Lian Li PC-A55 Case Review: Unfortunate Name Befits the Design
by Dustin Sklavos on June 16, 2012 12:30 PM EST- Posted in
- Cases/Cooling/PSUs
- mid-tower
- Lian Li
- ATX
Noise and Thermal Testing, Overclocked
Lian Li's PC-A55 is the first time I've actually been nervous about thermally testing a case. The CPU cores were already pushing the mid-to-high 80s at stock settings under load; how was this whole thing going to fare when I bumped up the clocks and pumped more voltage through the CPU and graphics card? As it turns out, it wasn't going to fare well at all, and I'm thankful we live in an era where our hardware has thermal protections in place. Ten years ago, I likely would've had to replace most of the testbed after this.
On the charts it doesn't look as bad, but keep in mind that the Intel Core i7-2700K's cores were actually hitting 95C with the case elevated, and 98C without. The GeForce GTX 560 Ti was also peaking at 95C. All of this in a room with an ambient temperature of about 24C, a temperature which isn't terribly uncomfortable or unreasonable. If the PC-A55 had a hard time dealing with a stock system, it flat out couldn't deal with any kind of overclocking. What's worse, look at how heat builds up around the SSD and imagine what would happen if a mechanical drive were used.
Our Cooler Master Hyper 212 Evo was being pushed as hard as it possibly could and the CPU thermals were still hitting the maximum spec. The normally efficient custom cooler on the ASUS GeForce GTX 560 Ti had just as hard a time, with the fan basically maxing out under load. Lian Li's design has virtually no thermal headroom. With the elevated testbed, the GPU does better, but even so it places last out of our set of cases.
The PC-A55 basically winds up being our worst-case scenario on almost all fronts. While it remains quiet at idle, under load it's very noisy and uncomfortable to listen to, due to the fact that the fans running inside are all going at full bore. As a side note, because of the aluminum shell, the top of the case was actually almost painfully hot to the touch when tested under these conditions. Putting the case on a flat surface helped thermals a bit, but also gave noise one more place to escape, causing it to run even louder.
64 Comments
View All Comments
poloa - Tuesday, March 12, 2013 - link
They seem to have quoted the package dimensions in this review, not the case dimensions :-/ The outside dimensions are really the best feature of this case! (W) 188mm x (H) 375mm x (D) 455mmMugur - Sunday, June 17, 2012 - link
I can't see any picture at all in the article. What's wrong?cjb110 - Monday, June 18, 2012 - link
me too:(996GT2 - Sunday, June 17, 2012 - link
Anandtech has now reviewed both the A05FN and A55. However, I believe that both of these cases have inferior designs compared to the original PC-A05N. The A05N retains the inverted layout first seen in the A05A, and the back to front airflow design is arguably much better for CPU cooling. It would be nice to see a review of the older A05N to see whether Lian Li has been going downhill in their more recent designs.Leyawiin - Monday, June 18, 2012 - link
I think they are going downhill. I have an PC-A05NB with the optional 140mm top lid and its very cool running and a very clever design. These last two are pretty disappointing.Zink - Sunday, June 17, 2012 - link
When the site came back this was supposed to be Anand's review of the new Macbook. I can understand him needing a bit of sleep but save the battery rundown tests for next week and let someone remote in to your LAN to run benches.cjs150 - Monday, June 18, 2012 - link
This is based on the A05N which was a great little case if you are into watercooling, the inverted designed dealt with the airflow problem by having the GPU at the top of the case.A55 might still be a good watercooling case if you stick to micro ATX cards because the bottom of the case looks perfect for a thick 240 radiator but instead of being a simple case to use, a fair bit of modding seems to be needed.
Go back to the inverted design. Actually scrub the design and start again
piroroadkill - Monday, June 18, 2012 - link
Cut a side blowhole and the core issue is solved. Why isn't there one? what the hell..superccs - Monday, June 18, 2012 - link
I have the A05 which has the PSU up front and it the rocks rear intake and front exhaust format well. CPU gets fresh air straight from a 120mm in the rear, the GPU gets frech air from a 1200mm in the side panel and everything is blown out the front by a 120mm and the PSU.That format works great, but WTH is with this mutant case? Do case designers know that the primary goal is to have a slick looking enclosure that keeps everything cool?
Lian Li, please loose whoever designed this case in next years floods.
grave00 - Monday, June 18, 2012 - link
"In case you're not interested in a black PC-A55"Really, who wouldn't be interested in that? I think we could all use a black PC-A55.
It's like shooting the broad side of a barn isn't it?