While display interface standards are slow to move, at the same time their movement is inexorable: monitor resolutions continue to increase, as do refresh rates and color depths, requiring more and more bandwidth to carry signals for the next generation of monitors. Keeping pace with the demand for bandwidth, the DisplayPort standard, the cornerstone of PC display standards, has now been through several revisions since it was first launched over a decade ago. And now this morning the standard is taking its biggest leap yet with the release of the DisplayPort 2.0 specification. Set to offer nearly triple the available bandwidth of DisplayPort 1.4, the new revision of DisplayPort is almost moving a number of previously optional features into the core standard, creating what’s in many ways a new baseline for the interface.

The big news here, of course, is raw bandwidth. The current versions of DisplayPort – 1.3 & 1.4 –  offer up to 32.4 Gbps of bandwidth – or 25.9 Gbps after overhead – which is enough for a standard 16.7 million color (24-bit) 4K monitor at up to 120Hz, or up to 98Hz for 1 billion+ color (30-bit) monitors. This is a lot of bandwidth, but it still isn’t enough for the coming generation of monitors, including the likes of Apple’s new 6K Pro Display XDR monitor, and of course, 8K monitors. As a result, the need for more display interface bandwidth continues to grow, with these next-generation monitors set to be the tipping point. And all of this is something that the rival HDMI Forum has already prepared for with their own HDMI 2.1 standard.

DisplayPort Signaling Standards
Standard Raw Bandwidth
(4 Lanes)
Effective Bandwidth
(4 Lanes)
Target Monitor Resolutions
DP 1.0/1.1 (HBR1) 10.8 Gbps 8.64 Gbps 1440p@60Hz
DP 1.2
(HBR 2)
21.6 Gbps 17.28 Gbps 4K@60Hz
DP 1.3/1.4
(HBR3)
32.4 Gbps 25.92 Gbps 4K@120Hz
8K@60Hz (w/DSC)
DP 2.0
(UHBR 20)
80 Gbps 77.37 Gbps 8K@60hz HDR >8K@60Hz SDR
4K@144Hz HDR
2x 5K@60Hz

DisplayPort 2.0, in turn, is shooting for 8K and above. Introducing not just one but a few different bitrate modes, the fastest mode in DisplayPort 2.0 will top out at 80 Gbps of raw bandwidth, about 2.5 times that of DisplayPort 1.3/1.4. Layered on that, DisplayPort 2.0 also introduces a more efficient coding scheme, resulting in much less coding overhead. As a result, the effective bandwidth of the new standard will peak at 77.4 Gbps, with at 2.98x the bandwidth of the previous standard is just a hair under a full trebling of available bandwidth.

Putting all of this in practical terms for a moment, for VESA and its member manufacturers then, the new standard opens the door to higher resolution, higher refresh rate, and wider color gamut monitors. DisplayPort 2.0 is fast enough to not just support an 8K monitor without any kind of compression (including chroma subsampling), but it’s enough to do so at 30-bit color, allowing for HDR support even at that high of a resolution. Similarly, 10K monitors at 24-bit color are now possible without compression, and 16K monitors with compression. Overall the applications are about as varied as manufacturers want to go, with options ranging from ensuring there’s sufficient bandwidth for next-gen VR to enabling new daisy chaining setups (daisy chained 5K monitors, anyone?), not to mention even more interesting setups such as mixing USB data with high resolution DisplayPort monitors. Many things which VESA is happy to point out that even HDMI 2.1 can’t do, due to the former’s significant bandwidth advantage (all of this solidly putting DisplayPort back on top in terms of total bandwidth).

DisplayPort 2.0 Under the Hood: Thunderbolt 3, UHBR, & Passive Cables

Diving a bit deeper into today’s announcement, let’s talk about the DisplayPort 2.0 physical layer. For the last half decade or so, VESA members have commented here and there about where the standard might go in the future, and what direction the physical ports would take. Developing the next generation of high bandwidth external interfaces only gets harder and more expensive with each generation, which has increasingly caused the various standard bodies to coalesce around a handful of physical layers and data transmission technologies. At the same time, the physical DisplayPort, which was designed over a decade ago, wasn’t originally designed to scale up to the amount of bandwidth DisplayPort 2.0 will be pushing. As a result every option has been on the table to some degree, including disregarding most of the DisplayPort standard, DisplayPort and all.

The end result then is an interesting compromise, and importantly, one that delivers more bandwidth while retaining backwards compatibility with existing DisplayPort gear. The DisplayPort itself is staying: it and the USB-C connector (via DP alt mode) are both official ports for the new DisplayPort 2.0 standard. And because of this, the number of pins and resulting high speed data lanes is remaining unchanged as well, with DisplayPort continuing to operate over 4 lanes. Finally, the DisplayPort 2.0 standard also retains the technology’s packet-based approach to communications, which means that image data continues to be sent as packets over a fixed bandwidth link, as opposed to pixel-centric pixel clock approaches.

So what has changed to enable DisplayPort 2.0? While the titular DisplayPort itself has stayed, the rest of the physical layer has been almost entirely replaced… with Thunderbolt 3.

Rather than attempting to reinvent the wheel, for DisplayPort 2.0 VESA decided to take advantage of Intel’s existing Thunderbolt 3 technology, which already hits the data rates that VESA was looking for. While initially a proprietary Intel technology, Intel released the technology to the wider industry as a royalty-free standard earlier this year. This allowed third parties to not only create pure Thunderbolt 3 devices without paying Intel, but also allowed Thunderbolt 3 technology to be repurposed for other standards. So whereas USB4 is a more straightforward rebranding of Thunderbolt 3, for DisplayPort 2.0 takes it in a different direction by essentially creating a one-way Thunderbolt 3 connection.

Under the hood, Thunderbolt 3 operates fairly similarly to DisplayPort, with 4 high-speed each lanes carrying packets of information at 20 Gbps. However while TB3 is a true bi-directional, full-duplex link with 2 lanes allocated for each direction, DisplayPort is focused on sending large volumes of data in just one direction: out. As a result, DisplayPort 2.0 reverses the two inbound lanes to outbound lanes, allowing the four total lanes to be combined into a single 80 Gbps link.

Thunderbolt 3 vs. DisplayPort 2.0
  Thunderbolt 3 DisplayPort 2.0
Max Cable Bandwidth 80Gbps 80Gbps
Max Channel Bandwidth 40Gbps
(Full Duplex, Bidirectional)
80Gbps
(Simplex, Unidirectional)
Physical Layer Thunderbolt 3 Thunderbolt 3
DisplayPort 2x DP 1.4 Streams 1x DP 2.0 Streams
Passive Cable Option Yes (20Gbps) Yes (40Gbps)
Interface Port USB Type-C DisplayPort
USB Type-C

Speaking of the link itself, the move to Thunderbolt 3 technology also means that DisplayPort inherits Thunderbolt 3’s signal encoding scheme. Whereas DisplayPort 1.x has always used relatively inefficient 8/10b encoding – resulting in 20% overhead – DisplayPort 2.0 will offer 128/132b encoding, which has just 3% overhead. This is why the practical bandwidth gains for DisplayPort 2.0 are more than just the raw bandwidth gains; the standard doesn’t just get more bandwidth, but it uses it more efficiently. Consequently, at its highest data rate, DisplayPort 2.0 will be able to offer 77.37 Gbps of bandwidth.

But what of cables? Here’s where things get a bit trickier, both for VESA and for users. Thunderbolt 3 pushed the limits of copper cabling, and as a result for all but the shortest runs it requires active cabling, with transceivers at each end of a cable. While effective, this drove up the cost of Thunderbolt 3 cables versus relatively cheap all-copper commodity USB 3 and DisplayPort 1.x cables. By using Thunderbolt 3 as the basis of their new standard, VESA has inherited the cable technology limits of the standard as well.

The answer to the cable question then is that VESA hasn’t really answered it. Instead, they’re focusing on what they can do now with passive cables. All told, the DisplayPort 2.0 actually introduces not one, but three new data rates: 10 Gbps per lane, 13.5 Gbps per lane, and 20 Gbps per lane. Dubbed Ultra High Bit Rate (UHBR), the for free-standing monitors VESA right now is focusing on 10 Gbps per lane (UHBR 10), which will deliver a total of 40 Gbps of bandwidth.

At just half the data rate of full-fat DisplayPort 2.0 (and Thunderbolt 3), UHBR 10 is resilient enough that it can operate over standard passive copper cabling, and cables should have little issue reaching 2-3 meters. VESA has actually been preparing for this for some time now, and UHBR 10 aligns with their previously-launched DisplayPort 8K cable certification program; 8K-certified cables will be able to meet the signal integrity requirements for UHBR 10.

DisplayPort 2.0: UHBR Modes
Standard Raw Effective Cable
UHBR 10 40 Gbps 38.69 Gbps Passive Copper
UHBR 13.5 54 Gbps 52.22 Gbps Tethered
UHBR 20 80 Gbps 77.37 Gbps Tethered

Past that, however, VESA isn’t currently exploring (or at least not focused on) passive cables for the higher bitrate modes. Instead, the group envisions UHBR 13.5 and UHBR 20 being tethered setups: manufacturers would ship devices with an appropriate port/cable already attached. These can potentially be passive cables for very short runs (think laptop docks), or integrated active cables for longer runs. I should note that the group hasn’t closed the door entirely to more traditional passive cable setups for these higher bitrates, but at least for the moment the group doesn’t see very many non-tethered use cases coming to market in the near future.

Tangentially, here, there is one more signal-related changed to the DisplayPort standard. Forward Error Correction (FEC), which was introduced to DisplayPort 1.4 as part of the Display Stream Compression (DSC) standard, is now a core part of DisplayPort 2.0. So on a 2.0 link, FEC will be in use at all times, reflecting the challenge in getting these high speed interfaces to constantly transmit data in an error-free manner.

DisplayPort 2.0 Features: Mandatory DSC, Branch Devices, & Panel Replay

Shifting gears, along with the significant physical layer changes being introduced in DisplayPort 2.0, the standard is also introducing some much more modest feature changes.

First and foremost, Display Stream Compression support is now mandatory for DisplayPort 2.0 devices. Previously introduced as part of DisplayPort 1.4 – and not really hammered out entirely until a couple of years after that – DSC is the group’s standard for “visually lossless” image compression. Operating on small groups of pixels, DSC offers modest compression ratios of around 3:1, with the goal of compressing images just enough to save power and bandwidth without introducing visual artifacts and without adding significant latency.

At any rate, starting with DisplayPort 2.0, DSC is now a core part of the DisplayPort standard. To be clear, 2.0 devices do not have to use DSC – the preference is clearly towards uncompressed images when the bandwidth allows for it – however 2.0 devices must be able to encode, pass, and decode DSC compressed data. This will, over time, lay the groundwork for manufacturers to develop and release monitors that require DSC (at least in certain modes), as they’ll be able to sell monitors knowing that all 2.0 devices can drive them.

Speaking of efficiency, the DisplayPort 2.0 standard is also introducing another vendor-optional feature focused on power efficiency, and that’s Panel Replay. Derived from earlier Panel Self Refresh technologies that are part of the embedded DisplayPort standard, Panel Replay is a partial self-update mechanism that allows a system to only transmit and update the portion of an image that has changed since the previous video frame. Like PSR in eDP, this feature is primarily intended for laptops and other mobile devices, where power consumption and the resulting impact to battery runtimes are important qualities. Transmitting less data reduces not only the amount of energy used chauffeuring bits around, but it also reduces the amount of processing required in a display controller.

Last but not least, DisplayPort 2.0 is also updating how “branch devices” work in the standard. Essentially the splitters in a Multi Stream Transport setup, DisplayPort 1.x required that the branch device be capable of decoding a DisplayPort bitstream, which is not an easy feat with 20 Gbps+ of data. So instead, for 2.0, branch devices are being simplified some, and now will just be able to forward data rather than having to decode it. This should make MST (and daisy chaining) a bit easier to implement overall, as branch devices won’t need to be as complex.

On a final note, ahead of today’s specification release I also asked about the state of variable refresh support on DisplayPort. VESA Adaptive Sync is an optional feature for monitors under DisplayPort 1.x, and it will remain so under DisplayPort 2.0. So manufacturers can continue adding it as a useful feature for their monitors, but there are no plans to make it mandatory.

Coming In Late 2020

Wrapping things up, the latest version of the DisplayPort standard is easily the biggest update to the PC display standard since it launched in 2007. By replacing the DisplayPort physical layer with Thunderbolt 3, VESA has greatly increased DisplayPort’s bandwidth potential, laying the groundwork for 8K monitors and beyond. This update doesn’t come for free, and VESA’s member companies will have to tackle the same kind of high-bandwidth cabling issues that Thunderbolt 3 itself had to address over the last few years, but ultimately it’s a situation that gives the display standard a major shot in the arm in terms of bandwidth, while pushing the PC industry ever so closer towards using a handful of common standards for all high bandwidth I/O.

As for the first retail products, the good news is that this will show up sooner than later. Because the new standard is based on the Thunderbolt 3 physical layer, member companies can hit the ground running on development and testing. As a result, VESA expects the first retail devices to show up in the latter part of 2020, less than 18 months from now.

Source: VESA

POST A COMMENT

119 Comments

View All Comments

  • masimilianzo - Wednesday, June 26, 2019 - link

    So we will see new TB3 controllers with DP2.0 support.
    Curios as to when we will have TB4 based on PCIe 4.0
    Reply
  • brakdoo - Wednesday, June 26, 2019 - link

    Probably not so soon. TB3 cables are already bad. Higher frequencies would be a pain in the ass. Reply
  • repoman27 - Wednesday, June 26, 2019 - link

    Thunderbolt is not “based on PCIe” like that. Thunderbolt 3 controllers can be updated with PCIe 4.0 back ends.

    “Thunderbolt 4” will likely be reserved for an increase in the Thunderbolt signaling rate (currently at 20.625 Gbit/s), which has nothing to do with the PCIe generation of the back end.
    Reply
  • masimilianzo - Thursday, June 27, 2019 - link

    Can you elaborate on that? Sorry I am quite ignorant... Reply
  • Skeptical123 - Friday, June 28, 2019 - link

    Thunderbolt is "”based on PCIe” like that". TB3 combines a PCIe x4 and two DP1.2 signals to reach a 40Gps limit provided the drivers and cable support it. This is a little confusing and took me a while to work out how it works because I could all the need info in one place. To help others I have included some references.

    ““Fundamentally, Thunderbolt is a tunneling architecture designed to take a few underlying protocols, and combine them onto a single interface, so that the total speed and performance of the link can be shared between the underlying usages of these protocols – whether they are data, display, or something else”“ - linked from intel website

    “Thunderbolt combines PCI Express (PCIe) and DisplayPort (DP) into two serial signals,” - wiki “Thunderbolt 3 uses PCIe x4 gen 3 data rate with 128kB header sizes. Two links of (4 lane) DisplayPort 1.2 consume 2x (4 x 5.4 Gbps) or 43.2 Gbps. For both of these numbers, the underlying protocol uses some data to provide encoding overhead which is not carried over the Thunderbolt 3 link reducing the consumed bandwidth by roughly 20 percent (DisplayPort) or 1.5 percent (PCI Express Gen 3). But regardless, adding both together gets you above 40 Gbps.“ If demand goes above 40Gbps the drivers hit their limit and will prioritize the DP single though this is rare. - thunderbolttechnology - intel links to this site on their TB3 page
    So the thunderbolt drivers “tunnels” together upto 4 PCIe gen 3 lanes and two links of DP 1.2
    Reply
  • HStewart - Wednesday, July 03, 2019 - link

    With DP 2.0 aim at 2020 and fact that Thunderbolt is created by Intel and USB4 I believe is also 2020. I would expect that TB4 will work with PCIe 5.0

    Also it important to note the differences in TB3 and DP, TB3 is bidirectional because it more than display where DP is primary display. So I wonder if TB could be change to switch mode and allow all lanes in one direction which connected to display.

    There is of course physical cable limitation of USB-C - so compatibility may limits - but hopefully this means TB 4 has new cable option that improves on that.
    Reply
  • Flunk - Monday, July 08, 2019 - link

    On consumer products? I think it will be a long while. 4K@120Hz is going to be fine for consumer applications for the foreseeable future. I really only see 8K being used for large commercial signage. Reply
  • zanon - Wednesday, June 26, 2019 - link

    I kind of wish the industry would suck it up and finally start to really push for optical. Even decent pre-terminated OM4 fiber is now down to below $.69/foot in bulk, and only a bit more (~$0.75-$0.80/ft) as singles. OM3 is even less. OM4 is good for up to 300 feet (100m) with a standard 100GBASE module, and those are going for under $100 each at this point.

    Yes, an extra $100 on each side for the connector is still significant extra margin right now, but I doubt it will be in the context of 6k-8k monitors for a while or the GPUs needed to drive them for a while. The cable pricing represents major savings *and* far more flexibility, optical cables are thin and go so much farther. Optical transmission also uses a lot less power. And those prices also look to be within the range where massive economies of scale could drive them down significantly. It's not crazy infeasible anymore. It's represent a lot more future growth room too. It really seems like the hacks and compromises needed to keep pushing up bandwidth over external copper are starting to not be worth it, which is a drastic change from even a few years ago but here we are.

    Heck, if we're thinking about reusing layers, it might be really interesting if they did just base a display standard around ethernet (or fibrechannel or something) so that all standard switching hardware and the like could be taken advantage of. Just plug a display into a wall keystone and be able to have full connectivity to wherever you want your computer to be elsewhere in the network with 100 Gbps full duplex? I can see uses for that at scale.
    Reply
  • azfacea - Wednesday, June 26, 2019 - link

    +1 for optical. what is the wisdom in preserving copper when you are paying 100$ for a dam usb cable (and even then not knowing if it will fry a certain port if you connect the wrong thing to the wrong port) Reply
  • zanon - Wednesday, June 26, 2019 - link

    At least for regular networking and peripheral connections there are valid arguments to be made for the value of some power over the same cable too, though I wonder if in an optical data world if a hybrid optical/copper cable (ie., a fiber optic cable with 2-pair just wrapped next to it) would actually be that hard, it'd be less copper and far looser (cheaper) reqs since it'd be exclusively carrying power. But desktop screens, particularly high end desktop screens, always need their own PSU anyway so no bonus there. And like you say carrying a lot of power can also plain be a double edged sword, a lot of crummy USB-C cables out there can fry stuff (and in networking means interference and isolation issues, it's common to do fiber between even close buildings for example just for the optoisolation).

    If we were still talking $400 a pop for a 100G transceiver fine yeah that'd be too much, even with savings from vastly more manufacturing. But at $100 which might get shrunk down to $50-80 over a few years, that's getting to the point where it's practically paid for just by cheaper cables even ignoring every other advantage. Seems within striking range anyway, and initial monitors will probably all be in the $2000+ range too.

    Optical was really tough to go consumer with 8-9 years ago say, back when Intel/Apple were doing the initial TB and it was briefly "LightPeak" instead. Now though?
    Reply

Log in

Don't have an account? Sign up now