ECS H55H-I Review: Mini-ITX at a Sensible Price
by Rajinder Gill on May 6, 2010 6:59 AM EST- Posted in
- Motherboards
The H55H-I follows Intel’s standard H55/H57 mini-ITX layout. CPU socket placement is very close to the PEG slot and the DIMM slots to the right, leaving most tower type coolers out of the equation if using tall DIMMs.
The SATA ports and front panel connecters are placed at the top left of the board along with the CMOS jumper. Given the overclocking options provided and the fact that ECS’ BIOS does not have any kind of safe-boot feature, a rear panel button would have been a better choice.
Power delivery is taken care of by a three phase circuit for VCC, while VTT and VAXG get one phase supplies repectively. We’d guess that all FETs used can pump out around 30 amps each, so not a lot of room for overclocking four core processors.
This is probably the most barren backside we’ve seen on a mini-ITX board to date. There's more than enough room to use coolers with backplates, although we can’t see many people wanting to do that.
Most of what you need is provided on the backplate, the only exception being PS/2 for those of you with older keyboards and mice.
Facebook
Twitter
RSS
67 Comments
View All Comments
nubie - Thursday, May 6, 2010 - link
The industrial market uses (used?) ISA cards.Try Soyo, Supermicro, and Jetway for industry boards.
Powerlurker - Thursday, May 6, 2010 - link
http://adek.com/ATX-motherboards.htmlI needed to spec one a couple years ago for a piece of lab equipment (I too work in a chemistry lab). It looks like this is the website for the motherboard manufacturer. http://www.commell.com.tw/Product/SBC/P4BWA.HTM
nubie - Thursday, May 6, 2010 - link
How could I forget Commell,Thanks :)
kmmatney - Friday, May 7, 2010 - link
I've purchased several of the ADEK boards to support some old ISA motion controllers we have. The motherboards are around $300, while a new motion controller (these are quite advanced) would have cost about $4000. They work great!Earthmonger - Thursday, May 6, 2010 - link
Really, it is. I could previously count the number of socket 1156 ITX boards on one hand. This ECS is a welcome addition."However, if you're thinking of overclocking with this board, we'd say that ECS is a couple of BIOSes away from a glowing recommendation"
What ITX board would you recommend for overclocking, then? 'Cause I'm always thinking about it. Where's that EVGA ITX powerhouse at? lol
Rajinder Gill - Thursday, May 6, 2010 - link
Hi,Unfortuantely, all mini-ITX boards are limited in one way or another. Either by voltage options (insufficent current handling capacity), and/or the need of some BIOS polish as in the case of ECS.. I'm hoping we see someone put a 180amp capable VRM on one of these baords soon...lol
regards
Raja
MadMan007 - Thursday, May 6, 2010 - link
Yes that would be nice and I don't buy the 'limited space' argument either. There are plenty of good overclocking microATX boards that don't use a ton of space for VRMs. I was hoping DFI would push things in this area but not yet...maybe since they are supposedly focusing on smaller form factors going forward they will.JonnyDough - Thursday, May 6, 2010 - link
Well, not quite legacy free. Isn't that a VGA connector? :)DanNeely - Thursday, May 6, 2010 - link
Mostly it matters for people doing low level OS development because PS2 requires much less software support than USB. If you're not hacking the linux kernel/porting it to new hardware it, along with RS232 are only really needed for high price hardware interfaces.lwatcdr - Thursday, May 6, 2010 - link
PS/2 ports and legacy serial and parallel ports can be a very important.Remember this is a Mini-ITX board. A good number of these end up in industrial settings.
Things like CNC machines, and lab equipment use good old serial and parallel ports to interface. They may also have a custom front panel that uses a PS/2 interface.
Even floppy's are still used on some systems like that and some of the software for them even runs under dos!
For a nettop or desktop you are correct. They less than useful but there is a large market segment that will need them for a long time. BTW USB to serial converters tend to be crap.