Efficiency and PFC




Efficiency was consistent across the four tested units, with differences of only 1%-2% at the various loads. Only the 350W model failed to reach 86% efficiency, topping out at 85% instead. As we discussed recently, small differences in efficiency aren't a major concern. All of the tested models also stay above 80% efficiency as long as the load is at least ~10%, so these power supplies would be a great fit for entry-level to midrange systems.


The power factor correction only reaches .98 with 230VAC - acceptable but it could be better. Lower input voltages as always have better PFC.

DC Output Stability and Quality Temperatures, Fan Speed, and Acoustics
Comments Locked

36 Comments

View All Comments

  • CEO Ballmer - Wednesday, November 19, 2008 - link

    I like this, I'll have to try a few hundred!

    http://fakesteveballmer.blogspot.com">http://fakesteveballmer.blogspot.com
  • JonnyDough - Thursday, November 20, 2008 - link

    Can you ban this user's IP please? He keeps spamming over at Tom's Hardware also.
  • strikeback03 - Friday, November 21, 2008 - link

    If they want to keep spamming, they can just get a new IP.
  • phreax9802 - Wednesday, November 19, 2008 - link

    Only one 6-pin PEG connector? Come on..this is 2008! My old Enermax FMA II 460W has two of them..
  • fic2 - Wednesday, November 19, 2008 - link

    You measured that the secondary heat sink temp reached 80 degrees. How hard would it be for a user to replace the secondary with a larger heat sink? How hard would it be to find an appropriate heat sink for this? I looked on the internals pictures but couldn't find anything that I thought looked like a heat sink except maybe what looked like separator walls.
  • ggathagan - Wednesday, November 19, 2008 - link

    Regardless of how hard or easy it is, replacing the heatsink would void the warranty.
    It also misses the point: The manufacturer should be supplying the appropriate heatsink in a properly designed PSU. If they don't, why should I buy it?
  • sam187 - Wednesday, November 19, 2008 - link

    Hallo Christoph,

    danke fuer deine ausfuehrlichen Reviews auch mal aus der Heimat ;-)

    First, it would be nice to see a comparison in the 300-500W range. Next to that, please take a look at things like the picoPSU. Are they that much more efficient than normal psus and do they meet the demands for current htpc platforms (g45/780g/nv9300 with a small cpu)?

    Sascha
    Hamburg, Germany
  • haplo602 - Wednesday, November 19, 2008 - link

    Thanks for the review. I'd like to see some more 350W and 450W PSUs.
  • xaris106 - Wednesday, November 19, 2008 - link

    I also think its great to review "low" wattage models. It's the biggest portion of the market, as you say in your articles, an I aggree. So thanks for reviewing this and i also hope you continue with this range of wattages. We all know that buying a high end high power model from a good brand, we will propably get a quality psu. But not so in the 300-500W range.

    What I would like to see is:
    1) Step load tests: I would like to see how each psu handles load changes (eg a sudden 1A change). The voltage overshoots, settling times can give a lot more information about the quality of a psu.
    In other words..transient response tests.

    2)A review, maybe as reference of an as cheap as it gets no name psu, to see what we get more with our money spent on brand name psu.

    Thanks.
  • Boushh - Wednesday, November 19, 2008 - link

    What I would like to see is good quality sub 400 Watt modulair power supply's. These are (almost ?) impossible to find.

    It's a miss calculation from the manufactures that people will not pay more for these units. Many people who employ sub 400 watt units do this because they don't need more, and because it will have to fit into a smaller case. Then all those cables are just in the way, because they will not be used.

    Further more (as suggested in to article) using high quality design and materials will give better power supply's. Sure they will cost more, but I'll gladly pay that if some manufacturer would build them.

    And I don't think I'm alone in this. So please manufactures, start listning to your customers !!!!!

Log in

Don't have an account? Sign up now