BitFenix Prodigy Review: The Affordable Performable Mini-ITX
by Dustin Sklavos on June 1, 2012 1:55 AM EST- Posted in
- Cases/Cooling/PSUs
- Mini ITX
- bitfenix
Testing Methodology
For testing Mini-ITX cases, we use the following standardized testbed in stock and overclocked configurations to get a feel for how well the case handles heat and noise. Again, note that while the GD07 can technically fit a full-size ATX motherboard, it's not tall enough to allow for our testbed's tower cooler. Because of the discrepancies that would make for in testing, plus the fact that media center cases are often mini-ITX designs, we have chosen to use our mini-ITX testbed rather than going with a specialized (e.g. not something you can compare directly to our other cases) ATX build.
| Mini-ITX Test Configuration | |
| CPU |
Intel Core i3-2120 (65W TDP) |
| Motherboard | Zotac Z68ITX-A-E |
| Graphics Card |
Intel HD 2000 IGP Zotac GeForce GTS 450 Eco (dedicated) ASUS GeForce GTX 560 Ti DCII TOP (dedicated extra) |
| Memory | 2x2GB Crucial Ballistix Smart Tracer DDR3-1600 |
| Drives |
Kingston SSDNow V+ 100 64GB SSD Samsung 5.25" BD-ROM/DVDRW Drive |
| Accessories | Corsair Link |
| CPU Cooler | SilverStone NT07-1156 with Cooler Master ThermalFusion 400 |
| Power Supply | SilverStone SFX ST45F 450W |
Each case is tested with just the Core i3's integrated graphics as well as with a discrete graphics card. The system is powered on and left idle for fifteen minutes, the thermal and acoustic results recorded, and then stressed by running four threads in Prime95 (in-place large FFTs) on the CPU, and OC Scanner (maximum load) is run when the dedicated GPU is installed. At the end of fiteen minutes, thermal and acoustic results are recorded. If the enclosure has a fan controller, these tests are repeated for each setting. Ambient temperature is also measured after the fifteen idle minutes but before the stress test and used to calculate the final reported results.
We try to maintain an ambient testing temperature of between 22C and 24C. Non-thermal test results aren't going to be directly comparable to the finest decimal point, but should be roughly comparable and give a broader idea of how the enclosure performs.
Thank You!
Before moving on, we'd like to thank the following vendors for providing us with the hardware used in our testbed.
- Thank you to Puget Systems for providing us with the Intel Core i3-2120.
- Thank you to Zotac for providing us with the Z68ITX-A-E motherboard and GeForce GTS 450 Eco.
- Thank you to Crucial for providing us with the Ballistix Smart Tracer memory.
- Thank you to Corsair for providing us with the Corsair Link kit.
- Thank you to Kingston for providing us with the SSDNow V+ 100 SSD.
- Thank you to CyberPower for providing us with the Samsung BD-ROM/DVD+/-RW drive.
- And thank you to SilverStone for providing us with the power supply and NT07-1156 heatsink/fan combo.
Facebook
Twitter
RSS
79 Comments
View All Comments
Peter_s - Friday, June 1, 2012 - link
I bought in 2004 this case. Looks like a MacPro? Not realy. But it is keeps my stuff cool.I removed the lower handle (stand). The cas had not a good stand with it. As one posted the Bitfenix lacks stability too.
P.S. I own a lot of Apple's hardware too. Simply for convenience ;-)
But will I (you) buy a MacProCase and do all fiddling to fit a PC in? I will go this route.
Probably I will buy th Bitfenix and remove the handle the plastic stand immediatly.
Peter_s - Friday, June 1, 2012 - link
Oopsgot this case in 2004 (MacPro inspired)
http://www.caseumbau.de/test263/bild002.jpg
Guspaz - Friday, June 1, 2012 - link
I recently bought a Shuttle SZ77R5 (apparently one of the first Shuttle XPC units to support replacing the mobo with a mini ITX mobo). One of my friends kept insisting that it was, at $340, supremely overpriced. On the other hand, it's not just a case, it also comprises a motherboard, power supply, and CPU cooler (although I won't count that since Intel CPUs come with one free).So, how expensive is it, relatively speaking? I'll compare the cost of a similarly built BitFenix:
BitFenix Prodigy: $79
80+ bronze PSU: $65
Asus Z77 mini-itx mobo: $200
The mobo is expensive, but NewEgg only sells two mini ITX Z77 models. The other one is cheaper, but neither of these have as much connectivity options as the Shuttle (neither has 4 DIMM slots, a second 4x PCIe slot, a miniPCI slot, or an mSATA slot), so it's probably still a fair comparison.
What do we get? A fully configured BitFenix would be $344 and still not match the featureset... Suddenly that Shuttle doesn't seem so expensive anymore, does it?
I'm not knocking the Fenix, mind you, I'm just venting at my friend who will probably never see this.
GotThumbs - Friday, June 1, 2012 - link
I really like the layout of this case. The quality seems to be very good and I personally don't care about the name on the case....as long as the build quality is good. Being able to add my choice of PS is a good feature. I'd be interested in getting this case if it was just a little smaller in size. I'm currently using a modified APEX MI-008 for my WHS. I pulled out the 5.25 drive cage and have four drives suspended in the front. I only need a box large enough to hold the ITX board and HD's. I rip my content on my main system and then load onto the server, so no need for an optical drive in the server. I'll be keeping my eye on this company and their case selection.Good article and appreciate the photos and not limiting reviews to only 'Big" name brands. Only a fool would accept limiting their options IMO.
DesertCat - Friday, June 1, 2012 - link
To be fair, many of the cases that are competitors to this unit also do best with ATX PSUs that are only 140mm long. I think some people with the Lian Li PC-Q11 have been able to use 150mm long PSUs but things start to get really crowded between the front intake fan and the back of the PSU. Having about half of your front intake fan blowing onto the back of the PSU at a distance of 1 cm isn't exactly ideal. With some of their other models, long PSUs will run into the drive cage. So... I think BitFenix is going with a PSU length that is typical for many of these cases (though people may still not like that).For those that don't mind having a non-modular PSU (and the associated cable tucking), an ideal solution for many of these little cases is the Nexus NX-5000 R3 (530W) or NX-6000 R3 (630W). They are only 125mm long. That is a model that doesn't show up at many of our favorite online retailers though, but a bit of search engine magic will allow people to find a U.S. retailer that carries them.
versesuvius - Friday, June 1, 2012 - link
The case is 25 cm thick? And this is supposed to house a micro ATX board? At 40 cm height, it is already an ATX case. So, what is the point of the micro ATX board? Who is this case trying to fool?LOUiECOG - Friday, June 1, 2012 - link
Mini-ITXversesuvius - Saturday, June 2, 2012 - link
Just the same. This case is just too big for the board. No point in using it for any purpose. BitFenix already produces cases that are cheaper than this, look a lot better and have the same volume, that can house boards and cards much larger than this case can accommodate, with the most important benefit that they have a %20 less footprint. When people are talking about small in workplace or home they are not usually talking about the height, it is mostly about width and depth. This case fails on both accounts.Sogekihei - Monday, June 4, 2012 - link
And yet this probably wouldn't exist if there wasn't some demand for such a product. Clearly somebody wants to build mini-ITX for whatever reason (lowered power consumption, integrated components such as Bluetooth and WiFi adapters) but still have a moderately powerful system, perhaps for home theatre purposes or as a game console/arcade game emulator. Considering all of the Sandy Bridge and Ivy Bridge-based mini-ITX boards available as well as the presence of moderately powerful single slot-width graphics cards such as some revisions of nVidia's GTS 450, this is not only possible but to some extent wanted by consumers, as such things would end production after their first iteration if they weren't commercially successful.As the article mentioned, mATX basically has the same features as ATX at this point with both offering multiple PCI-e slots and numerous slots for additional system memory. For purpose-built systems that don't need large quantities of RAM or multiple graphics cards, RAID controllers, dedicated sound cards, etc, mini-ITX might become the new low-end/mainstream form factor and replace mATX in that regard.
I really feel like your complaints about this would have been equally applied back in the days when mid-tower and smaller case sizes first became prevalent, where you aren't seeing the full appeal of either the new mainboard form factor or you're under/over-estimating size differences; these days height can be a limiting factor with a lot of people wanting to have systems that they can place on a shelf of their entertainment center like a DVD player or video game console.
HardwareDufus - Friday, June 1, 2012 - link
I have a heavily modified Travala C138 2Din Mini-ITX enclosure.It began life as a Stock C138 enclosure with a Via C7 mini-ITX board. CPU and Case Fans were 40mm. Held a slimCD/DVD and one 3 1/2 drive. (Travala has modified this model recently and now there is the option for two 2 1/2 drives.)
I drilled many, many ventalation holes, machined out extra metal inside that blocked airflow, machined custom rails to accept the 2.5" drives, but allow for airspace on all 4 sides of the drives, etc...
Now it holds an 80mm Silenex 11dba Intake on the right side, 80mm Silenex 11dba Exhaust on the left side... and a 80mm Silexex 14dba Fan on the low profile heatpiped copper cpu cooler. Upgraded the powersupply to 120W.
I shortened/soldered/etc.. all cables for minimum space/folding.
It is equipped with the Gigabye H55N motherboard, two Seagate 2.5" 7200pm 500MB harddrives, A clarksdale I5 DualCore HT processor (655K) overclocked to 3.8Ghz, and a Sony slim BlueRay DVD, 8 GBs of Ram.
It is whipser quiet. Temps are reasonable... at full load I have seen the temps climb above 60degC, but normally stay around 40degC....not bad for living in the mexican desert...
Well now I want to go to IvyBridge..at 4Ghz with 16GB of Ram.. and I want to swap out the harddrives for SSD. And I want to stay mini-ITX... The Asus Z77 mini-ITX Deluxe board looks fantastic.. but it has that weird raised power daughter card that will get in the way of my 80mm Intake....
So, I'm looking for a better case. How frustrated I am that I cannot find one that matches mine..... I don't mind going a little bigger... But it seems you go tiny and fanless... or huge with space for 4 to 6 harddrives?
The search is frustrating..