Cooler Master Elite 120 Advanced Case Review: Little in Almost Every Way
by Dustin Sklavos on July 26, 2012 3:01 AM EST- Posted in
- Mini ITX
- Cases/Cooling/PSUs
- Cooler Master
Testing Methodology
For testing Mini-ITX cases, we use the following standardized testbed in stock and overclocked configurations to get a feel for how well the case handles heat and noise. Again, note that while the GD07 can technically fit a full-size ATX motherboard, it's not tall enough to allow for our testbed's tower cooler. Because of the discrepancies that would make for in testing, plus the fact that media center cases are often mini-ITX designs, we have chosen to use our mini-ITX testbed rather than going with a specialized (e.g. not something you can compare directly to our other cases) ATX build.
| Mini-ITX Test Configuration | |
| CPU |
Intel Core i3-2120 (65W TDP) |
| Motherboard | Zotac Z68ITX-A-E |
| Graphics Card |
Intel HD 2000 IGP Zotac GeForce GTS 450 Eco (dedicated) ASUS GeForce GTX 560 Ti DCII TOP (dedicated extra) |
| Memory | 2x2GB Crucial Ballistix Smart Tracer DDR3-1600 |
| Drives |
Kingston SSDNow V+ 100 64GB SSD Samsung 5.25" BD-ROM/DVDRW Drive |
| Accessories | Corsair Link |
| CPU Cooler | SilverStone NT07-1156 with Cooler Master ThermalFusion 400 |
| Power Supply | SilverStone SFX ST45F 450W |
Each case is tested with just the Core i3's integrated graphics as well as with a discrete graphics card. The system is powered on and left idle for fifteen minutes, the thermal and acoustic results recorded, and then stressed by running four threads in Prime95 (in-place large FFTs) on the CPU, and OC Scanner (maximum load) is run when the dedicated GPU is installed. At the end of fiteen minutes, thermal and acoustic results are recorded. If the enclosure has a fan controller, these tests are repeated for each setting. Ambient temperature is also measured after the fifteen idle minutes but before the stress test and used to calculate the final reported results.
We try to maintain an ambient testing temperature of between 22C and 24C. Non-thermal test results aren't going to be directly comparable to the finest decimal point, but should be roughly comparable and give a broader idea of how the enclosure performs.
Thank You!
Before moving on, we'd like to thank the following vendors for providing us with the hardware used in our testbed.
- Thank you to Puget Systems for providing us with the Intel Core i3-2120.
- Thank you to Zotac for providing us with the Z68ITX-A-E motherboard and GeForce GTS 450 Eco.
- Thank you to Crucial for providing us with the Ballistix Smart Tracer memory.
- Thank you to Corsair for providing us with the Corsair Link kit.
- Thank you to Kingston for providing us with the SSDNow V+ 100 SSD.
- Thank you to CyberPower for providing us with the Samsung BD-ROM/DVD+/-RW drive.
- And thank you to SilverStone for providing us with the power supply and NT07-1156 heatsink/fan combo.
Facebook
Twitter
RSS
65 Comments
View All Comments
philipma1957 - Thursday, July 26, 2012 - link
The case looks decent in a htpc rack.problem is it is noisy.
I use a sapphire hd 6670 ultimate video card. it is passive. = silent
I use a seasonic 400 watt fanless psu = silent
i use an asrock itx board = not cheap
i use an intel i5 2500t cpu = low power runs cool
i use an ssd = silent
i use a 500gb 2.5 inch 5400 rpm hitachi = very quiet
i use a samsung blu ray drive.
this would have been a nice htpc machine in a rack ,but the stock fans are noisy.
I need to play with it some more.
the small 80 mm fan on one side is the problem very noisy.
also using a low cpu cooler heatsink is a must.
the cpu cooler blows right into the psu.
I think if i had a psu with a fan and let it pull hot air out of the machine
i could keep the machine cooler. maybe then i can lower the fan speed on the small fan.
as for ugly the cooler master label is flat out not needed and is truly the worst part of its looks.
lwatcdr - Monday, July 30, 2012 - link
Why an i-5 and an external graphics card for an HTPC? A Celeron or I3 T would be more than good enough for for an HTPC with a GPU. Or you could use an Ivy-Bridge i5 with the onboard GPU for lower cost and thermals. The only good reason to have an i5 and a GPU would be gaming. Also you might want to consider dumping the HD and using a NAS for media storage. That can be in another room and you can put as many big cheap drives as you want on one. Even something like PoGo plug will work for serving media.flparula - Thursday, July 26, 2012 - link
I've built 2 mini-itx systems. I used one of the older Lian cases. The case uses a full sized ATX power supply; but I only have used modular cable-ling. The last build used a all-in-one water cooler. Is there enough room to put a water cooler, e.g. Corsar H60 or Antec 620. Water coolers also fix a problem that low-profile fans run into with all of the cables (usual power supplies have too long of cables) a fan can hit the cable and stop cooling. No such problem with the water cooler.ggathagan - Thursday, July 26, 2012 - link
Water cooling in this case would require some cutting and would almost certainly require you to mount both the fan and the radiator on top of the case.It would be possible to snake the coolant lines between the PSU and the GPU, but the length of the coolant lines might be an issue.
All in all, you'd be better served with a different case.
cjs150 - Friday, July 27, 2012 - link
Whilst I agree a different case would be better I think this case is capable of supporting water cooling, just a little imagination is needed. Remove the drive cage and use a slim line optical drive with room for one or 2 2.5 drives beneath it (or drop the optical drive). Take a 120mm radiator (140 may fit) and turn it 90 degrees so barbs are on the side. Use the new swiftech apogee drive and you have a watercooling system that can cope with the CPU and (probably) a low heat GPU. You can also use the water cooling hole at the back as a fill port so not entirely wasted.Personally I think it is all a bit too cramped for that but it is certainly plausible
KasiorMC - Thursday, July 26, 2012 - link
on itxgamer.com forums someone posted one of these: http://www.amazon.co.uk/accommodate-supply-Optical...is there any chance of you testing it in near future?
it's roughly the same size, same price... only with different (better?) layout
adboelens - Thursday, July 26, 2012 - link
I have owned two mini ITX cases that had SFX power supplies. Both I found too noisy, while an entry level 300 ATX one can be almost completely quiet. I now have a Lian Li one and very happy with performance and noise level.Metaluna - Thursday, July 26, 2012 - link
Yes it's a problem of trying to cram too much power dissipation into too small a space. There's only so much you can do with forced airflow before the fans get too noisy. Using standard modular components makes things worse as they aren't going to be tailored to match the case's layout and airflow (the author touched on this a bit talking about the chore of trying to cram ridiculously long PSU cables designed for a tower case into a mini-ITX case.)Guspaz - Thursday, July 26, 2012 - link
Well, when you try to remove all the heat dissipated in a computer using 300-400 watts with a single 92mm fan (what the Shuttle SZ77R5 uses, because that's as big as they could possibly fit on the rear), you're going to have to spin that fan pretty fast to exhaust all that heat. And when you spin a fan at 3000+ RPM, it's going to get loud no matter how fancy your fan gets.I think they could have designed the SZ77R5 (and other similar SFF cases) a bit differently, though. For clarification, in the SZ77R5, the CPU's cooler is just a plate attached to heatpipes that connect to a heatsink that mounts to the rear of the case, and a single 92mm fan blows air through that, acting as both a CPU and case fan. If, instead, a 92mm fan was placed on the top of the case, a 120mm or even larger fan could be used, which would allow the same amount of air to be moved while spinning at a much lower speed.
PyroHoltz - Thursday, July 26, 2012 - link
Get rid of the massive logo on the front. I'm not in the market to advertise for the companies I buy from.If people want the Cooler Master logo, give them a sticker.