Product Comparison: DC Outputs







We have to say we are quite impressed by all of the units for having such a great and stable power delivery throughout testing. As usual, all of the units start above 12.00V, but even when delivering 500W of power the 12V rails are over 12.00V on more than half of the units. At full load, some of the power supplies are starting to drop off rapidly, though all remain in spec. The OCZ ProXStream shows its full potential by delivering a stable output of 11.92V at 100% load, which is just a little less than the optimal amount.







With the lower voltage rail of 5V, we see similar results as the 12V rail. The units have no real problems distributing up to 100% of load. Coming to these high loads for 1000W PSUs is getting more and more difficult for the power supplies but as we can see all of the units are still inside specifications.







With the 3.3 V rail we see three power supplies coming close to the lower end of the specified range. Remember, the lowest "allowable" value is 3.14V, and 3.16 or 3.17 are quite close to that amount. As the results show, the OCZ is again on top of the others and even under high load delivers a stable 3.24V - quite impressive.

Product Comparison: Cable Lengths Product Comparison: Voltage Ripple/Noise
Comments Locked

29 Comments

View All Comments

  • kuraegomon - Wednesday, December 12, 2007 - link

    Except that you don't want to run your power supply at 80-100% of its capacity. You probably want to run at 50-70% of capacity when you do your build for several reasons:

    - expandabiliity (though hopefully future components will be MORE efficient, not less - can't count on it though, especially with graphics cards)
    - component life. Any power supply will last longer if it's being run at a lower percentage of its rated capacity. It'll also run cooler, which means:
    - less degradation. Over time power supplies lose capacity. A five year-old power supply can't meet the same current/wattage specs that it could when it was new. This process is accelerated by thermal conditions. The hotter the PS runs, the more quickly its peak capacity will degrade.

    So, in my case, I have 2 x 8800 GTX's (overclocked), a Q6600 G0 (overclocked), 4 x 10K Raptors (RAID 0), 2 x 7200 Seagate 7200.10 (RAID 1), plus 4 GB of DDR2, and a 3Ware 9650SE 8-port hardware RAID card. My system draws over 500 Watts at IDLE, Over 650 Watts at heavy load, and I'm only running a 25% overclock on my CPU, and no overclock on my memory. How much expansion room would even a quality 650-750 W power supply give me, and how reliable will it be under similar loads in 5 years?

    That's why I have a Thermaltake Toughpower 1200. Efficiency runs 80-87%, and I'm running it at no more than 60 % capacity. Good recipe for maximizing the life of the expensive power supply, and even more so the even more expensive components it powers. My advice? Figure out the total load draw of the following components, then make sure that number is less than 70% of the max capacity of whatever quality power supply you purchase:

    - Graphics card
    - Hard drives - DON'T forget about access draw and spin-up. HD's draw significantly more power on spinup. Multiplied when you're running RAID arrays, even if you configure staggered spinup, you still will have multiple drives accessing at once. Relatively small but it adds up
    - CPU, especially quad-cores
    - Memory, especially more than 2 GB. Many people overlook this factor when calculating potential power draw, but 4 GB of fast DDR2 will pull significant wattage (more than 1 or 2 hard drives, in most cases). Luckily DDR3 consumes less power. Hopefully graphics cards stick to this trend as well!

    The short version: there absolutely are people who need and should buy 1000+ Watt PS's, who don't run 16 drives, 4 video cards, etc. Most people don't, but equally, many people underestimate the amount (and quality!) of PS they need.
  • kuraegomon - Wednesday, December 12, 2007 - link

    Correction: over 400 W at idle. Though closer to 500 than 400
  • Christoph Katzer - Wednesday, December 12, 2007 - link

    Coming from next year on.
  • regster - Tuesday, December 11, 2007 - link

    These test results for Product Comparison: Voltage Ripple/Noise are flawed in as the setting for the different pictures are set to different voltages from different manufactures. This implies that one is nosier than another when in fact they are not.
    People are going to be making purchasing decisions on these results and we can only think you are totally incompetent or that you are being paid off by some manufactures to make there product look better.
  • Christoph Katzer - Wednesday, December 12, 2007 - link

    That's why I write the results below in the text. There aren't any misunderstandings since a user who can't read these graphs will not make assumptions and a buying decision with it.
  • madgonad - Tuesday, December 11, 2007 - link

    I still would like to know what kind of results inexpensive power supplies turn in. I know everyone likes to dream about dual-quadcores and 4x Crossfire, but that is a market measured in the low thousands. Choosing a power supply for home builders is often a place where some corners are cut. It would be nice to know which choices don't really cut those corners.
  • sprockkets - Tuesday, December 11, 2007 - link

    So much for hoping you would test any FSP units this time around.
  • Christoph Katzer - Wednesday, December 12, 2007 - link

    Send me one I test it. I know FSP for quite some time already but unfortunately they haven't been able to send me some pieces in until now...
  • AMDJunkie - Tuesday, December 11, 2007 - link

    While testing and posting a review of 8 seperate 1KW power supply units is an admirable job, reading it felt of the first draft quality. There is nothing glaringly wrong, but it seems that some points are mentioned to never be addressed later on (you say the Ultra X3 is the older power supply of the lineup [and you might want to qualify that statement with dates], adding it in to see whether newer power supplies perform better, or are just new. Where is your conclusion on this point?) or simply having too many charts and not enough analyses - there are only two paragraphs that sum up 8 units in the ripple test?

    Even if they are very similar performing and that no one could go wrong with either unit, do take the time to go out of your way to point out what minor differences there are and give your opinion as well as your facts. The conclusion is conspicuously lacking in this regard. Otherwise, a very informative review. If only I hadn't already purchased an 800W unit!

Log in

Don't have an account? Sign up now