General Performance and Encoding


Content Creation Performance

General Usage Performance

MPEG-4 Encoding Performance

General Performance

The values are so close together in Multimedia Content Creation and Business Winstone that you can basically conclude that the 5 tested boards are equivalent. There is no way to make a total variation from top to bottom of 0.4 points in Business Winstone or 0.5 points in Multimedia Content Creation significant. This variation represents only a 1.5% difference in the best and worst performance in this suite of 5 second generation Socket 754 boards. PCMark2004 is even more tightly clustered, with the spread from best to worst at only 0.9%.

The 2-pass Media Encoding benchmark also is of little help in differentiating the 5 boards in this roundup. As we have stated in earlier reviews, the on-board memory controller of the Athlon 64 tends to make any differences between boards much smaller than we have seen in the past with the memory controller on the chipset. This is particularly true in overall system performance and encoding benchmarks.

Standard Performance Test Configuration Standard Gaming Performance
Comments Locked

30 Comments

View All Comments

  • karlreading - Monday, August 30, 2004 - link

    i braught the chaintech vnf3-250 based on the review it recieved at AT and TBPH its a cracking motherboard, plus it easily gets my 2ghz a64-3200+ to 2.4 ghz and lets you run 1ghz HT if u running the cpu stock, something whic supposidly only the nf3 ultra let u do.all in all a very fast, very reliable, very overclockerbul motherboard which i have NMO regrets about buying :)
  • lem79 - Friday, August 6, 2004 - link

    I have the Epox 8KDA3+ here with an Athlon64 2800+, runs nice, except for one quirk, which Anandtech failed to mention here (they probably didn't even know)..

    Cool'n'Quiet only works on this board when _one_ DIMM slot is in use (that is, DIMM1). If there's RAM in DIMM2 and DIMM3 slots, Cool'n'Quiet gets disabled by the BIOS (July revision, earlier BIOS images leave it enabled, but Cool'n'Quiet activation causes system instability and lockups). Epox themselves told me that this was the case.

    I think the review needs updating..
  • operator - Sunday, June 6, 2004 - link

    I have the same question as #25. with a small addition.

    when will the msi k8n or the epox board be available in Canada?
  • Zebo - Wednesday, June 2, 2004 - link

    This is a very good review Wesley, thanks. I really like how you went into detail with memory and boards FSB capabilites for the clockers out here.:) Looks like the Chaintech is the board for me. Cheap and a real performer. It's really to bad nVidia failed to have a decent sound solution though.
  • Sk0t - Tuesday, June 1, 2004 - link

    Nice review.... BUT Im unable to understand why the Epox 8KDA3+ was awarded gold, and MSI K8n Neo Platinum only awarded silver ?

    Epox pros over MSI:
    6th pci-slot
    Slightly better overclocking

    MSI pros over Epox:
    Firewire
    3 working dimm sockets (at 400mhz)
    Slightly better layout (dimm-sockets)
    Supports Cool&Quiet*

    *Since the review seems to completly ignore cool&quiet (unless i missed it?) I will stick to my current rule of thumb, that only Asus & MSI fully supports this feature

    Did I miss some wonderfull feature on the Epox ? or was slightly better overclocking considered more important than features & layout ?
  • gmenfan - Tuesday, June 1, 2004 - link

    Does anyone know when the MSI K8N Neo will be available? Thanks.
  • mbf - Tuesday, June 1, 2004 - link

    Nice review! I just have one question; how can there be boards *without* ECC support, when the A64 has the memory controller on-die and it *inherently* supports unbuffered ECC memory? I'm especially thinking of the Epox and MSI boards, since they interest me the most (hardware firewall et al).

    Actually, I wrote to MSI (US) about this and was told that indeed ECC is supported and the "non-ECC" statement on the product spec page was erroneous. The page was immediately updated (http://www.msicomputer.com/product/p_spec.asp?mode... However, only the US site has been updated, and neither the manual (PDF) nor the BIOS available from the MSI Taiwan site state ECC support. Neither do the manual or BIOS for the Epox board.

    As ECC support is pretty important to me having had some bitter experiences with regular memory, I was wondering if some kind person at Anandtech might be persuaded to throw in a stick of unbuffered ECC memory into either the K8N Neo or the Epox 8KDA3 and let me know if the memory is detected as such? I'd really appreciate the effort!

    I know the ASUS K8N-E Deluxe (http://www.asus.com.tw/products/mb/socket754/k8n-e... states ECC support, but it's anyone's guess when that board will be out, since they cannot even make their mind up if the board is to be shown on their home page or not (right now it is, tomorrow it may not).
  • l3ored - Tuesday, June 1, 2004 - link

    price is mentioned as a component in electing the epox as the gold winner, so whats the current street price?
  • SilverRyu - Monday, May 31, 2004 - link

    Do you think shuttle will make a 250Gb or K8T800Pro XPC?
  • cnq - Monday, May 31, 2004 - link

    Wesley,

    Nice writeup...
    A question about overclocking: you tested at 1:1 ratios, meaning you didn't really find the bounds of the FSB/HTT so much as you found the bounds of the PC4400 RAM that you used. If you had dropped the RAM ratio, do you have any indication which boards could have topped 300 MHz? I am of course thinking of your great AK89 Max review from a few weeks back, where you made waves by showing FSB/HTT speeds of 347 MHz. Will you have time to do similar tests on these new boards? (Or, for that matter, can I ask why you didn't do similar tests on these new boards? Is it merely because ClockGen hasn't yet been ported to NF250?)

    I'd also like to second the suggestion made by posting #1 (he mentions aceshardware.com. techreport.com has also chimed in with recent articles on the subject. Not surprisingly, their conclusion is to just avoid cheap Realtek products if you want good CPU utilization. And sudhian.com found great ethernet performance with low CPU overhead from the NF250-GB chip's embedded controller.)

Log in

Don't have an account? Sign up now