DFI LANParty nF4 SLI-DR: Features and Layout

 Specification  DFI LANParty nF4 SLI-DR
CPU Interface Socket 939 Athlon 64
Chipset nForce4 SLI (single chip)
BUS Speeds 200MHz to 456MHz (in 1MHz increments)
PCI/AGP Speeds Asynchronous (Fixed)
PCI Speeds 100MHz to 145MHz in 1MHz increments
Core Voltage Auto, 0.8V to 1.55V in 0.025V increments (Normal) PLUS
*104%, 110%, 113%, 123%, 126%, 133%, 136% (Special - to 1.85V)
CPU Startup Voltage Startup, 0.825V to 1.550V in 0.025V increments
DRAM Voltage 2.5V to 3.2V in 0.1V increments (3V jumper)
2.5V to 4.0V in 0.1V increments (5V jumper)
Chipset Voltage 1.5V, 1.6V, 1.7V, 1.8V
Hyper Transport Ratios Auto, 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0
LDT Bus Transfer 16/16, 16/8, 8/16, 8/8
LDT Voltage 1.2V, 1.3V, 1..4V, 1.5V
CPU Ratios Auto, 4x to 25x in 0.5x increments
Cool'n'Quiet MAX FID Auto, 8.0 to 13.0 in 0.5x increments
DRAM Speeds Auto, 100, 120, 133, 140, 150, 166, 180, 200
Memory Command Rate Auto, 1T, 2T
Memory Slots Four 184-pin DDR Dual-Channel Slots
Unbuffered ECC or non-ECC Memory to 4GB Total
Expansion Slots 2 x16 PCIe Slots
1 x4 PCIe
1 x1 PCIe
2 PCI Slots
SLI Setup Six 16-pin Jumper Blocks
Onboard SATA 4-Drive SATA 2 by nF4 PLUS
4-Drive SATA by Sil3114
Onboard IDE Two Standard nVidia ATA133/100/66 (4 drives)
SATA/IDE RAID 4-Drive SATA 2 PLUS
4-Drive IDE (8 total)
Can be combined in RAID 0, 1
PLUS 4-Drive SATA by Sil3114
Sil3114 Raid 0, 1, 5
Onboard USB 2.0/IEEE-1394 10 USB 2.0 ports supported nF4
2 1394A FireWire ports by VIA VT6307
Onboard LAN Dual Gigabit Ethernet
PCIe by Vitesse VSC8201 PHY
PCI by Marvel 88E8001
Onboard Audio Karajan Audio Module
based on Realtek ALC850 8-Channel codec with 6 UAJ audio jacks, CD-in, front audio, and coaxial SPDIF In and Out
Other Features Power and Reset momentary switches
BIOS Award 2/17/2005 Release

The DFI boards all support the full range of nVidia nForce4 features including nVRAID, Active Armor, SATAII 3Gb/s drives, NCQ, any-drive IDE/SATA Raid, PCIe Gigabit LAN by a PHY Ethernet chip (plus an additional PCI Gigabit LAN), and the nTune utility.

Packaging for the full LANParty nF4 SLI-DR is typical LANParty.

It is a huge package with a motherboard, UV cables, a system carrier, a Front-X box, and even UV sheathing for your system cables.

DFI has continued with the Karajan Audio Module first introduced on their LANParty 925x. As you will see later in our audio tests, the Karajan module was a much better performer than what we expected when we first saw the onboard Realtek 850 codec. We still wish that DFI had been able to use the High Definition ALC880 or a similar chip instead of the more common ALC850. However, the Karajan Module on the DFI SLI does provide the lowest CPU overhead that we have seen on any board using the 850.

The ALC850 Codec provides four pairs of stereo outputs, with 5-Bit volume controls and multiple stereo and mono inputs, along with flexible mixing, and gain and mute functions. Two 50mW/20ohm headset audio amplifiers are integrated at Front-Out and Surround-Out, and both amplifiers are selectable for Front-Out, Line-In and Mic-In as a Universal Audio Jack.

You can find more information on the ALC850 at Realtek.

DFI provides a full selection of rear I/O ports. These include 6 programmable audio mini jacks plus coaxial SPDIF in and out connectors to support the Realtek ALC850. The back panel also includes PS2 mouse and keyboard, 1 standard Firewire (IEEE1394a), 6 USB, and two RJ45 Gigabit Ethernet. There are no rear ports for a Parallel Printer or serial devices, but there is an onboard header for an external serial device an IR header.

On "R" models, like the DFI LANParty nF4 SLI-DR, DFI uses the Silicon Image 3114 SATA controller to add 4 more SATA ports to the 4 already provided by the nVidia nForce4 chipset. The Sil3114 ports can be combined in RAID 0, 1, or 5. RAID 5 can be implemented on this controller with 3 hard drives.

The four DIMM slots support up to 4GB of up to DDR400 memory in a Dual-Channel memory configuration. Dual-Channel 1 is DIMMs 1 and 3, and Dual-Channel 2 is DIMMs 2 and 4. DFI specifies support for both ECC and non-ECC unbuffered memory. Contacts at DFI advise that best overclocking is achieved with the dual-channel DIMMs in Sockets 2 and 4.

Board Layout

The DFI LANParty nF4 SLI-DR is very well arranged, with almost everything located where it works best. As you will see if you study the layouts of the other SLI boards, the DFI differs substantially in layout.

The DFI nF4 place the CPU in the top center of the board and DIMMs at the top. This arrangement worked well in our testing and should work better (for those who change memory frequently) than in the crowded right-hand alternate location used on many boards.

The ATX 24-pin and the 4-pin 12V connector are in ideal locations on the DFI SLI. The 24-pin ATX is located on the preferred top right edge of the motherboard, and the 4-pin 12V power connector is right beside it. This board edge location keeps bulky cables away from the CPU and memory.

There is plenty of room around the Socket 939, so most Heat sink/Fans should work fine. A Zalman 7000 overhung DIMM slot 4, but it still cleared our stock OCZ memory and memory could work in all slots.

The IDE connectors are at our preferred upper right edge of the motherboard, and the floppy connector is a board edge connector located on the right edge around the middle of the board. Both locations worked well in our testing.

SATA connectors are to the right of the nF4 chipset and the magnetic levitation fan. The fan is low enough for video cards - both ATI and nVidia - to mount properly. We tried both ATI and nVidia top-of-the line cards to make sure.

Other SLI boards use a simple card edge that is reversed for SLI operation. DFI uses 6 16-pin jumper blocks that must all be moved to switch to SLI mode. We complained about the pin blocks in our review of the DFI SLI, but after working with the card edge boards, they are no better than the pin blocks. The tiny PCB's are hard to align on the other boards and the holding mechanisms are not always easy to negotiate. Neither solution, a card or pins, is really easy to change, so it is fortunate that end-users will rarely need to change positions of the normal/SLI switching.

Asus A8N-SLI Deluxe: Overclocking and Stress Testing DFI LANParty nF4 SLI-DR: Overclocking and Stress Testing
Comments Locked

108 Comments

View All Comments

  • eva2000 - Monday, February 28, 2005 - link

    whoops no mention of psu was used in system config listing but didn't read till page 20 of the review it mentions OCZ 520W PS psu heh
  • Slaimus - Monday, February 28, 2005 - link

    They used a OCZ 520W.
  • neologan - Monday, February 28, 2005 - link

    I think the test results for 3dmark2003 single and SLI are the wrong way around?

    http://www.anandtech.com/mb/showdoc.aspx?i=2358&am...
  • F4810 - Monday, February 28, 2005 - link

    Why did they show no benchmarks with the mobo's overclocked? It doesnt make sense to say these boards are better becuase you can clock the memory higher if the overall CPU clock is roughly the same. The reason they dont show you is that due to the onchip memory controller on the AMD chips, the high memory frequency doesnt make much of a difference at all in real world terms. As long as you can clock the CPU high that is all that really matters. Also they dont take into account cost as some boards cost 50% more that the others.
  • dornick - Monday, February 28, 2005 - link

    I was considering jumping on the SLI bandwagon until I had some sense knocked into me.

    I'd like to see a comparison of the Ultra chipset MBs, including the Chaintech, Epox, etc... since that's where I think the nForce 4 market will go.
  • eva2000 - Monday, February 28, 2005 - link

    missing one vital piece of info, what PSU you used hehe
  • Spacecomber - Monday, February 28, 2005 - link

    Thanks for doing the indepth analysis of this new chipset and how it is being implemented by some major motherboard manufacturers.

    There was one detail that I was hoping to see some reference to. I understand, from a friend, who has the MSI SLI motherboard, that the Creative Live sound chip only works if your power supply has a -5 volt connector on it. It looks to me like the OCZ power supply that you used has this, but many of the new power supplies, such as the Enermax v2.0 power supplies, no longer have a -5 volt connection. He was using a Enermax 535 watt Whisper II (SLI ready) when he ran into this issue. This kind of compatability problem slipping through QA seems like another indication that the everyone was in a big hurry to get these motherboards to market, maybe before they were thoroughly tested.

    Space
  • Regs - Monday, February 28, 2005 - link

    I liked the subtle hints Wes.

    In your final words you stated, "If you want the best performance possible then the answer would likely be yes". Then how would this apply for users getting two 6600GTs?
  • xsilver - Monday, February 28, 2005 - link

    great article
    minor gripe -- the overclocking "graphs" are useless -- what would be better is the resulting fps of overclocking to show people if its worth it to get that extra xxx fps
  • arfan - Monday, February 28, 2005 - link

    now i am waiting ultra mobo benchmark. What about the price of all this mobo ? i fell disappointed with msi doesn't have PCI 1x. (Sorry my english language is very bad)

Log in

Don't have an account? Sign up now