Well, today is a day that everyone was expecting but not the most exciting day of the month. Today, Intel officially releases the spate of 7-series chipsets for their 3rd generation Core microarchitecture processors (read—Ivy Bridge), despite the actual release of the processors being another three weeks away. This means that today we can actually look at, test, or purchase the range of motherboards that natively support Ivy Bridge. However, we can’t officially publish all the benchmarks for these products using Ivy Bridge until that date three weeks away (to be honest, we are still testing!). So today we are going to have a good in depth look into the Z77 chipset itself, and the review products we have received to let you know what we think looks good. All these boards today will be fully reviewed, warts and all, with Ivy Bridge, as close to official release as possible.

The boards today are from ASRock, ASUS, Gigabyte, MSI, ECS and Biostar. All these boards will natively support Sandy Bridge processors, and be fully upgradeable to Ivy Bridge silicon when the processors are released.

The Z77 Chipset

The important things to note about the Z77 chipset will be its differences to all things Sandy Bridge/Cougar Point, typically in relation to the Z68 platform. Rather than have a split between a chipset with video outputs and a chip without video outputs, all motherboards in the Z77 (and H77) will natively support video outputs (if the motherboard manufacturer wishes to use them). There will also not be a chipset issue as there was back this time last year with Cougar Point—so none of this B2/B3 nonsense that confused consumers.

In comparison to the previous chipsets, what we can see is simple from a table:

Chipset Comparison
Z77 Z75 H77 Z68 P67 H67
CPU Support IVB
LGA-1155
IVB
LGA-1155
IVB
LGA-1155
SNB/IVB
LGA-1155
SNB/IVB
LGA-1155
SNB/IVB
LGA-1155
CPU Overclocking Yes Yes No Yes Yes No
CPU PCIe Config 1 x16 or
2 x8 or
1 x8 + 2 x4
PCIe 3.0
1 x16 or
2 x8 PCIe 3.0
1 x16 PCIe 3.0 1 x16 or
2 x8 or
1 x8 + 2 x4
PCIe 3.0
1 x16 or
2 x8 PCIe 3.0
1 x16 PCIe 3.0
Processor Graphics Support Yes Yes Yes Yes No Yes
Intel SRT (SSD caching) Yes No Yes Yes No No
RAID Support Yes Yes Yes Yes Yes Yes
USB 2.0 Ports (3.0) 14 (4) 14 (4) 14 (4) 14 14 14
SATA Total (Max Number of 6Gbps Ports) 6 (2) 6 (2) 6 (2) 6 (2) 6 (2) 6 (2)
PCIe Lanes 8 (5GT/s) 8 (5GT/s) 8 (5GT/s) 8 (5GT/s) 8 (5GT/s) 8 (5GT/s)

Segregation is quite apparent for the consumer—a Z means you can overclock an appropriate CPU, and a ‘77’ means that you can take advantage of Intel’s SSD smart caching.

The chipset diagram above shows the layout of the Intel DZ77GA-70K motherboard, showing sixteen PCIe lanes from the processor. The astute will note that only one PCIe lane is coming from the PCH to the PCI Express Switch, which powers the PCIe to PCI bridge (and thus PCI and IEEE1394a) and the PCIe 2.0 x1 ports. This would mean that users of the DZ77GA-70K may experience bandwidth limitations when PCI and PCIe x1 devices are used.

PCIe 3.0

We still have 16 PCIe lanes from the CPU, but with the new chipset these are fully and officially rated at PCIe 3.0 speeds if you have the GPUs to take advantage of this feature. This becomes more apparent in multi-GPU setups, where the 16 lanes are split between the slots. Typically, this will be in the form of x16 for single card, x8/x8 for dual GPU, and x8/x4/x4 at tri-GPU. Having an x4 PCIe 3.0 is equivalent to an x8 PCIe 2.0, but only if you have a card that can take advantage of PCIe 3.0.

Due to this feature with the CPUs, the chipsets will have to adhere to PCIe 3.0 compliance, to deal with the transfers and lane layout design. A novel addition that we will see on many of the high-end boards is a series of onboard chips to increase the number of available lanes. These are known as PCIe 3.0 PLX PXE chips, which increase the number of lanes on the motherboard from 16 to 32—all rated PCIe 3.0. This also raises the cost of the motherboard, perhaps as much as $10-$15, so it is worth thinking long and hard if you really need that tri-GPU setup.

Native USB 3.0

The other long awaited addition found on Panther Point is the native implementation of USB 3.0 that comes directly from the chipset. The chipset will only provide two USB 3.0 headers, giving four ports total, either in the form of rear panel additions or an onboard header (this is at the discretion of the motherboard manufacturer). For many low-end boards, this eliminates the cost of a controller from the product. For high end SKUs that typically have 4-6+ USB 3.0 ports, while it does reduce the number of controllers by two, some PCB real estate will still be utilized by USB 3.0 controllers.

Memory Improvements

The Panther Point chipset comes with a few additional features that may be of benefit to some users. Partially derived from the processors themselves, the chipset now supports DDR3L thanks to its power gated DDR3 interface. This is a primary benefit for the lower end processor and chipset products (that is, all things mobile), but we will see if this moves its way into the mainstream or HTPC versions of Panther Point.

For the high-end power user, the chipset is now geared to handle memory that is more powerful. Again, thanks to the improvement on the new processors, these combined systems should be able to handle (with ease) DDR3-2800 memory. The memory dividers work similar to the gear ratios in Sandy Bridge-E, with users able to call a larger array of memory dividers than before with up to 200 MHz increments. This is of great benefit to the integrated graphics on the new generation processors, which should benefit from the purchase of a higher end memory kit to provide enough bandwidth.

We are still going to play with dual channel memory for the time being on consumer platforms. As this processor change is only a tick (process node decrease), we will have to wait for a tock or two in order for the memory subsystem to change to a larger number of channels. As seen on X58, tri-channel memory/6 slots was fairly cumbersome on motherboards, however on Sandy Bridge-E the quad channel memory (should Intel want to move in this direction) would still allow four slots on the board for an increase in memory bandwidth. However for now, dual channel it is.

If you happen to purchase ASUS for Ivy Bridge, there is also a little treat in store, as they have reworked the memory sub-system. Their new method stunned Intel engineers, but should provide distinct memory speed advantages. Simply put, instead of memory banks being read consecutively, the memory is read in parallel. We are awaiting more detail regarding how this feature works.

Power Consumption and Power Delivery

It has been well documented over the past few months that the top end model of the new processors should have a TDP of 77W. This is just shy of 50 watts less than the top models seen in Sandy Bridge-E, but more importantly, down from 95 watts as shown by the 2600K/2700K processors of Sandy Bridge. This does force a small change with the power delivery on Panther Point/Z77 products.

With less TDP to cater for, the motherboard manufacturers can spend less on the power delivery to get it to work. So there is a chance that the days of '24 phase power’ are long gone, and we will be dealing with less phases. Fewer motherboards will have dual 8-pin 12V connectors, and unless you go high end, may only require one 4-pin 12V connector to get the job done. Obviously if you apply an overclock, having access to more current (and thus more power) is of major benefit, but for the majority of system builders who will run systems at stock, this could represent savings in the construction being passed on to the consumer.

However, this does lend itself to potential issues when used in conjunction with Sandy Bridge processors—having a power delivery system less robust than Z68 could perhaps hinder Sandy Bridge overclocks.

Backwards Compatibility with Sandy Bridge Processors

To confirm what has been said in news articles around the world, the Intel 7-series chipsets will be backwards compatible with the Sandy Bridge (Intel 2nd Generation Core Microarchitecture) processors from the point of sale. All motherboard vendors should have this functionality built into their BIOSes. The beauty lies not in backwards compatibility but in releasing chipsets to take advantage of the new features—this is something AMD has done well with in the past.

In addition, a significant number of Intel 6-series chipsets (P67, Z68) should be forwards compatible with the Ivy Bridge processors, pending a BIOS update. Thus, current Sandy Bridge processor owners wishing to upgrade should make sure they have an appropriate BIOS before installing a new processor in their 6-series motherboard.

LucidLogix Virtu MVP Technology
POST A COMMENT

145 Comments

View All Comments

  • mechjman - Monday, April 09, 2012 - link

    I don't remember seeing PCIe 3.0 support straight from P6x series chipsets.
    http://www.intel.com/content/www/us/en/chipsets/ma...

    If this is regarding in use with a PLX chip, it might be good to state so.
    Reply
  • extide - Tuesday, April 10, 2012 - link

    It's actually when the boards DONT use a plx chip, or if the use 3.0 capable ones. It's only the boards that use 2.0 chips that are limited to 2.0 Reply
  • GameLifter - Tuesday, April 10, 2012 - link

    I am very curious to see how this technology will affect the overall performance of the RAM. If it works well, I may have to get the P8Z77-V Pro. Reply
  • jbuiltman - Tuesday, April 10, 2012 - link

    I am leaving my AMD FX-60, 3 GB DDR, Asus 939 Delux, Win XP, Raptor 150 HDD for IVY Bridge pasures!!!

    I am all for ASUS 16+4 power, multi usb 2.0 and 3.0 on the back panel. I also like the multiple 4 pin fan plug ins, mem ok, LED problem indicator, switches, 4 SATA 6GB connectors and heat pipes connecting the alunimum fins.

    What i want to see is 16x/16x not 8x/8x on dual video card on a Z77 board. ASUS, don't skimp for a measly $30! I hate cheap companies and don't make me think you are just being cheap!!!
    Reply
  • jbuiltman - Tuesday, April 10, 2012 - link

    Hey all you MoBo companies. Don't get cheap with the Z77 boards and not include 16x/16x on the pci-e 3.0!!!! Come on, add what you need to and pass the $30 on to me!!!! Reply
  • ratbert1 - Wednesday, April 11, 2012 - link

    "ASUS as a direct standard are now placing Intel NICs on all their channel motherboards. This is a result of a significant number of their user base requesting them over the Realtek solutions."
    Um... ASUS P8Z77-V LX has Realtek!
    and...ASUS P8H77-M PRO has Realtek!
    There are more.
    Reply
  • ratbert1 - Wednesday, April 11, 2012 - link

    I meant P8Z77-M PRO, but the H77 has it as well. Reply
  • lbeyak - Sunday, April 15, 2012 - link

    I would love a detailed review of the Gigabyte G1.Sniper 3 Z77 board when it becomes available.

    Keep up the good work!
    Reply
  • csrikant - Sunday, April 22, 2012 - link

    Dual E5-2690
    So far best i have got burn a lot $$$ to get this right
    my last build was with I7 990x got itchy in oct 2011 with some minor issue decided to change my PC got my i7 2700K did not meet my expectation
    built i7 3960x still failed many of my requirements regret my pc change from 990x
    Finally with all my pain and wasting$$ got my new build that so far perform better than my 990X build
    My advice do not get carried away by fancy new i7 release they are just little benefit for P4 just wasting time I was shocked that they released P4 with 1155 socket it was having same performace as 2700K not much change in fact it was cheaper too.

    Am not expert an average system builder but my advice from bottom of my heart is just go for E5 build if you are really looking for performace and some benefits you may spend some extra $$ on MB ,CPU,Casing etc it is worth in long run works out cheper than any fancy High end gaming rig water cooling etc all just shit tech advice. Never get ferrari performance form mod toyota.
    Reply
  • mudy - Monday, April 23, 2012 - link

    With the third pcie lane on the z77 boards I have come across almost all manufacturers saying "1xPCI Express 2.0 x16 (x4 Mode) & only available if a Gen 3 CPU are used". Does this mean that the lane is pcie 2.0 at x16 but works at pcie 3.0 x4 mode, if an IVB processor is connected, and other two pcie 3.0 lane is populated giving x8/x4x4 speed with pcie 3.0 compliant cards?? Also what will happen if I put Pcie 2.0 GPUs in the first two pcie 3.0 x16 slots and a pcie 2.0 compliant raid card (rr2720SGL) in the third pcie lane? Will it give me an effective pcie 2.0 bandwidth of x16/x8/x8 or not?? Damn these are so confusing!! I wish anandtech would do an extensive review on just the pcie lanes covering all sorts of scenario and I think NOW would be the best time to this as the transition from pcie 2.0 to pcie 3.0 will happen slowly (maybe years) so majority end-user will still be keeping their pcie 2.0 compliant devices!!

    Thanks
    Reply

Log in

Don't have an account? Sign up now