Gigabyte K8NXP-SLI: Overclocking and Stress Testing

FSB Overclocking Results

Front Side Bus Overclocking Testbed
Gigabyte K8NXP-SLI
Processor: Athlon 64 4000+
(2.4GHz, 1MB Cache)
CPU Voltage: 1.55V (default 1.50V)
Cooling: Thermaltake Silent Boost K8 Heat sink/Fan
Power Supply: OCZ Power Stream 520W
Memory: OCZ PC3200 EL Platinum Rev. 2
(Samsung TCCD Memory Chips)
Hard Drive: Seagate 120GB 7200RPM SATA 8MB Cache
Maximum OC:
(Standard Ratio)
230x12 (4X HT, 2.5-3-2-7, 1T, 2.8V)
2760MHz (+15%)
Maximum FSB:
(Lower Ratio)
230x12 (2760MHz) (4X HT, 2.5-3-2-7, 2.8V)
(1:1 Memory, 1T, 2 DIMMs in DC mode)
(+15% Bus Overclock)

After the excellent overclocking results that we found in our pre-production review of the K8NXP-SLI, we really expected the Gigabyte SLI to be near the top of our overclocking charts. However, something has happened along the way from pre-production to production because our production board could only reach a very disappointing 230 CPU speed regardless of the multiplier selected. This is in stark contrast to the 284 that we easily reached on the pre-production board.

We recently met with Gigabyte to discuss this issue and Gigabyte has assured us that they will make updates to get overclocking back to the levels which we saw in our earlier review. For now, we can only say that we have no idea what you will actually find in the overclocking capabilities of a K8NXP-SLI that you might buy. It could be stellar, like the pre-production board that we tested, or mediocre, like the last board that we tested. We have evidence to support either conclusion.

Memory Stress Test Results:

Our memory stress tests measure the ability of the K8NXP-SLI to operate at its officially supported memory frequency (400MHz DDR), at the lowest memory timings that OCZ PC3200 Platinum Rev. 2 modules will support. All DIMMs used for stress testing were 512MB double-sided (or double-bank) memory. To make sure that memory performed properly in Dual-Channel mode, memory was only tested using either one dual-channel (2 DIMMs) or 2 dual-channels (4 DIMMs).

Stable DDR400 Timings - One Dual-Channel
(2/4 DIMMs populated)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 2T
RAS Precharge: 7T
Precharge Delay: 2T
Command Rate: 1T

Using two DIMMs in Dual-Channel 128-bit mode, the memory performed in all benchmarks at the fastest 2-2-2-7 timings, at default 2.6 voltage.

Tests with 4 DS DIMMs on an AMD Athlon 64 system are more demanding, since AMD specifies DDR333 for this combination. However, most AMD Athlon 64 motherboards combined with recent AMD processors (the memory controller is on the AMD CPU) have been able to handle 4 DIMMs at DDR400.

Stable DDR400 Timings - 4 DIMMs
(4/4 DIMMs populated)
Clock Speed: 200MHz
CAS Latency: 2.0
RAS to CAS Delay: 2T
RAS Precharge: 7T
Precharge Delay: 2T
Command Rate: 2T

Tests with all four DIMM slots populated on the Gigabyte required a 2T Command Rate with 4 DIMMs in two dual channels. This is the pattern seen on other top-performing Socket 939 boards. There was no problem running 4 DS DIMMs at DDR400 at the same aggressive 2-2-2-7 settings, which worked well with 2 DIMMs.

Gigabyte K8NXP-SLI: Features and Layout MSI K8N Neo4/SLI Platinum: Features and Layout
Comments Locked

108 Comments

View All Comments

  • fozzymatic - Tuesday, March 1, 2005 - link

    "So, is SLI worth the cost and the effort? For some, the answer will be a definite no. The SLI boards still cost a great deal, setting up the system is still a daunting task, and the cost of two top-of-the-line video cards will be just too much for many to consider SLI to be a real option."

    I still do not understand why this argument is so popular. Why is the general assumption that purchasers of SLI capable boards will immediately want to jump into a dual-card config? The idea is flexibility. Sure, 2 6800's are expensive now, but they will inevitably get cheaper. So why not buy one now and then profit form your forward thinking later down the line when the price of a second card is cut in half and there are more SLI-supported games available. I concede that the mobos are 50$ more than a non-SLI board but, for 50$, I'll take the enhanced upgrade path. Out of the gate the SLI boards are the fastest single or double-card NF4 mobos available, so whats to lose?
  • justly - Monday, February 28, 2005 - link

    Wesley, well done, although I have to admit I skipped over some of the pages describing the individual boards as I am not personnaly intrested in buying a SLI system.

    One thing about the bar graphs, it could have been a little easier to compare between a single card and SLI if you had used split bars like in this graph
    http://images.anandtech.com/reviews/video/ATI/rade...
    using the top half of the bar for single card and the bottom for duel cards.

    It would also be nice to see a comparasion of disk controller, firewire and USB performance (and anything else that is chipset specific) using all the different brand chipsets.

    I don't think you are the person that does power supply reviews, but with all the concerns recenty about power supplies it would also be nice to see an article that not only describes some of the differences in power supplies but what components draw power from what rails and how much they draw (I have seen power supply guides that give an idea of how many total watts is needed but very little information on how those watts are divided up between rails).

    One last thing, I have a little problem with this statement "the ability of a motherboard to run at much higher than stock speeds tells you something about the quality of components used in a motherboard". If every motherboad had a perfect BIOS and they all had the same overclocking options then your statement could be true, but that is not the case. Would you call all Intel branded motherboards poor quality just because Intel doesn't put overclocking options in their motherboards BIOS? What if an OEM decided to use one of these great overclocking boards in a prebuilt system and the only change they made to the board was to eliminate the overclocking options from the BIOS, is that board now poor quality?


  • Viper4185 - Monday, February 28, 2005 - link

    Well well well, seems you are right. The MSI nForce 4 Ultra board in Australia even has 1x PCI Express slot...

    http://www.msi.com.tw/program/products/mainboard/m...

    Does anyone know which boards support Firewire 800 (1934b)?

    Also to Wesley, thanks for the reply, do you have a rough idea when the nForce 4 Ultra comparison would be available?
  • falcc - Monday, February 28, 2005 - link

    There seems to be different version of MSI's SLI boards depending on where you live. In Australia the SLI board is a MSI K8N Diamond. The interesting thing about this board is that it has two PCI Express x1 slots. as well as the two x16 slots for SLI. It also has a wlan option.
  • falcc - Monday, February 28, 2005 - link

  • ChineseDemocracyGNR - Monday, February 28, 2005 - link

    #43, I'm aware it needs a PHY, but I always thought it worked the same way as it did since the nForce3-250Gb, with no PCI-E involved.

    I checked out the manual for the MSI K8N Diamond and ASUS A8N-SLI, from them:

    MSI
    "Dual LAN
    ? Supports dual LAN jacks
    - 1st LAN supports 10/100/1000 Fast Ethernet by nForce4 SLI
    - 2nd PCI Express LAN supports 10/100/1000 Fast Ethernet by Marvell 88E8053"

    ASUS
    "nForce4 built-in Gbit MAC with external Marvell PHY :
    - NV ActiveArmor
    - NV Firewall
    - AI NET2"

    I couldn't find a reference that the chipset LAN is tied to PCI-E.
  • ajmiles - Monday, February 28, 2005 - link

    Excellent, thanks Wesley. Every response I've had from now has been, quote:

    "With regards to the overclockability, it has AI Overclock, PEG link, and other options, the extent of the overclockability was not promised and unfortunately some customers expect amazing overclocking abilities when the 1T overclock is still a good feature and is overclocking in action."

    Perhaps what you would expect them to say when their board clocks more than 60mhz lower than some competitors.

    If you could keep me apprised of their response either here or at amiles(at)gmail.com that'd be great. Thanks again.
  • JoKeRr - Monday, February 28, 2005 - link

    I really wish MSI could pump a bit more voltage for the ram, 2.85 is a bit low, especially considering the Asus is giving 3V and DFI is giving 4V!! Guess if u want to run your good old BH5 sticks at 250mhz 2-2-2-7, DFI will be the way to go. But I really liked the MSI mobo. o well, guess u can't have everything.
  • JoKeRr - Monday, February 28, 2005 - link

  • Wesley Fink - Monday, February 28, 2005 - link

    #6 & #56 - I saw the same behavior with the A8N-SLI Deluxe during our testing, and I shared my results with Asus. I forwarded your comments and my own to the Asus A8N-SLI BIOS and Engineering team.

Log in

Don't have an account? Sign up now