Fractal Design Core 1000: How Little is Too Little
by Dustin Sklavos on April 13, 2012 11:35 AM EST- Posted in
- Cases/Cooling/PSUs
- MicroATX
- Mini-Tower
- Fractal Design
Conclusion: A Strange Balancing Act
Producing a good enclosure for the extreme budget sector of the market is, as far as I can tell, an incredibly difficult balancing act. There's a lot of balancing that honestly goes on with any enclosure south of $150, but the latitude you have with which to work just gets smaller and smaller, and when you eventually get down to the $40 price tag that the Fractal Design Core 1000 is sitting at, you start actually having to see if the case supports everything you specifically need.
I don't think the Core 1000 is a bad case by any stretch of the imagination, and it's definitely in the running for the smallest case you can buy at the lowest price. So if you want something small at the exclusion of virtually all else, I just don't see how you're going to beat it. The cooling system is also, at least on paper and mostly in practice, very efficient and a far cry from the old school cheapo boxes with a single sad 80mm exhaust fan in the back. Finally, the build quality is actually quite good, and Fractal Design includes a lot of trimmings that some of you may appreciate.
The problem is that I feel like those trimmings came at too high a cost, and that in a broader sense I'm just not sure the Core 1000 is competitive with more generic budget cases. Much is sacrificed to get this low, and I'm not talking about niceties, either; I'm talking about not being able to have more than two 3.5" hard drives, the one component users are most apt to keep adding over time. The difficulty of installing a full-size mATX motherboard is also a problem, and putting the I/O ports on the right side of the case is a mistake in our opinion. The only other case we've reviewed in this price bracket is the BitFenix Outlaw, which at $10 more is still a slam dunk over the Core 1000 as far as I'm concerned, unless the jump to full ATX is too much.
At $40 it's hard to necessarily go wrong with the Core 1000, and I have no doubt that some users are going to point to this case and say, "See! You don't need to spend more than $40 to get a good case!" The problem is that the Core 1000 is also difficult to work in and with even by Micro-ATX standards and it's frankly pretty noisy for higher spec components. Basically, you need to choose you components and set your expectations properly if you're in the market for this sort of system; we'd recommend a slightly smaller mATX motherboard along with a modular PSU, a modest CPU and GPU, and don't get a large tower cooler. Even then, we feel Fractal Design makes better cases that are better values, but it's like the old saying goes: you get what you pay for. If what you want is an inexpensive mATX case, the Core 1000 is worth a look; just be sure you understand the compromises made with such a platform.
Facebook
Twitter
RSS
53 Comments
View All Comments
tambok2012 - Saturday, April 14, 2012 - link
I just got this pictures from our country philippineshttp://www.tipidpc.com/viewtopic.php?tid=261886&am...
mariush - Saturday, April 14, 2012 - link
Our Cooler Master Hyper 212 Evo is by no means [..], but its 159mm height caused the tops of the heatpipes to press against the side panel, bowing it outward a little.Yeah, because someone who buys a $40-45 dollar case is obviously going to to buy a $30 cpu cooler when the retail processor come with a perfectly good stock cooler.
How out of touch can some reviewers become...
This is not a case designed for overclockers, no need for special coolers, the stock ones are fine for regular users.
The only flaw I see is the small cage. A 4-5 unit one would meet more users' needs.
stoggy - Saturday, April 14, 2012 - link
how disconnected? He is using a downward facing PS, in a top slot. That will severily reduce his ability to overclock too, extra heat.Lesson to learn, Its easier to cool more heat in a smaller space then it is to cool less heat in a greater space. Google it, check in Heating/AC, simple physics too.
Possible solutions for reviewers concerns:
1. Zip-Ties. We use to use them. Back when case mods ment saws and drills.
2. Proper Power supply
3. Grinder to lower the heat pipes, this might not be enough though, In which case i would suggest a drill. Probably with a 1/4" bit.
4. Growing a pair.
5. Have fun.
JarredWalton - Saturday, April 14, 2012 - link
"This is not a case designed for overclockers, no need for special coolers, the stock ones are fine for regular users."Speaking of being out of touch, who are you to say what a case is or isn't supposed to support? This is a review, and the point about the CPU cooler is exactly that: if you happen to be the type of user that has or plans to purchase an aftermarket cooler, the case has some cooler height limitations. That's useful information, and there are many (MANY) people that read AnandTech that are hardware enthusiasts who overclock just about every PC they own.
Your comment is pretty much exactly what we've said: if you plan on a moderate config running stock, the case will work fine. Then again, if you're doing that, just about ANY case will work fine. If we tested with the stock Intel HSF, however, we'd be adding noise and reducing cooling efficiency, all in the name of saving $30. The same people that won't want to buy a superior $30 cooler also won't want to buy an i7-2700K, or an SSD, or a GTX 560 GPU, etc. We test with a higher end setup along with overclocked settings because if that will work in a case, then everything lower spec will also work.
mariush - Saturday, April 14, 2012 - link
"...however, we'd be adding noise and reducing cooling efficiency, all in the name of saving $30"That's EXACTLY what most users buying this case did, give up features commonly found on larger cases to save 20-30$.
The stock Intel and AMD coolers are not exactly low quality ones. Users can actually perform a reasonable overclocking with them - they don't HAVE TO buy a better cooler just to overclock.
In such a small case, even with good coolers the cooling efficiency will be reduced. By the time you add a large video card and the large cpu heatsink into this case, you'll barely have any airflow at all.
So coupling this case with high performance after market cooler doesn't really make sense, and by writing it out you make it seem like a flaw, instead of something obvious.
For a real world example, why would I pay 40$ for this case, then pay 30$ for an aftermarket cooler, when I could just as well pay 60$ for an Antec Three Hundred case that comes from the start with a 140mm top fan and a 120mm side fan, has more "slots" for 120mm fans and better airflow due to the power supply being mounted at the bottom?
The Antec 300 case coupled with a stock CPU cooler will almost definitely keep the processor cooler, compared to a large cooler in a crowded Fractal Design case.
samoya22 - Sunday, April 15, 2012 - link
The Antec 300!Oh, wait...that's not the...?
UltraTech79 - Sunday, April 15, 2012 - link
I spent 29.99 at compUSA about 8 yerars ago for a better case AND it came with a freakn 250W power supply that has not exploaded and killed anyone yet! (parents low power comp)This think is pure junk. Whats with the mesh in front? Why try and get fancy with limited funds? Stick with the basics. And a vent on the side? REALLY? If you fucking have a system that needs that extra kind of cooling, you sure as fuck have the money to toss $30 more at a case.
UltraTech79 - Sunday, April 15, 2012 - link
Already found a far supirior case for 10$ more. Free shipping. Why was this ugly piece of junk even reviewed??http://www.newegg.com/Product/Product.aspx?Item=N8...
This guy is only 20$ ! And its still better!
http://www.newegg.com/Product/Product.aspx?Item=N8...
Mugur - Monday, April 16, 2012 - link
I don't think they are in the same class. Frankly I consider the case reviewed great for an inexpensive mATX build. And I'm sure that there are a lot of ugly tin and plastic 20$ cases... :-)GPCustomPC - Wednesday, April 25, 2012 - link
Does the Cooler Master Hyper 212 Evo really fit inside this case? It states 150mm of clearance and the EVO is said to be 159mm.