Brightness and Contrast Ratio

For those that need accurate colors, hardware color calibration is basically a given. Here, we report scores for the same areas as we did on the previous page, only this time the results are taken after we have used Monaco Optix XR Pro to calibrate the display.

Monaco Optix XR Pro

Monaco Optix XR Pro

Monaco Optix XR Pro

The most significant changes from calibration come in the area of brightness, where all of the displays end up running at less than their maximum brightness. You can of course choose to run a display at a higher than recommended brightness level, and the ambient lighting in a room will also determine what brightness setting is best. Our testing was performed indoors with a moderate amount of lighting, and the displays were adjusted according to directions. We also found that manually reducing the brightness level to something more reasonable (like 200-300 cd/m2) did not significantly affect the results on any of these displays, so consider the above charts as more of a maximum recommended brightness for each particular LCD.

Color Accuracy

Monaco Optix XR Pro


The 2707WFP's uncalibrated results were quite poor, but calibration helps it improve drastically. A few colors show a bit of a spike (dark blue and bright white), but the majority of the color results are very close to the "perfect" range and certainly acceptable for the vast majority of users. Both of the 30" displays are at the top of the charts, and it's likely that their S-IPS panels are simply better overall at providing accurate colors (post-calibration). Note also how all of the S-PVA have very similar curves, including a nearly identical spike on dark blue.

Uncalibrated Results Printing Results
Comments Locked

39 Comments

View All Comments

  • darklight0tr - Monday, April 9, 2007 - link

    On Page 4 it says that Screen Scaling doesn't work when using DVI, but that is incorrect. I have the 2707WFP, and the Screen Scaling menu isn't enabled in DVI UNTIL you switch the screen resolution to one that doesn't use the 16:10 aspect, such as 1600x1200.

    It confused me at first, but I guess it doesn't make sense to enable that menu if you are already running the monitor at 1920x1200.
  • JarredWalton - Tuesday, April 10, 2007 - link

    My screen scaling menu is definitely disabled with a DVI connection. I've tried several resolutions (1680x1050 and 1600x1200 for sure) and it never became adjustable. That said, the LCD is revision A00, and I know on the 2407WFP this was apparently something they addressed in a later revision of the firmware; perhaps they will do the same again. I felt this OSD was a step back relative to the latest 2407WFP firmware options, which is odd as it should be essentially the same menu. If they "fixed" something with Rev. A03 on the 24" model, why "unfix" it for A00 of the 27"? Oh well... I just report on what I have. :)
  • Amuro - Saturday, April 14, 2007 - link

    Did you use a Nvidia 8 series video card for the review? There are scaling issues with Forceware drivers later than 97.XX that forces adapter scaling at all times. If you try to change the scaling to something else in the Nvidia control panel, it will automatically go back to adapter scaling after you click Apply. The scaling menu on the LCD is disabled because the video card automatically streches everything to 19200 X 1200. I have a Rev A00 2707 WFP and I'm able to use monitor scaling before loading into Windows, and also ablo to do 1:1 scaling when using it with my PS3 at 10806P via DVI.
  • AnnonymousCoward - Friday, April 6, 2007 - link

    The article said "Furthermore, while nearly everyone will agree that running your LCD at its native resolution is the best solution, gaming on a 30" LCD at 2560x1600 requires some serious graphics horsepower." Well, there is a second native res that requires much less horsepower: 1280x800.

    I'm not sure how accurate your pixel pitch chart is, because if you go to tvcalculator.com, the results are different. Use that site to compare a 30", 16:10, 2560x1600 versus a 27", 16:10, 1920x1200 --> 10126/7030 is 1.44x pixel density on the 30". Using your pitch numbers (to convert distance per pixel to pixels per distance): 1/.250mm = 4pixels/mm, 1/.303mm = 3.3pixels/mm. 4/3.3 = 1.21x pixel density on the 30". I'd trust the physical size per resolution before I'd trust some published pixel pitch numbers.

    btw, if you're comparing CRTs on the site, don't forget to subtract an inch since LCDs go by the viewable inches.
  • JarredWalton - Friday, April 6, 2007 - link

    The table is composed of approximate values. The main point was that various sizes and resolutions will have a larger/smaller pixel pitch. So if you find a 19" 1280x1024 to be "good" and 17" to be "too small", you might like a pixel pitch similar to that of the 19". The HDTV values in particular could be way off, since I couldn't find any reasonable sources.
  • AnnonymousCoward - Friday, April 6, 2007 - link

    Yeah...and does pixel pitch mean the distance between the center point of each pixel? If so, and if the size of pixels vary per screen, then the pitch isn't the complete information since the gap between pixels probably also varies.

    The tvcalculator.com was useful for me before I bought a 30". I had a 21" CRT at my disposal, and it turns out that the pixel density is nearly identical at 1600x1200 to the 30" at 2560x1600.
  • TA152H - Thursday, April 5, 2007 - link

    Jarrod,

    Do you guys have any intentions of reviewing Eizo monitors sometime in the future? I'm not knocking the inferior stuff like Dell, Viewsonic, etc..., and I do understand that the masses buy this stuff in masses and the price makes them much more accessible. But, it wouldn't hurt to review the top quality stuff either, even if most people can't afford it. After all, you guys review $1000 processors, and high end graphics stuff. It's like a car magazine reviewing a Porsche. Most of it's readers can't afford it, but it still makes for interesting reading. We might end up with a Volkswagen (or Dell, or Viewsonic, etc...), but it does get readers. Since they sell so few monitors, I'm guessing they would love the exposure and you wouldn't have too hard of a time getting one. It can't hurt to ask. I have bought Nanao/Eizo until they stopped making CRTs, and they were much better than the other rubbish sold (and twice as expensive :P), and I think a review would be informative and open a few eyes (no pun intended).

    Also, are you guys done reviewing CRTs? I finally bought an LCD about four months ago because I kept reading how much better they were. Not only did I hate it, but I almost hit my cat with it (by accident) when I threw it out the window. I know they take some getting used to, but they have so many compromises compared to CRTs that I had to destroy it (NewEgg won't take them back). I'm not alone in this either, although I think a minority. Still, some reviews of the new Samsung monitors would be nice, and maybe the aforementioned Eizos are decent enough LCD monitors that they don't have to factor in flight attributes in the design, for when someone throws them out the window. It's a pity too, they weigh so little and take up so little desk space in comparison. I just can't stand the poor quality of the display. Why do they make them so bright anyway? Even turned down they can be really tough to look at.

    Also, if you do review CRTs, you might want to skip Viewsonic. They've managed to combine the worst of both worlds; their CRTs have dead pixels. I have no idea how this is possible, but they managed to do it and not only the one I bought. It's apparently a common problem. I have to give them credit for having the talent to create such a thing though, I didn't even know it was possible. Probably the shadow mask isn't transparent in that spot? I have no idea, really.
  • TA152H - Thursday, April 5, 2007 - link

    Hmmm, I just went to Samsung's web site and I don't even see their CRTs listed anymore. So maybe CRTs are finally dead, unless you want dead pixels. Oh brother, what a choice.
  • JarredWalton - Thursday, April 5, 2007 - link

    I think we are generally at the point now where CRTs truly are dead in terms of reviewing units. If I had a good late-model CRT available for comparison purposes, I would have included it in the test results already. Unfortunately, the best CRT that I had (note the use of past tense) was a 19" NEC (FE-991SB). I honestly don't even want to bother with CRTs anymore. LCDs certainly aren't perfect, but I will take the sharp image quality (no need to stretch/rotate/center your image like you have to do with CRTs) and the smaller size any day given a choice between CRT and LCD.

    I realize there are still CRT holdouts, and I do miss the higher refresh rates that CRTs offered, but hopefully we will see improvements in that area of LCDs in the not-too-distant future. If you already have a good CRT, you can probably continue to use that for a while longer. If on the other hand you are looking to go out and purchase a new display, I doubt many people would be interested in the current CRT offerings.
  • TA152H - Thursday, April 5, 2007 - link

    Actually, I did some research after I wrote that and Viewsonic, Phillips and CTX are still making them.

    Do you actually prefer the image on an LCD? I can't imagine anyone does, but I suppose some people do. It is probably your poor vision (no offense), because I could see the each pixel very clearly on my LCD and it's just not as lush a picture (incidentally, my vision sucks too, but only long distance. Short distance I see all too well). Also, the viewing angles aren't quite right. The top looks lighter than the bottom, for example, unless you move your head up. It's altogether an extremely flawed technology, and it hasn't really gotten much better in 20 years. In know the numbers look better, but the old ThinkPads I had at IBM didn't look that much worse than these monitors, and in 20 years they should have. I'm not saying if you put them side to side you couldn't tell the difference, you probably could, and they are a lot bigger now, but they aren't nearly as improved as I have seen spoken about. For that matter, neither are CRTs. My old Princeton Ultrasync had a fantastic picture, but it was only 12 inch.

    The most painful part of chucking the LCD was the footprint and weight. CRTs are awful in terms of creating heat too. In the summer, I want to chuck them out the window, but perversely their weight saves them from this form of destruction. (Even the illustrious dead pixel Viewsonic was discarded in a dump, although kicked and sledgehammered, rather than chucked out the window). The image quality is so hard to ignore though. For a TV, where size matters a lot and you generally watch from a distance, I think LCDs are great. But, being able to see each pixel and the terrible brightness, the poor viewing angles, the terrible ghosting, the weird bright green pixel that won't take no for an answer, and poor color saturation leave me cold. But, the handwriting is on the wall, although you'll probably have one company make CRTs for a long, long time, because even if 5% of the people can't stand LCDs, it's still a huge market. I think the number is higher than that too. Luckily, the Trinitron is dead. Another really badly flawed technology that people bought a lot of. How could people stand those lines or the asymmetric nature of the Trinitron? I never understood it. I'm equally baffled now by LCDs. Incidentally, the one I tossed was a ViewSonic VG2230wm. It was talked about well, but it was a huge disappointment compared to a CRT.

Log in

Don't have an account? Sign up now