Codegen 6209 (cont'd)

Construction

The 6209 is made of 0.7mm steel, which makes it strong enough to withstand a lot more stress than the steel in the 3131G and it will definitely not bend because of power supplies or any other hardware.

The thicker steel also reduces sharp edges. We could not find any when we felt around the case, which is excellent.


Cooling

The 6209 comes with a single 80mm fan mounted at the back of the case and has room for one more at the front as an intake.

If you look on the left side panel, you will notice that Codegen has also implemented an air duct for the CPU, which will guide cool, outside air directly to the CPU.

There is also an optional PCI-E vent towards the middle of that same panel to help alleviate heat produced by a PCI-E graphics card.


Installation

Installation went as smooth as possible and took about 10 minutes to install all of our components. The tool-less expansion slots were also an unexpected feature and further reduced the time for installing add-in cards.

We wondered how much more it would cost to add such things as tool-less stand-offs to secure the motherboard without a screw driver, or even drive rails to the drive bays. Maybe we can see this in the future of value-priced cases?


Codegen 6209 Powmax CP769PL
Comments Locked

58 Comments

View All Comments

  • Phantronius - Wednesday, February 2, 2005 - link

    All these cases reak of over the top design and piss ass quality standards. I've worked on a wide variety of cases and I gotta tell you, the cheap as cases look and feel like they were put together with monkeys.

    There something definently wrong when a steel case starts to bend from the weight of a PSU.
  • TheInvincibleMustard - Wednesday, February 2, 2005 - link

    Agreed with others (#13, #46) about the PowMax ... the words "PowMax" and "high quality power supplies" do not belong in the same sentence unless there's the words "does not make" inserted between them. ;)

    All in all, though, I've got to echo what others are saying here. There is very little mention about the PSUs that come with these units (including that one that has 12A (!!!) on the +12V line). Your "average" system is way out of whack for these machines, too ... explain how someone is going to spend $100 on a high-quality PSU like that OCZ and then spend $25 on a case? Try again, Purav ... this time maybe with a system that would better fit the budget ideas behind a case of this price range? Sempron, s754, 6200, etc etc.
  • Agentbolt - Wednesday, February 2, 2005 - link

    PowMax PSUs are extremely high quality, huh? Tell that to my old Abit NF7 that got fried by a ridiculously out of whack PowMax 400W PSU. Oh, and the 8,000 or so ohter people complaining the same thing happened to them on NewEgg.com

    PowMax PSU are absolutely and utter garbage that are too light to even use a paper weight. Anyone trusting an entire computer's worth of components to one needs to be shot.
  • hoppa - Tuesday, February 1, 2005 - link

    #44 i couldnt agree with you more. among many fellow comp sci majors here at school ive got one of, if not the, fastest system, and im only sitting on a barton 3000+ / 9800 pro. i do have the zalman though =P
  • Avalon - Tuesday, February 1, 2005 - link

    We have hand-picked a full system that we believe is the current system setup for the average user.



    PC Mid-Tower Test Bed
    Chaintech VNF3-250
    AMD Athlon64 3200+
    OCZ PC3200 DDR x 2
    Zalman CNPS7000 Copper
    Seagate Barracuda 120GB SATA
    ATI 9800XT
    OCZ 520W PowerStream

    What the hell is that? Since when do average, everyday Joe's use 520w OCZ PSUs and Athlon 64 processors? Most users who would consider cases like these are using sempron, athlon, celeron, and duron systems.

    If you want a decent budget case, my favorite is this one:

    http://www.newegg.com/app/ViewProductDesc.asp?desc...

    $24 with shipping. Comes with no fans, but the PSU is sturdy and will support Athlon XPs, Durons, Semprons, and Celerons just fine, sans overclocking. The case itself is sturdy, and there are no sharp edges in it. Aesthetically speaking, it doesn't look beautiful, but it looks far from bad. I've used this case on quite a few occassions. However, I too would recommend ponying up the extra $20-$30 for an Antec case.
  • Cygni - Tuesday, February 1, 2005 - link

    Dude, give it a rest... anandtech isnt a goverment body, and they dont have to retract anything, haha. EVERYONE has comments about how this or that detail is just BARELY off, or because AT "Shouldnt" be publishing an article because its aimed at the low end, or the high end, or the IT sector, or the Mac world, or whatever. The comments on most AT articles these days are just forums for people to bitch meaninglessly.
  • sirmixmasta - Tuesday, February 1, 2005 - link

    The Codegen 6209 has USB 1.1 front USB ports instead of USB 2.0 ports like every other new case. This case should CLEARLY NOT BE THE EDITORS CHOICE. The front USB ports will be useless for anyone with a new motherboard. I personally own other Codegen cases with the same USB 1.1 front USB ports and they will not work with any newer motherboard that is USB 2.0 compliant. The cases front usb cabling/connector will not correctly fit a USB 2.0 motherboard pin-out. Even when altered to fit, you will find that use of the front USB ports with a 2.0 complaint USB device will lock up all your USB ports or worse, freeze your entire system.

    This article should be retracted for the time being until this fact is confirmed or explained in some way by the author. I find it hard to believe that AnandTech would recommend such a case with this obvious shortcoming. Additionally, some of the other comments by readers need to be addressed as well.


    http://www.newegg.com/app/viewproductdesc.asp?desc...

    http://www.codegengroup.com/03_products/index.asp?...
  • sdfg - Tuesday, February 1, 2005 - link

    Kristopher,

    Yeah, I think I do, too...
  • dgkulzer - Tuesday, February 1, 2005 - link

    I bought a evercase 4252 for 45 bucks without a PSU. It had all the features that I needed like space for a 120 fan in the rear, 2 front USB, non-flashy design, and good airflow. I bought this case to replace a more expensive case (Antec Sonota) which I didnt like because it was the first case I ever had with a door over the optical drives and it annoyed me.

    My computer now has a Seasonic SS450 PSU, AMD64 3200 (S754), 1 gig of ram etc and I don't think I will ever buy a 'expensive' case again. If you look around you can find some very nice low-cost cases. I would generally replace the PS though
  • IceWindius - Tuesday, February 1, 2005 - link

    I love my Chieftec Aluminum Dragon. Until Antec switches to aluminum, I will continue to turn plain jane cases into works of art using chieftecs

Log in

Don't have an account? Sign up now