The Interior of the Corsair Carbide 400Q

The side panels of the Carbide 400Q can be easily detached by removing two thumbscrews for each. Both of the side panels, and including the top panel cover and the faceplate, have a thin layer of sound dampening material applied to them. Considering the openings on the sides of the front panel and the rear of the case, the impact of the material on the acoustics of the case is unlikely to be very high, but every little bit can help.

The interior of the Carbide 400Q is all black, including every cable, screw and stand-off. The only parts breaking the blackness of the case are the grey impellers of the stock cooling fans. The metallic surfaces are sprayed with the same satin black paint as the exterior. The plastic covers across the PSU compartment and HDD cage are sprayed with the satin black paint as well, but it is not nearly as fingerprint resistant as the metallic parts of the case. Strangely, only the three main openings next to the motherboard feature rubber grommet covers. There are more openings next to those, as well as several more above and below the motherboard, none of which has a rubber grommet installed.

Lacking any front/external drive cages, the interior of the Carbide 400Q is very spacious, allowing for the installation of E-ATX motherboards. Graphics cards up to 370 mm long will fit as well, but note that the installation of fans or radiators will reduce that clearance. A large rectangular hole is cut on the motherboard's tray to allow for the installation of aftermarket coolers without having to remove the motherboard. Some of the very large air coolers may not fit in the Carbide 400Q, as the height of the CPU cooler is limited to 170 mm.

To remove the two plastic covers that separate the PSU and HDD area from the rest of the case, the HDD cover has to come off first, then the PSU cover. There is a hole at the top of the covers that allows for the routing of a PSU cable directly towards the system, but we found that to be greatly inconvenient because it then has to be disconnected for the covers to be removed. Considering that this particular design has no side window, the very presence of the covers is strange to begin with.


After the covers have been removed, the PSU area and HDD cage can be clearly seen. The Carbide 400Q can hold PSUs up to 190 mm long, but we do not recommend the installation of such long units. To install such a PSU, the HDD cage will have to be moved to its auxiliary position, towards the front of the case, and routing the cables through the right panel’s openings becomes troubling. Furthermore, moving the HDD cage to its auxiliary position will block the installation of radiators at the front of the case.

The Carbide 400Q is somewhat limiting when it comes to drives. Three 2.5” drive trays can be found at the rear side of the motherboard’s tray and another two 3.5” or 2.5” drives can be installed on the removable plastic trays of the small drives cage. Nevertheless, the number of drives that the Carbide 400Q supports should be sufficient for the vast majority of home and office users.


For the means of this review, we installed a Corsair AX760i with the red cable set, for strong visual contrast. The AX760i fits tightly inside the Carbide 400Q without moving the HDD cage to its auxiliary position, with the installation of extra cables after the PSU has been installed being all but impossible. The cables are long enough for a standard system and their routing across the rear of the motherboard tray and through the rubber grommets is very easy.

A standard ATX system comfortably fits inside the system area of the Carbide 400Q, allowing for easy upgrades and maintenance. Since the case is designed to hold up to E-ATX motherboards, the openings for the cables are a few centimeters away from the edge our standard ATX motherboard. There is more than enough space for long cards and most models should fit even if a radiator has been installed at the front of the case. The clearance above the motherboard is small but Corsair offset the top mounting slots towards the left side of the case, allowing for the installation of fans and radiators. Tall motherboard heatsinks and RAM modules however can create compatibility issues here.

The Exterior of the Corsair Carbide 400Q Testing and results
Comments Locked


View All Comments

  • vanilla_gorilla - Friday, April 29, 2016 - link

    " It is the balance between them that matters and we feel that Corsair did a fine job balancing their design to the best possible extend."

    Extend? You mean extent? Even that seems poorly worded. Editors asleep over there?
  • vanilla_gorilla - Friday, April 29, 2016 - link

    " It is next to impossible to bent or twist the chassis, even if a lot of force is applied. "

    You mean bend?
  • retrospooty - Sunday, May 1, 2016 - link

    Seriously, the world doesn't need another grammar Nazi. This is the internet not an official textbook
  • random2 - Wednesday, May 11, 2016 - link

    This is a journalistic article, by a paid contributor or editor, available for the world to view and is at least a semi permanent record so there is a certain level of professionalism expected. Proofing these articles before posting is not difficult or even that time consuming. Not proofing is just asking to be entered in a race to the bottom...speaking from a journalistic point of view.
  • economymatthew - Friday, April 29, 2016 - link

    A pretty b itchy response to a free product review
  • jardows2 - Friday, April 29, 2016 - link

    Apparently you haven't been reading the comments section of AnandTech articles for long. Always someone quick to point out typos and grammatical errors!
  • Samus - Friday, April 29, 2016 - link

    Ignore the trolls. Odds are this site is older than they are.
  • Valantar - Saturday, April 30, 2016 - link

    Age is a poor differentiator when it comes to whether or not to ignore trolls. Fully grown trolls are just as undeserving of our attention as those still in their larval stages.

    More to the point: sure, pointing out typos and other error in a long article can be helpful (there's a reason why proof reading used to be a profession!), but as with everyone else on the internet, we could do with an extra dose of humility and politeness.
  • random2 - Tuesday, May 10, 2016 - link

    Younger trolls care not about grammar.
  • boozed - Friday, April 29, 2016 - link

    Occasionally the pedantic nonsense is necessary, such as when an error stems from a fundamental misunderstanding of the meaning of words.

    Pointing out typos is tedious however. How hard can it be to implement a "send correction" form? Plenty of sites have them and it gives people somewhere to put their pedantic nonsense without drowning out the main comments.

Log in

Don't have an account? Sign up now