Rosewill Ranger: All About Compromising
by Dustin Sklavos on December 14, 2011 12:10 AM EST- Posted in
- Cases/Cooling/PSUs
- mid-tower
- Rosewill
Noise and Thermal Testing, Stock
However many misgivings I may have about the build and design of Rosewill's Ranger, it can probably be forgiven if the thermal performance and acoustics are there. While I don't have much faith in it keeping a low noise profile (given the amount of ventilation in the design), there's still a chance it could produce excellent thermals.
As it turns out, the Ranger's thermals are absolutely stellar, placing at or near the top of the charts in every discipline at our stock settings. The tight case design could very well be paying off as the air is fairly directed.
Unfortunately, idle noise isn't so hot, though load noise is mostly on par with our other entrants. Enclosures in this market segment tend not to have much in the way of the soundproofing, and the one that does (the NZXT H2) has a design flaw that negates any advantages there. We're not using components that would be good for a "silent" build regardless, and the Ranger at stock settings is at least decent. What about when we crank up the overclock?
Facebook
Twitter
RSS
33 Comments
View All Comments
Iketh - Wednesday, December 14, 2011 - link
IIIIIIIII find this hard to believe... motherboards have plenty of flexShieTar - Wednesday, December 14, 2011 - link
Sure, but operating them while bent, with maybe some thermal cycling on top, does not sound like a good Idea.Of course, if the routing is this bad, why not just leave it be and live with the cables within the case, like it has been done with any case before 2008 or so. I'd rather have a somewhat uglified interior and a slightly disturbed airflow, rather than turn assembly into a comical "You sit on it, I close it" episode.
piroroadkill - Wednesday, December 14, 2011 - link
Oh, I got a new case, Fractal Design Define R3, now, and made sure to bear this fact in mind.My system is OK now, although I do have a new board.
piroroadkill - Wednesday, December 14, 2011 - link
Well, you can find it hard to believe, but when I was about to fit a new motherboard, I unscrewed my old one, took it out, put my brand new one in, and noticed there was a gap of about 4mm or something silly between the motherboard and the standoffs near the bottom of the case.I had to push the crap out of the tray to get it back to flat, so the motherboard would actually sit flat on all the standoffs.
My old motherboard had clearly been bent by the motherboard tray. I'm not sure why that's unbelievable.
kyuu - Wednesday, December 14, 2011 - link
I believe what the poster found hard to believe was that the motherboard flex was the cause of your issues, not that the tray was in fact bent and, therefore, flexing your mobo. Although, usually the side panel of the case will bend outwards rather than pushing the motherboard try in, since it is generally going to be a lot more flexible than the tray.I would have to concur with that poster, unless there was really an extreme amount of flex going on with your mobo.
However, I would concur that case manufacturers really need to provide enough space to actually route cables behind the tray and enable the side panel to go without an overt amount of force and/or bending the side panel out.
IvanChess - Wednesday, December 14, 2011 - link
I own the Rosewill Gear X3 and it has lots of plastic and it uses a pass-thru cable instead of a motherboard header for the USB 3.0 (my motherboard doesn't have that so no big loss and you can buy a converter) but it was actually a nice build for under $50 at the time. Lot's of room inside and behind the motherboard tray plus it has a hole for the ATX CPU power cable at the top of the case. The top fans are mounted in plastic outside the case which looks terrible but keeps the inside roomy. In conclusion, the case looks cheap and is cheap but it is very functional especially if you replace the fans and add a fan controller.DanNeely - Wednesday, December 14, 2011 - link
I picked one of those up during the sale too to give my 2ndary box a case that wasn't an exercise in frustration/impossible to get a full size GPU in. The Gear x3's plastic has just a hint of gloss but is much more heavily skewed toward matte. Cable space was a bit tight; but as long as you use right angle sata connectors and make sure none of the fat cables are overlapping the panel goes on reasonably easily.IvanChess - Friday, December 16, 2011 - link
The plastic is mostly matte but it is a different black from the rest of the case so it looks weird. Also, I should have said the case has plenty of room for cables given the price tag although using right angle SATA connectors I did fit three drives into the case without much problem and zip-ties (with handy tie down points built-in to the case) can really compress the cables so they fit into that channel behind the motherboard.mfenn - Wednesday, December 14, 2011 - link
"The routing holes around the motherboard tray are seeming slightly off center, especially around the side-mounted SATA ports, but your mileage may vary; side-mounted SATA ports on a full-sized ATX board are going to result in serious cable bending."Dustin, here's PROTIP for you: Other motherboards exist in this world besides the P7P55D-E Pro. Many of them even have 90 degree SATA ports in different locations! Interesting concept, I know.
Dustin Sklavos - Wednesday, December 14, 2011 - link
"Your mileage may vary."Stunning, I know.