nForce4 SLI Roundup: Painful and Rewarding
by Wesley Fink on February 28, 2005 7:00 AM EST- Posted in
- Motherboards
Gaming Performance
Wolfenstein-Enemy Territory-Radar
Doom 3
Aquamark 3
Quake 3 Arena
UT2004
Far Cry
Half-Life 2
3DMark03
3DMark05
When it was first reported that nVidia SLI supported FutureMark 3Dmark05 and 03, many gamers considered the support something of a joke. But as you can see in the benchmarks, both 3DMarks are very good at demonstrating the potential impact of SLI on gaming performance. Moving from single video to SLI increases 3DMark05 performance by almost 80%. Similarly, we see a performance increase of over 60% in 3DMark 03 when we compare results with a single video card to SLI. Aquamark 3, another "standardized" 1024 benchmark, also sees improvements with SLI, but they are much smaller than the huge performance gains in the 3DMarks.
Doom 3, Half Life 2, and Far Cry all follow patterns that we have seen in their performance since SLI was first introduced.
We purposely included a few benchmarks that we knew were not supported by current nVidia drivers to show what can happen in these games. SLI results in these non-supported games range from no improvement at all with SLI to small performance losses in Quake 3. The point is that SLI is only worth it if the game you want to play is supported by nVidia drivers. This may get a little more complicated if nVidia turns on SLI by default when the driver sees an unknown, but for now, you need a supported game for SLI to make sense.
Yes, we fully expect the new, exciting, and best-selling games that are on their way to be supported by SLI.
Facebook
Twitter
RSS
108 Comments
View All Comments
Heinrich - Monday, February 28, 2005 - link
Wesley did you spend any time at all on this link, I consider this to be a serious issue
http://www.rhcf.com/sisubb/ultimatebb.php/topic/21...
Heinrich - Monday, February 28, 2005 - link
When I set up my MSI board I cannot get surround sound out of the optical digital cable except for DVDs. I verified this on a few web sites. Not why there is conflicting information but mine is real world experience with current drivers (did not use packaged CDs)
giz02 - Monday, February 28, 2005 - link
#28, 31 and 32...The onboard Creative Sound Blaster Live! 24-bit samples at 192 KHz instead of 96 KHz (like Realtek's ALC880/880D and 850) and features full support for Creative's EAX HD technology. Additionally, the soundcard has also passed Dolby certification for Dolby Digital and Dolby Digital EX and has an integrated Dolby interactive content encoder!
Snip from PCStats review:
http://www.pcstats.com/articleview.cfm?articleid=1...
Dice Dice baby.. (couldn't resist)
giz02 - Monday, February 28, 2005 - link
#41 I've got a TT WS0049 PS, so I should be good with the -5v.#43 I've already cancled my DFI SLI DR board. MSI here I come ($238 cdn... so it's cheaper too) :D
Wesley Fink - Monday, February 28, 2005 - link
#42 - The on-board nF4 LAN requires a PHY (Physical Layer) gigabit LAN to function properly, but is specified as PCIe. All 4 SLI boards implement PCI Express Gigabit LAN with the PHY chips (Vitesse or Marvel). If you check all 4 manuals you will see Gigabit PCIe LAN specified by all 4 for the on-chip LAN.#40 - From the MSI manual Audio specifications:
"Dolby Digital Encoder. 24-bit/96-192kHz audio quality. Up to 100db SNR. 7.1 channel H/W audio."
ChineseDemocracyGNR - Monday, February 28, 2005 - link
Wesley,"all 4 SLI boards implement PCIe on Gigabit #1"
I don't think the onboard LAN on the nForce4 chipset uses the PCI-E bus, are you sure about this?
Spacecomber - Monday, February 28, 2005 - link
Here's the address for a MSI forum note concerning the problem with the Creative onboard sound and power supplies without a -5 volt connection.http://diamondclub.msi.com.tw/eng/forum/viewthread...
And, if you take a look at the ATX12V Power Supply Design Guide, you can see that the lack of a -5 volt connection on many current power supplies should not have come as a surprise to MSI.
http://www.formfactors.org/developer/specs/ATX12V%...
Space
giz02 - Monday, February 28, 2005 - link
WOW! This is looking good...Manual available here:
http://www.msi.com.tw/program/support/manual/mnu/s...
Page 5-1 of the MS 7100 manual (At MSI)
CA0106
Brand new Azalia Spec
8 Channel & SPDIF audio effect
Page 5-8
After installing teh creative audio driver, you are able to use teh 2-,4-,6- or 8- channel and the SPDIF audio featre now..
Page 5-11
Decoder shows SPDIF Passthrough option!!!
I am not familiar with the old Creative Live 24 hardware or menu settings, but is this new?
giz02 - Monday, February 28, 2005 - link
BTW: If this is the case, I am canceling my DFI preorder (I've been waiting almost 1 month for this board to become available....)Good things may indeed come to those who wait! There is no better way to hook up to my Z5500's if the encode is supported!
giz02 - Monday, February 28, 2005 - link
#28, #31, I'd really like to know as well...#32, I guess this is brought up, because of this statement in the roundup (on the first MSI Page)
"The Audio also fully supports Dolby Digital encoding, which will matter a great deal to some users."
Anand, is this some sort of typo, or can the onboard solution in facte ENCODE dolby digital audio. The ENCODE assumes that it can take .wav audio and encode it to dolby digital and place it on any (analog/SPDIF Coax/Toslink) output (ala IntelHD and SoundStorm)
Let us know :D