Assembling the Lian Li PC-A55

Credit where credit is due, Lian Li's PC-A55 came together very smoothly. Usually smaller enclosure designs are difficult to assemble and somewhat involved, but the PC-A55 is very clean and logical and I seldom had to consult the instruction manual to figure out how to get everything to fit inside it.

Starting with the motherboard, while clearance around it is minimal, I'm always happy to see the stand-offs come preinstalled. It's a simple, thoughtful convenience that saves time in the long run. While ordinarily I attach the modular cables to the board first and then plug everything into the power supply at the last step, that's not possible in the PC-A55 due to the reduced clearance between the power supply mount and the drive cage. As a result, I actually connected the necessary cables and installed the power supply almost immediately after installing the motherboard.

Note that we're using a Micro-ATX motherboard as usual, but the only real difference you'd see with a full-size ATX board is that it would be "taller" in the pictures below. Our test board is just as deep as a standard ATX board, but it doesn't have as many expansion slots.

Installing the power supply involves removing a bracket from the bottom front of the enclosure. The power cable is already routed through this bracket and is easy to connect to the power supply, but when we put the PSU and bracket back inside the PC-A55, we discover what I would consider a potentially serious design flaw. The PSU can only be oriented one of two ways: either the bottom-mounted intake fan faces the interior of the case, disrupting the intended airflow, or it faces the inside of the front panel, in which case it's blocked off entirely.

At this point I also learned that the drives should probably be installed first. I had to remove the RAM from the motherboard to fit the 3.5" drive into the bay, though the 5.25" drive was able to slide in from the front of the PC-A55 relatively easily. Note that it's entirely possible to butt the 5.25" drive up against the edge of the motherboard, too. Unusually deep optical drives (like LG's combination HD-DVD/Blu-ray drive) simply won't fit without sticking out of the front of the case. 2.5" drives still use Lian Li's traditional bottom-mounted rubber grommets to slide into the two mounts.

Getting the video card in was easy enough, though, and wiring the PC-A55 was surprisingly simple. Our test SSD does press up against the bottom of the PC-A55, making it a little more difficult to get the data and power cables connected, but it's a minor quibble in the scheme of things. What you have to remember is that because the PC-A55 lacks any space behind the motherboard tray (and is small in general), there's really nowhere to put the cables except to cram them into the space beneath the drive cage.

Once I crammed everything into Lian Li's PC-A55, I immediately realized just how poorly the thermal design might actually perform. Here's the essential problem: if you install a full-height video card, about 75% of the bottom-mounted intake fan is going to be blocked by it, substantially reducing any air that comes in through the case's single intake, leaving the top-mounted exhaust fan to pick up the slack. This also means that multi-GPU is going to be basically out of the question, since the gap between the video cards is going to be basically dead, having nowhere to actually take in air from.

Things get worse. The rubber pegs the case stands on are only about 15mm high, meaning that in the best-case scenario, the intake vent of the PC-A55 is only going to be about 15mm off of the ground. The fan filter shaves another 3mm off of that. This is why every case I've reviewed thus far that had a bottom fan mount left that mount optional and didn't rely on it, excepting the Silverstone cases which all stood at least a full inch off of the ground, allowing for a healthy amount of ventilation and clearance even on carpet. Bottom line: the PC-A55 more or less can't be used on any carpet of any kind, as the bottom intake will be suffocated by it.

In and Around the Lian Li PC-A55 Testing Methodology
POST A COMMENT

63 Comments

View All Comments

  • i077 - Saturday, June 16, 2012 - link

    What about just simply turn the top exhaust fan around and make it an intake? In that way the CPU area will get some fresh air that it desperately need. The CPU fan can be position to the other side of the heat sink and double as an exhaust fan, or just add an 140mm to the back.

    The power supply positioning is a massive failure though. It has no dedicated intake or out take, and ends up being a pure heat generator tuck away at the bottom corner. If they just poke some hole in the front panel and at the bottom and separate the PSU into its own thermal zone this case could have been something.

    Hopefully they do a revision soon, the case does look sharp and uses space wisely.
    Reply
  • Pazz - Saturday, June 16, 2012 - link

    Shame about the poor thermals but I suppose to be expected when they adopt a vertical system without rotating the mainboard.

    I do like the small form factor full-ATX idea though since a lot of standard ATX cases are approaching gigantic. The average enthusiast doesn't require 7x 5.25" or 6x 3.5" bays. Particularly now that SSD's are mainstream and optical drives superflous.

    PC-A05NB FTW (note I did not type A05FNB)
    Reply
  • mbf - Saturday, June 16, 2012 - link

    ...might just possibly help with cooling in this case. Reply
  • SimKill - Saturday, June 16, 2012 - link

    I'm a regular lurker here, but I think in this specific review you've made an unnaturally high number of mentions of the complete model number instead of using words like "it", "it's" etc. Reply
  • Dustin Sklavos - Sunday, June 17, 2012 - link

    I think you're just seeing things. Why would I do something like that? Reply
  • erwendigo - Monday, June 18, 2012 - link

    Because you have a very bad sense of humor (cheapest). And "we" (more than one) can see it. Reply
  • Dustin Sklavos - Monday, June 18, 2012 - link

    Hey, I don't go to your place of business and insult you. Reply
  • AssBall - Tuesday, June 19, 2012 - link

    Lian Li might disagree with that statement, relative to how the article was titled.

    But you can't stay mad at what was essentially a completely honest and well done review. If your product is ass, its ass.
    Reply
  • mcbowler - Saturday, June 16, 2012 - link

    LIAN LI,

    Please hire me to design a case.
    Reply
  • etrigan420 - Saturday, June 16, 2012 - link

    Really?

    I expected a little more from Anandtech.
    Reply

Log in

Don't have an account? Sign up now