nForce4 SLI Roundup: Painful and Rewarding
by Wesley Fink on February 28, 2005 7:00 AM EST- Posted in
- Motherboards
DFI LANParty nF4 SLI-DR: Overclocking and Stress Testing
Overclocking
| Front Side Bus Overclocking Testbed | |
| DFI LANParty nF4 SLI-DR | |
| Processor: | Athlon 64 4000+ (2.4GHz, 1MB Cache) |
| CPU Voltage: | 1.55V (default 1.50V) |
| Cooling: | Thermaltake Silent Boost K8 Heat sink/Fan |
| Power Supply: | OCZ Power Stream 520W |
| Memory: | OOCZ PC3200 EL Platinum Rev. 2 (Samsung TCCD Memory Chips) |
| Hard Drive: | Seagate 120GB 7200RPM SATA 8MB Cache |
| Maximum OC: (Standard Ratio) |
238x12 (Auto HT, 2-3-2-7, 1T, 2.9V) 2856MHz (+19%) |
| Maximum FSB: (Lower Ratio) |
318x9 (2862MHz) (Auto HT, 2.5-4-3-7, 2.9V) (1:1 Memory, 1T, 2 DIMMs in DC mode) (+59% Bus Overclock) |
The DFI nForce4 boards set new records with this CPU and memory - reaching the highest overclocks at stock speed and at a lower mulitiplier that we have ever tested with this combination. We reached a very satisfying 318 (DDR636) at 1T, at the rather aggressive memory timings of 2.5-4-3-7 with our standard OCZ PC3200 Platinum Rev.2, which is based on Samsung TCCD chips.
As we detailed in our DFI review, DDR636 translated into a Quake 3 ran at 642FPS and SiSoft Sandra 2004 standard memory bandwidth was 8,300 MB/s. The Sandra unbuffered memory bandwidth was at 4000 MB/s. All these results are new performance records in our memory testing. The very wide range of memory voltages to 4.0V is particularly useful in reaching the highest possible overclocks, along with a very complete set of memory tweaking options in the BIOS. There is still a huge reserve in the available memory voltage range as we only needed 2.9V to reach these performance levels. Those with exotic cooling will appreciate that the CPU voltage and memory voltage settings on the DFI will give them what they need to squeeze every bit of performance from their CPU and memory.
Memory Stress Tests
Our memory stress test measures the ability of the DFI to operate at its officially supported memory frequency (400MHz DDR), at the lowest memory timings that OCZ PC3200 Platinum Rev. 2 modules will support. All DIMMs used for stress testing were 512MB double-sided (or double-bank) memory. To make sure memory performed properly in Dual-Channel mode, memory was only tested using either one dual-channel (2 DIMMs) or 2 dual-channels (4 DIMMs).| Stable DDR400 Timings - One Dual-Channel (2/4 DIMMs populated) |
|
| Clock Speed: | 200MHz |
| CAS Latency: | 2.0 |
| RAS to CAS Delay: | 2T |
| RAS Precharge: | 7T |
| Precharge Delay: | 2T |
| Command Rate: | 1T |
Using two DIMMs in Dual-Channel 128-bit mode, the memory performed in all benchmarks at the fastest 2-2-2-7 timings at default 2.6V voltage.
Tests with 4 DS DIMMs on an AMD Athlon 64 system are more demanding, since AMD specifies DDR333 for this combination. However, most AMD Athlon 64 motherboards combined with recent AMD processors (the memory controller is on the AMD CPU) have been able to handle 4 DIMMs at DDR400.
| Stable DDR400 Timings - 4 DIMMs (4/4 DIMMs populated) |
|
| Clock Speed: | 200MHz |
| CAS Latency: | 2.0 |
| RAS to CAS Delay: | 2T |
| RAS Precharge: | 7T |
| Precharge Delay: | 2T |
| Command Rate: | 2T |
Tests with all four DIMM slots populated on the DFI nForce4 boards required a 2T Command Rate with 4 DS DIMMs in two dual channels. This is the pattern seen on other top-performing Socket 939 boards, but we hoped higher voltage might allow us to eek out 4 DS DIMM 1T performance. However, additional voltage did not help and DDR400 with 4 DS DIMMs still required a 2T Command Rate on the DFI nForce4 boards.
Facebook
Twitter
RSS
108 Comments
View All Comments
eva2000 - Monday, February 28, 2005 - link
whoops no mention of psu was used in system config listing but didn't read till page 20 of the review it mentions OCZ 520W PS psu hehSlaimus - Monday, February 28, 2005 - link
They used a OCZ 520W.neologan - Monday, February 28, 2005 - link
I think the test results for 3dmark2003 single and SLI are the wrong way around?http://www.anandtech.com/mb/showdoc.aspx?i=2358&am...
F4810 - Monday, February 28, 2005 - link
Why did they show no benchmarks with the mobo's overclocked? It doesnt make sense to say these boards are better becuase you can clock the memory higher if the overall CPU clock is roughly the same. The reason they dont show you is that due to the onchip memory controller on the AMD chips, the high memory frequency doesnt make much of a difference at all in real world terms. As long as you can clock the CPU high that is all that really matters. Also they dont take into account cost as some boards cost 50% more that the others.dornick - Monday, February 28, 2005 - link
I was considering jumping on the SLI bandwagon until I had some sense knocked into me.I'd like to see a comparison of the Ultra chipset MBs, including the Chaintech, Epox, etc... since that's where I think the nForce 4 market will go.
eva2000 - Monday, February 28, 2005 - link
missing one vital piece of info, what PSU you used heheSpacecomber - Monday, February 28, 2005 - link
Thanks for doing the indepth analysis of this new chipset and how it is being implemented by some major motherboard manufacturers.There was one detail that I was hoping to see some reference to. I understand, from a friend, who has the MSI SLI motherboard, that the Creative Live sound chip only works if your power supply has a -5 volt connector on it. It looks to me like the OCZ power supply that you used has this, but many of the new power supplies, such as the Enermax v2.0 power supplies, no longer have a -5 volt connection. He was using a Enermax 535 watt Whisper II (SLI ready) when he ran into this issue. This kind of compatability problem slipping through QA seems like another indication that the everyone was in a big hurry to get these motherboards to market, maybe before they were thoroughly tested.
Space
Regs - Monday, February 28, 2005 - link
I liked the subtle hints Wes.In your final words you stated, "If you want the best performance possible then the answer would likely be yes". Then how would this apply for users getting two 6600GTs?
xsilver - Monday, February 28, 2005 - link
great articleminor gripe -- the overclocking "graphs" are useless -- what would be better is the resulting fps of overclocking to show people if its worth it to get that extra xxx fps
arfan - Monday, February 28, 2005 - link
now i am waiting ultra mobo benchmark. What about the price of all this mobo ? i fell disappointed with msi doesn't have PCI 1x. (Sorry my english language is very bad)