MSI Z77A-GD65 - Overview

Whenever it comes to a motherboard comparison involving ASUS, Gigabyte or ASRock against an MSI board, the MSI board always tends to show a strong result - either in terms of price, performance or features.  Therefore, when it comes to the new batch of motherboards for Ivy Bridge, it is fair to say that I expect a strong showing from MSI.  Today, we have their Z77A-GD65, which will be one behind their future released GD80 that got attention back at CES for being Thunderbolt equipped.

The Z77A-GD65 currently retails at $190, a good amount above the Gigabyte board.  With the MSI, we have an Intel NIC, a full set of audio outputs, but no PCI or mSATA.  The Z77A-GD65 is in general a good board to play with.  It would underpin any Z77 build with ease.  The design is beneficial to multi-GPU setups, offers voltage read points of overclockers, and gives a front facing USB 3.0 port for front panel USB 3.0 cases.  The auto-overclocking OC Genie is relatively simple, but using the BIOS is straightforward (either at boot time or in the OS with Click BIOS software) to get something more befitting an Ivy Bridge processor.

Due to some of the other boards providing an overclock out-of-the-box, performance on the MSI may seem to be a little down on the other boards, but by enabling OC Genie on board, which every processor should be able to do, performance numbers would be comparable to the competition.

Visual Inspection

The Z77A-GD65 is another motherboard in this roundup that comes in a black and blue livery.  This time MSI have more of an excuse than others do as they have been using it for a fair while now.  Using what is essentially a 10 + 2 phase power delivery, MSI are using somewhat beefier heatsinks than their rivals, connecting both via a heatpipe.  The socket area is right up against Intel's minimum requirements from left to right, but there is some room to maneuver big air coolers from top to bottom.  Around the socket there are at least four fan headers to use: one 4-pin CPU header between the top VRM and the memory slots, a 4-pin system fan header just the other side of the memory slots, a 4-pin to the bottom left of the socket area, and another 4-pin beside the 24-pin ATX power connector.   A fifth fan header can be found at the bottom of the board.

Along the right hand side, we have the standard MSI trio of power/reset/OC Genie buttons, followed by a series of voltage checkpoints for overclockers.  Aside from the 24-pin power connector and the system fan header, there is also a USB 3.0 header at right angles to the board, indicating its primary use is to the front of the case.  Underneath this are the eight SATA ports - two SATA 6 Gbps from the PCH, four SATA 6 Gbps also from the PCH, and another two SATA 6 Gbps from an ASMedia controller.

As the power/reset/OC Genie buttons are at the top right, the bottom of the board has more room to fit in all the headers as needed - front panel audio, TPM, front panel headers and USB 2.0 headers.  In terms of PCIe, MSI have done away with the PCIe to PCI bridge and focused purely on PCIe.  We have an x1, x16 (x8 with dual GPU), x1, x1, x8, x1, and a PCIe 2.0 x4.  In this instance, there is plenty of room for a dual GPU setup with PCIe slots to spare for any extras.

Also of note is the chipset cooler, which is very flat and large with minimal fins, perhaps suggesting that MSI is confident about their heatsink design.  Underneath this is a two digit debug display, and a BIOS switch for changing between two BIOSes.

On the rear IO panel, I think MSI have been reasonable with what they have left in and what they have left out.  From left to right, we have a combination PS/2 port, two USB 2.0 ports (black), a clear CMOS button, digital and coaxial SPDIF outputs, two more USB 2.0 ports (black), a HDMI port, gigabit Ethernet, two USB 3.0 ports (blue), D-Sub, DVI-D, and audio jacks.

Board Features

MSI Z77A-GD65
Price Link
Size ATX
CPU Interface LGA-1155
Chipset Intel Z77
Power Delivery (CPU/iGPU) 8 + 1 + 2 + 1 (VRM/VTT/GPU/SA)
Memory Slots Four DDR3 DIMM slots supporting up to 32 GB
Up to Dual Channel, 1066-2667 MHz
Video Outputs HDMI, DVI-D, D-Sub
Onboard LAN Intel 82579V
Onboard Audio Realtek ALC898
Expansion Slots 2 x PCIe x16 Gen3 (x16, x8/8)
1 x PCIe x16 Gen2 (x4)
4 x PCIe x1 Gen2
Onboard SATA/RAID 2 x SATA 6 Gbps (PCH), Support for RAID 0, 1, 5, 10
4 x SATA 3 Gbps (PCH), Support for RAID 0, 1, 5, 10
2 x SATA 6 Gbps (ASMedia ASM1061)
USB 4 USB 3.0 ports (2 back panel, 2 from headers)
10 USB 2.0 ports (4 back panel, 6 from headers)
Onboard 4 x SATA 6Gbps
4 x SATA 3 Gbps
1 x USB 3.0 Header
3 x USB 2.0 Headers
1 x IEEE1394 Header
1 x TPM Header
1 x Front Panel Audio Header
Power/Reset Buttons
OC Genie
5 x Fan Headers
Power Connectors 1 x 24-pin ATX connector
1 x 8-pin 12V connector
Fan Headers 1 x CPU Fan Header (4-pin)
4 x SYS Fan Headers (two 4-pin, two 3-pin)
IO Panel 1 x Combo PS/2 Port
1 x Clear CMOS Button
1 x Coaxial S/PDIF Port
1 x Optical S/PDIF Port
4 x USB 2.0
2 x USB 3.0
1 x Gigabit Ethernet
Audio Jacks
1 x HDMI
1 x DVI-D
1 x D-Sub
Warranty Period 3 Years
Product Page Link

It is good to see an Intel NIC on this motherboard and plenty of headers to go around.  The only things missing where other motherboards may have better all-round functionality are a PCI slot, mSATA or on-board WiFi.

 

Gigabyte GA-Z77X-UD3H - In The Box, Overclocking MSI Z77A-GD65 - BIOS and Software
Comments Locked

117 Comments

View All Comments

  • drbuzbee - Thursday, May 10, 2012 - link

    The Lan read and write sequential speeds are labeled MBytes ps but undoubtedly are reported in Mbits ps.
  • millisec - Thursday, May 10, 2012 - link

    The Gigabyte UD3 is a nice board but it's a little annoying that's the board GB keeps sending out for reviews because of the $160 price mark. For $29 more you get so much more in the UD5 with Realtek audio, dual lan with Intel/Atheros, PCI 3.0 X4 slot, more sata 3 ports and second Marvell raid controller. The extra $29 buys a lot vs. the UD3 and in IMO is a much better value. Just hoping the UD5 arriving today does not have the same problems with the G.Skill Ripjaws X 2400 kit Anand had. Won't be a happy camper...
  • Zoomer - Tuesday, May 15, 2012 - link

    $29 for extra sata ports = pass. ;)
  • embeddedbill - Friday, May 11, 2012 - link

    Hi Ian, any chance you will have an update on this board?
  • embeddedbill - Friday, May 11, 2012 - link

    What... Did that take about 3 minutes from this question to Anands article?
  • smalM - Friday, May 11, 2012 - link

    Black connectors, video ports, PS/2 - the first manufacturer who omits all that nonsense will get my money.
  • KivBlue - Friday, May 11, 2012 - link

    Gigabyte has gone cheap for sure, I have compared the specs for both on-board audio chips and Realtek clearly has more feature sets. Plus VIA interface looks hideous. My current system's motherboard is Gigabyte and while they have improved things with UEFI, the feature set they have in it is pretty much the same as the old BIOS, ASUS clearly has a more comprehensive UEFI in that regard, I would go with ASUS motherboard in the future as I'm no longer a novice and someone who wants to take full control of a system.
  • bobster1 - Sunday, May 13, 2012 - link

    I've been debugging crashes at stock and overclock for a few days and finally seem to have found the cause, and thought it was worth mentioning here as I didn't see anything about it in the article.

    I was finding my 7970 crossfire/UD3h/3770k setup was locking up frequently in games like the Witcher 2 - the system would freeze and had to be turned off and on again. I discovered by accident that the games became stable if I had prime95 running in the background, and eventually concluded that it must have something to do with the voltages at lighter loads. When I bumped up the voltage to 1.25v in the BIOS (using the static setting, rather than dynamic voltage), it seems to have solved the problem. I'm guessing this is due to Ivy Bridge taking responsibility for pci-e; it's rather unfortunate as it means I can't let the cpu use a lower voltage in an idle state without it rendering the system unstable when rendering 3d.
  • mikeyd55 - Tuesday, June 19, 2012 - link

    Hi,

    First, thank you for addressing this important benchmark!

    Your article notes that POST times can be improved by disabling non essential controllers.

    It would be helpful to know, with the minimum controllers enabled to support a system built on either the PRO or DELUXE (Asus) boards, with: one NIC enabled in OS (only?), boot from one SSD and/or one optical drive connected to Z77 chipset ports (no third party storage controller needed), USB disabled on boot, but enabled in OS (if possible as with certain Intel boards?), and any Wireless option disabled, what could be expected.

  • Conditioned - Wednesday, June 20, 2012 - link

    So how was dpc measured? If you disable intel-c state and all other powersaving features it makes an absolutely huge difference in dpc.

Log in

Don't have an account? Sign up now