While the client SSD space has become rather uninteresting lately, the same cannot be said of the enterprise segment. The problem in the client market is that most of the modern SSDs are already fast enough for the vast majority and hence price has become the key, if not the only, factor when buying an SSD. There is a higher-end market for enthusiasts and professionals where features and performance are more important, but the mainstream market is constantly taking a larger and larger share of that.

The enterprise market, on the other hand, is totally different. Unlike in the client world, there is no general "Facebook-email-Office" workload that can easily be traced and the drives can be optimized for that. Another point is that enterprises, especially larger ones, are usually well aware of their IO workloads, but the workloads are nearly always unique in one way or the other. Hence the enterprise SSD market is heavily segmented as one drive doesn't usually fit all workloads: one workload may require a drive that does 100K IOPS in 4KB random write consistently with endurance of dozens of petabytes, while another workload may be fine with a drive that provides enough 4KB random read performance to be able to replace several hard drives. Case in point, this is what Micron's enterprise SSD lineup looks like:

Comparison of Micron's Enterprise SSDs
  M500DC P400m P400e P320h P420m
Form Factor 2.5" SATA 1.8" ; .2.5" SATA, mSATA 2.5" PCIe, HHHL PCIe
Capacities (GB) 120, 240, 480, 800 100, 200, 400 50, 100, 200, 400 175, 350, 700 350, 700, 1400
Controller Marvell 9187 Marvell 9174 IDT 32-channel PCIe 2.0 x8
NAND 20nm MLC 25nm MLC 25nm MLC 34nm SLC 25nm MLC
Sequential Read (MB/s) 425 380 440 / 430 3200 3300
Sequential Write (MB/s) 200 / 330 / 375 200 / 310 100 / 160 / 240 1900 600 / 630
4KB Random Read (IOPS) 63K / 65K 52K / 54K / 60K 59K / 44K / 47K 785K 750K
4KB Random Write (IOPS) 23K / 33K / 35K / 24K 21K / 26K 7.3K / 8.9K / 9.5K / 11.3K 205K 50K / 95K
Endurance (PB) 0.5 / 1.0 / 1.9 1.75 / 3.5 / 7.0 0.0875 / 0.175 25 / 50

5 / 10

In order to fit the table on this page, I even had to leave out a few models, specifically the P300, P410m, and P322h. With today's release of the M500DC, Micron has a total of eight different active SSDs in its enterprise portfolio while its client portfolio only has two.

Micron's enterprise lineup has always been two-headed: there are entry to mid-level SATA/SAS products, which are followed by the high-end PCIe drives. The M500DC represents Micron's new entry-level SATA drive and as the naming suggests, it's derived from the client M500. The M500 and M500DC share the same controller (Marvell 9187) and NAND (128Gbit 20nm MLC) but otherwise the M500DC has been designed from ground up to fit the enterprise requirements.

Micron M500DC Specifications (Full, Steady-State)
Capacity 120GB 240GB 480GB 800GB
Controller Marvell 88SS9187
NAND Micron 128Gbit 20nm MLC
DRAM 256MB 512MB 1GB 1GB
Sequential Read 425MB/s 425MB/s 425MB/s 425MB/s
Sequential Write 200MB/s 330MB/s 375MB/s 375MB/s
4KB Random Read 63K IOPS 63K IOPS 63K IOPS 65K IOPS
4KB Random Write 23K IOPS 33K IOPS 35K IOPS 24K IOPS
Endurance (TBW) 0.5PB 1.0PB 1.9PB 1.9PB

The M500DC is aimed at data centers that require affordable solid-state storage, such content streaming, cloud storage, and big data analytics. These are typically hyperscale enterprises and due to their exponentially growing storage needs, the storage has to be relatively cheap or otherwise the company may not have the capital to keep up with the growth. In addition, most of these data centers are more read heavy (think about Netflix for instance) and hence there is no need for high-end PCIe drives with endurance in the order of dozens of petabytes.

In terms of NAND the M500DC features the same 128Gbit 20nm MLC NAND as its client counterpart. This isn't even a high-endurance or enterprise specific part -- it's the same 3,000 P/E cycle part you find inside the normal M500. Micron did say that the parts going inside the M500DC are more carefully picked to meet the requirements but at a high-level we are dealing with consumer-grade MLC (or cMLC).

To get away with cMLC in the enterprise space, Micron sets aside an enormous portion of the NAND for over-provisioning. The 480GB model features a total of six NAND packages, each consisting of eight 128Gbit dies for a total NAND capacity of 768GiB. In other words, only 58% of the NAND ends up being user-accessible. Of course not all of that is over-provisioning as Micron's NAND redundancy technology, RAIN, dedicates a portion of the NAND for parity data, but the M500DC still has more over-provisioning than a standard enterprise drive. The only exception is the 800GB model which has 1024GiB of NAND onboard with 73% of that being accessible by the user.

User Capacity 120GB 240GB 480GB 800GB
Total NAND Capacity 192GiB 384GiB 768GiB 1024GiB
RAIN Stripe Ratio 11:1 11:1 11:1 15:1
Effective Over-Provisioning 33.5% 33.5% 33.5% 21.0%

A quick explanation for the numbers above. To calculate the effective over-provisioning, the space taken by RAIN must be taken into account first because RAIN operates at the page/block/die level (i.e. parity is not only generated for the user data but all data in the drive). A stripe ratio of 11:1 basically means that every twelfth bit is a parity bit and thus there are eleven data bits in every twelve bits. In other words, out of 192GiB of raw NAND only 176GiB is usable by the controller to store data. Out of that 120GB (~112GiB) is accessible by the user, which leaves 64GiB for over-provisioning. Divide that by the total NAND capacity (192GiB) and you should get the same 33.5% figure for effective over-provisioning as I did.

Test Setup
CPU Intel Core i7-4770K at 3.5GHz (Turbo & EIST enabled, C-states disabled)
Motherboard ASUS Z87 Deluxe (BIOS 1707)
Chipset Intel Z87
Chipset Drivers 9.4.0.1026
Storage Drivers Intel RST 12.9.0.1001
Memory Corsair Vengeance DDR3-1866 2x8GB (9-10-9-27 2T)
Graphics Intel HD Graphics 4600
Graphics Drivers 15.33.8.64.3345
Power Supply Corsair RM750
OS Windows 7 Ultimate 64-bit

Before we get into the actual tests, we would like to thank the following companies for helping us with our 2014 SSD testbed.

Micron M500DC: Features
POST A COMMENT

37 Comments

View All Comments

  • Samus - Wednesday, April 23, 2014 - link

    I think the price is ridiculous, nearly twice as expensive as the reliable Intel S3500 and almost as expensive as the uber-superior S3700. Makes no sense. Reply
  • ZeDestructor - Wednesday, April 23, 2014 - link

    Lot's of lack of time in some sections...

    Granted, new benchmarks, but IMO that should be split off to a seperate article and the entire thing delayed for publishing to get the tests done. Otherwise, excellent revewing as always.
    Reply
  • okashira - Wednesday, April 23, 2014 - link

    If you want a drive with good speed , low price and amazing endurance, just pick up a used Samsung 830 for cheap.
    People have tested them to 25,000 cycles. That's 10+ PB for a 512GB drive, for just $300 or less. And I suspect their data retention is superior as well.
    Reply
  • Solid State Brain - Wednesday, April 23, 2014 - link

    Thing is, while older consumer drives with quality MLC NAND might appear to have an exceptional P/E rating until failure (which occurs when wear is so high that the data retention gets so short the uncorrectable bit error rate so extreme that the controller can't keep the drive in a working state anymore, not even when powered), there's no way their manufacturer will guarantee such usage.

    On a related note, all consumer Samsung 840 drives (with TLC memory) I've seen pushed through in stress endurance testings posted on the internet have reached at least ~3200-3500 P/E cycles until failure and didn't start show any SMART error before 2800-2900 cycles, which means that the approximate ~1800-2000 P/E rating (for the stated TBW endurance with sequential workloads) for TLC-NAND datacenter enterprise Samsung SSDs drives (@ a 3 months data retention) makes much sense. But again, no way Samsung will offer any guarantee for such usage with consumer or workstation drives. they will just tell you they are tested for consumer/light workloads.

    Real endurance figures for NAND memory in the SSD market has to be one of the industry's best kept secrets.
    Reply
  • AnnonymousCoward - Friday, April 25, 2014 - link

    Ever think of doing a real world test, measuring "time"? Everyone should know synthetic benchmarks for hard drives are meaningless. Why don't you do a roundup of drives and compare program load time, file copy time, boot time, and encoding time. Am I a freakin genius to think of this? Reply
  • MrPoletski - Saturday, April 26, 2014 - link

    Why does every single performance consistency graph say 4KB random write QD 32? Reply
  • markoshark - Sunday, April 27, 2014 - link

    I'm wondering if any testing is done with a 30/70 read/write ratio - Most i've seen is 70% read.
    With enterprise drives, they are often rebadged and used in SANs - Would be interesting to see how they compare in write-intensive enviroments (VDI)
    Reply

Log in

Don't have an account? Sign up now