Closed Loop AIO Liquid Coolers: 14-way Mega Roundup Review
by E. Fylladitakis on February 12, 2014 7:00 AM ESTNZXT
NZXT is another company that recently decided to jump on the AIO cooling bandwagon and they did so a little bit furiously. Instead of releasing a wide selection of products, NZXT released only two coolers, both meant for 140mm fans alone, clearly aiming for the high-performance segments of the AIO coolers market. They supplied us with both of their AIO coolers for this review.
NZXT Kraken X40
We received the Kraken X40 in a well-designed, white box with plenty of information about the product printed on its back and sides. Inside the box, the cooler is protected by cardboard packaging and nylon bags. The bundle of the Kraken X40 comes well presented, with the mounting hardware categorized into separate nylon bags. All of the mounting hardware and brackets are black. There also is a leaflet with installation instructions and a CD with the Kraken Control software, a rather simple piece of software that can be used to control the speed of the pump, fans, and the lighting of the CPU block. A single 140mm fan with a black frame and white blades is supplied with the X40. The fan has a very wide speed range of 800 to 2000 RPM and a fluid bearing for high performance and reliability.
Aesthetically, the Kraken X40 is hardly any different from most other Asetek designs. NZXT went with the normal thickness (27mm) on a 140mm wide radiator, most likely to ensure the compatibility of the cooler with most of their cases. The radiator follows the standard design of every other Asetek-made AIO cooler to this date, with wavy aluminum heat dissipation fins soldered on to the liquid pass-through channels. Unfortunately, fin deformations and imperfections are once again common. NZXT is using black, kink resistant tubing made of hard, smooth rubber. It is noteworthy to mention that the Kraken X40 has 16" (40cm) long tubing, which is about 4" (10cm) longer than that in most other kits.
The circular block-pump assembly does look like the standard Asetek designs, such as the ones of the Corsair H90/H110 kits, yet there is more to it than first meets the eye. There are many wires coming in and out of the block; one is a 3-pin header for power, one is for the USB interface, and the third is for the connection of up to two fans. If the fans are to be controlled via NZXT's Kraken Control software, they need to be connected to the block. NZXT is confident that all of these can be powered via a single 3-pin fan header. At the top of the block, covered by a sticker that is a pain to remove, a circular ring with NZXT's logo on the side can be seen. There is not one but several LED lights beneath it, allowing full control of its lighting color via the supplied software. It is also possible to adjust the color according to the temperature. However, the pump will not light up until it receives a command from the software, so do not get concerned if there is no lighting when you first start up your system.
NZXT Kraken X60
The Kraken X60 essentially is the bigger brother of the X40. It comes supplied in a similarly designed cardboard box, just a little bit larger and with thicker packaging material inside. The bundle is virtually identical, with the same black mounting hardware and a similar manual with installation instructions. However, two 140mm fans are now supplied with the cooler, the same 140mm fans with the black frame and white blades as the one supplied with the X40.
Essentially, the Kraken X60 is both technically and visually identical to the X40, with the exception of the radiator, which is twice as long. The 280mm long radiator can now support up to four 140mm fans, with two supplied by NZXT. Other than that, it has the exact same width and thickness as the radiator of the X40, as well as the same issues with the quality of the heat dissipation fins.
The block-pump assembly is very similar to that of the X40 as well, featuring the same circular design and the same multi-color LED lighting. There are differences on the wiring though, as the assembly now requires power from a SATA connector and can be used to control up to four fans. It appears that the pump is still being powered by the 3-pin header, allowing the control of its speed by the motherboard, with the SATA connector reserved for powering the USB interface and the fans. Thermal compound has been pre-applied on the copper base of the cooler, which is machined to a nearly perfect finish.
Facebook
Twitter
RSS
139 Comments
View All Comments
E.Fyll - Wednesday, February 12, 2014 - link
It would not; even pure distilled water becomes conductive once it comes in contact with dust. None of these coolers are using pure distilled water anyway, all are using a mixture, which is conductive. It has lower conductivity than mineral water, yet it is conductive. The higher the portion of the additive over the distilled water, the more conductive the solution becomes. The actual level of conductivity also depends on the additive, some are more conductive than others. However, it should suffice to say that the least conductive additive at the lowest possible concentration would still be extremely dangerous to electronics.I will summarize: If it leaks, you are doomed.
Dustin Sklavos - Wednesday, February 12, 2014 - link
"If it leaks, you are doomed" is a little alarmist. It depends on where the product leaks and how large the leak is. The cooler itself certainly isn't usable anymore if it's leaking, but we get hardware in from time to time for leak damage that actually works perfectly fine (Corsair warrants your hardware against cooler leaks).E.Fyll - Wednesday, February 12, 2014 - link
Yes, I possibly over-exaggerated there. What I wanted to stress is that the liquid is definitely conductive, not that it will cause permanent damage 100% of the time. There is a high chance that the hardware will be damaged but that is definitely not always the case. I myself had a serious (nearly 1/4 liter) leak with a custom-made setup and the system was just fine once it was dry again.jrs77 - Wednesday, February 12, 2014 - link
Enermax and Silverstone use quiet possibly Swiftech as a supplier for their AIO-blocks.And btw, you should've really integrated the Swiftech H220 into your roundup.
E.Fyll - Wednesday, February 12, 2014 - link
I know. I actually tried to acquire all AIO coolers in existence, including Intel's, Thermaltake's and others. Not everyone is happy to cooperate and/or willing/able to supply samples at a give time, for whatever reason.toyotabedzrock - Wednesday, February 12, 2014 - link
We need a roundup of fans. I have bought many expensive fans that turned out to be less than advertised and failed quickly when used in certain orientations. Even had blades break.E.Fyll - Wednesday, February 12, 2014 - link
That is going to happen, eventually. I need proper equipment to properly test fans. Until I can acquire it, I will not perform a half-assed job.HisDivineOrder - Wednesday, February 12, 2014 - link
It's reprehensible that you guys are not reviewing the Swiftech option that allows you to use the closed AIO part or switch to a more open config if you like, too.If you say, "That's because it's not on the market now!" I'll say it's because of Asetek trying to basically own the market and are using litigation to destroy competition. Was it any wonder that when the Swiftech was on the market, we had Corsair and NZXT AIO's all dropping down to sub-$100 for even their highest of the high end? The value you got for that $130-140 was so outstanding, no one would touch a single one of these coolers.
So to my eye, I don't see why you'd bother reviewing such subpar products that are at ludicrous pricing and reward Asetek and their twin from another mother for not bothering to compete.
Not going to reward patent trolls.
E.Fyll - Wednesday, February 12, 2014 - link
Copy-paste from above:"I know. I actually tried to acquire all AIO coolers in existence, including Intel's, Thermaltake's and others. Not everyone is happy to cooperate and/or willing/able to supply samples at a give time, for whatever reason."
I cannot test what I cannot have access to. I would love to test Swiftech's products but the company needs to be willing to ship me samples first.
Dustin Sklavos - Wednesday, February 12, 2014 - link
"Reprehensible" is an awfully strong word, isn't it? There's a lot of logistics that go into just trying to put together a roundup like this, and respectfully, you don't have the full picture of Asetek's patent or what's going on in the AIO market.