, the physical layout of the PCB show there are four rails. It doesnt mean each rail has a limiter. Whitout limiters = SINGLE rail unit.
  • Kanchenjunga - Tuesday, April 22, 2008 - link

    You'd think that somebody who just reviewed the single 12V rail Impervio made EliteXStreams with 5 rails printed on the PCB and color coded wires would have this figured out by now. How come you guys don't do the OCP test that your testing method article talks about?
  • Christoph Katzer - Tuesday, April 22, 2008 - link

    I guess that sentence where I mention the four rails has been just misleading as I didnt mean to say it's a four 12V rail PSU. I will change that for the sake of a good sleep tonight :)
  • MrOblivious - Tuesday, April 22, 2008 - link

    What was the OCP set at for each of the 4 12v rails?
  • Stefan555 - Tuesday, April 22, 2008 - link

    "The rail specification is rather obfuscated, requiring several perusals and the use of a calculator before you actually understand what you're reading."

    It's simple, what we are reading is the label, the label tells you it has an capability to put out 58A on one single rail on +12V (no matter the reality one or four rails). It also tells you the psu has the capability to put out 180W or combined on +3.3 and +5V. I can't see what is so obfuscated?

    "The DA700 comes with a single 12V rail rated for up to 58A which is almost 700W already. Obviously, that load is not possible with the combined power of all three main rails; doing the necessary math, if you put a load of 180W on the 3.3V and 5V rails, that leaves 520W for the 12V rail, or 43A."

    On which psu can you take the maximum combined output on +3.3V and +5V and add it with the maximum capability on +12V and get anywhere near the total specified wattage on the psu? None.
    There is no psu where you can draw the maximum output on +3.3V and +5V combined and +12V at the same time.

    This unit is not the only psu where the combined output on +12V is so high its more a theoretical maximum output. Other units has even less left for +3.3V and +5V. But that is pure theory.

    If now the unit has four rails on +12V, well that is a bit of lame of Silvertone not to tell it. I agree. But still, it has nothing to do with the readability of the label. Besides it is mentioned later in the review.

  • Calin - Tuesday, April 22, 2008 - link

    "The problem is that there are quite a lot of patents on larger fans"
    How the hell could a larger fan be patented? What kind of backward country is that?
  • Christoph Katzer - Tuesday, April 22, 2008 - link

    The patent is a power supply cooled by a 140mm fan. That's why other manufacturers (other than CWT the patent owner) need to make use of 135mm or 120mm fans. In the U.S you get patents for all kinds of stuff...
  • masher2 - Tuesday, April 22, 2008 - link

    Sounds like an urban myth to me..
  • MrOblivious - Tuesday, April 22, 2008 - link

    SuperFlower has been using 140mm fan's for years, indeed IIRC before CWT.
  • strikeback03 - Tuesday, April 22, 2008 - link

    Time for someone to make a 141mm fan

Log in

Don't have an account? Sign up now