Improved Baseband - No Deathgrip

We’ve mentioned already that the 4S is more of an evolution of the CDMA iPhone 4 than the GSM/UMTS iPhone 4, and where that’s most obvious is again is its cellular architecture. When we reviewed the GSM/UMTS iPhone 4, we investigated and explained why its design made it especially prone to unintended attenuation when held a certain way. Apple remedied the situation somewhat by giving away free cases, but only in the case of the CDMA iPhone 4 was the fundamental design issue remedied by adding receive diversity with a second cellular antenna at the top.

The 4S builds on this architecture by incorporating the same diverse receive path with two U shaped antennas at top and bottom, and adding transmit diversity to the equation. I’m being a bit fast and loose with the term “diversity” here, since the 4S cannot transmit simultaneously on both antennas, but rather switches between the two antennas based on which has the least receive fading. Receive diversity is a bit more interesting to explain, since the 4S appears to be able to dynamically decide whether to select one of the two receive paths (in the case that one is much more faded than the other), or combine the two (using something like maximal-ratio combining) and get a better quality equivalent signal.

When I talked about the CDMA 4’s receive diversity scheme, I went into detail to prove that this feature was present. With the 4S, these diversity features are much easier to talk about because Apple has been directly forthcoming about the feature this time. In addition, the transmit switching part of the equation is discussed at length in Apple’s FCC disclosure (since the FCC is interested in scrutinizing transmitters), and even includes a nice diagram.

The device is capable of switching between the Primary/ANT1 and Secondary/ANT2 Antennas. The antenna switching is implemented with a physical, "break-before-make" switch such that only one antenna can be used for cellular transmission at a time.

To re-state the evolution that Apple has taken with this design, the GSM/UMTS 4 had one transmit and receive chain, the CDMA 4 added a second receive chain for diversity, and the 4S now has two receive chains and the ability to switch between two transmit chains. The result is that the phone no longer is prone to fading on either the forward or reverse link due to being held near the feed points for one chain.

To be totally thorough, you can immediately see that the 4S still incorporates the same overall design however, complete with a a U.FL connector at the bottom and a feed cable that runs up the side of the PCB to the top. From here it obviously terminates somewhere that makes contact with the top antenna.


Encircled in red: Top antenna feed cable (Original photo courtesy iFixit)

When we saw that the CDMA iPhone used Qualcomm’s MDM6600, we made an educated guess that the next device would likely be based on the same baseband. It turned out that this was pretty close to the case, as the iPhone 4S uses an unannounced Qualcomm MDM6610.


Encircled in blue: Qualcomm MDM6610 and PM8028, Red: Bottom antenna U.FL connector. Note to the right the two test pads for the two chains. (Original photo courtesy iFixit)

There are some immediate differences that stick out about MDM6610 versus MDM6600. First, 6610 doesn’t appear to include an internal transceiver, unlike MDM6600 which previously included a transceiver in its package. MDM6610’s package is correspondingly smaller, at 10x10 mm, compared to 6600’s 9.8x12.2 mm, but again you have to factor in the fact that the transceiver isn’t inside that package anymore. Based on those facts and the state of 28nm maturity, it’s almost certain that MDM6610 is still a 45nm part. The 4S uses Qualcomm’s RTR8605 IntelliCeiver transceiver for cellular RF management and also for GLONASS/GPS. We’ve seen RTR8600 before, and RTR8605 appears to just be an improvement upon that part with the same functionality. In fact, inside the MDM6610’s AMSS it’s just referred to as RTR8600.

Qualcomm isn’t ready to talk at all about MDM6610, but I’ve done a little digging and know more about this part. First off, it’s referred to as codename “Trek” inside the Qualcomm AMSS (Advanced Mobile Subscriber Software), whereas MDM6600 in the CDMA iPhone was referred to as “Phoenix.” When we first saw that the 4S was using a baseband that hasn’t been announced, we assumed it was an Apple specific one-off. However, after some digging I uncovered a reference to a GSM/UMTS only part as well: “MDM6210MDM6610”. For those that aren’t familiar, the 2 connotes GSM/UMTS compatibility, 6 adds 1x/EVDO. Apple appears to have secured MDM6610 exclusivity for the time being, but I expect we’ll see a more formal announcement of the MDM6x10 family down the road. This is pretty much par for the course for Apple when it comes to component sourcing.

iPhone 4S - Network Support
GSM/EDGE Support 850 / 900 / 1800 / 1900 MHz
UMTS/HSDPA/HSUPA Support 850 / 900 / 1900 / 2100 MHz
HSDPA/HSUPA Speeds 14.4 Mbps / 5.76 Mbps
CDMA2000 1x/EVDO Support EVDO Rev.A (800 / 1900 MHz)
Baseband Hardware Qualcomm MDM6610

MDM6610 also appears to inherit all the air interfaces that MDM6600 had, including WCDMA/HSPA+ with HSDPA 14.4, HSUPA 5.76, GSM, CDMA 1x/EVDO (up to Rev.B, though Apple notes only A is used at present), and finally GPS/GLONASS. Superficially, there don’t appear to be any major differences beyond using an external transceiver to accommodate diversity and transmit switching. In addition, the 4S contains all the same bands as the GSM/UMTS iPhone 4.

I was initially worried that Apple would go the same route that it did with both iPhone 4 launches and initially not include FieldTest. Thankfully, the 4S includes FieldTest right out of launch, which works for both CDMA and GSM/UMTS provisioned 4Ses.

 
iPhone 4S Field Test under CDMA Mode

There’s a corresponding difference in the interface for the two modes. On CDMA iPhone 4S mode, there are tabs for 1x and EVDO, and Rx signal strength fields for both receive paths, as well as the current transmit power. What’s interesting here is that when using the 4S in CDMA mode, you can see the receive strength change for each antenna when held.

 
iPhone 4S Field Test under UMTS/GSM Mode

On the GSM/UMTS provisioned iPhone 4S, you don’t get individual receive strength for each chain, instead just the effective RSCP from either the selected chain or combined. If you grip the phone while watching this, you can sometimes watch RSCP race to –130 dBm and then switch entirely to the other antenna and race back up to an acceptable number. As a reminder, to get into FieldTest dial *3001#12345#* - you can then keep numerics instead of bars in the top left by force quitting FieldTest after launching it (hold down power/lock until power off appears, then hold the home button).

So how does the 4S do in our actual attenuation testing? Very well actually. I watched the RSCP of one NodeB and held the 4S all the same ways we’ve done since the 4, recorded a bunch of data, and averaged it together. What we’re measuring here is reported in dBm, and less attenuation is better (0 dBm = 1 mW).

Signal Attenuation Comparison in dB - Lower is Better
  Cupping Tightly Holding Naturally Holding in Case On an Open Palm
iPhone 4S 10.8 8.8 - 4.3
CDMA iPhone 4 16.5 15.5 9.0 7.9
GSM/UMTS iPhone 4 24.6 19.8 7.2 9.2
Samsung Galaxy S 2 18.4 5.9 - 12.2
Droid 3 16.0 11.3 - 5.0
HTC Sensation 15.0 10.0 8.0 0.0
Samsung Droid Charge 10.0 10.0 5.0 0.0
HTC Thunderbolt - LTE 5.3 2.5 - 4.4
HTC THunderbolt - EVDO 6.5 0.8 - 7.2
LG Optimus 2X 13.7 9.3 - 5.9
Nexus S 13.3 6.1 - 4.3
Droid 2 11.5 5.1 - 4.5
BlackBerry Torch 15.9 7.1 - 3.7
Dell Streak 14.0 8.7 - 4.0
Droid X 15.0 5.1 - 4.5
iPhone 3GS 14.3 1.9 3.2 0.2
HTC Nexus One 17.7 10.7 7.7 6.7

When we reviewed the CDMA iPhone 4, I made mention of the fact that this was the first iPhone 4 I felt comfortable using without a case. This same confidence continues with the 4S, which is in practice completely usable without a case, unlike the GSM/UMTS iPhone 4. Since launch time, Anand and myself have been using our 4Ses without cases, and the difference is dramatic.

Introduction Faster Throughput on WCDMA
POST A COMMENT

199 Comments

View All Comments

  • thunng8 - Thursday, November 3, 2011 - link

    You do realize that the top 3 results are all vsync limited? They are all close to 60fps. That makes it not a great test to show the full potential of the gpu. Reply
  • ReverendDC - Friday, November 4, 2011 - link

    I was wondering why there were no WPs in your comparison. They have comparable screens, functionality, and features.

    This is NOT to start a flame war. I am curious about how some of the newer WPs especially line up (Titan, Lumina 800, Focus S, etc).

    Thanks!
    Reply
  • mymomentummedia - Sunday, November 6, 2011 - link

    Here is a 360 degreee review of the iPhone 4s with a beautiful girl in a swimsuit... no complaints here.

    http://www.youtube.com/watch?v=-eNxXBIV9_s
    Reply
  • yeatzeck - Sunday, November 6, 2011 - link

    According to the Chipworks (http://www.chipworks.com/en/technical-competitive-... in iPhone 4S is Sony's camera (they even X-ray it).
    You probably have to update the review.
    Reply
  • mosmov - Monday, November 7, 2011 - link

    You've run the Taiji for many devices so far.
    I'd like to see the number also for 4S to align the result with other devices in my memory.
    Reply
  • tipoo - Monday, January 2, 2012 - link

    Taiji is for Android... Reply
  • Conficio - Monday, November 7, 2011 - link

    Text dictation is a neat feature for sure, but to be honest I’m still not likely to rely on it for sending or replying to messages. It’s convenient while driving but the accuracy isn’t high enough to trust it with sending messages to important contacts.


    Here is the viral tip for Apple (or its competitors). Make it an option to deliver the text as well as the ability for the recipient to actually listen to the voice command recorded (sans the edit commands, etc.) That will become fast the fastest way to leave voice messages, because you don't have to wait for the phone to dial, time out and get through the voice mail instructions.
    Reply
  • HelloChris - Monday, November 7, 2011 - link

    Long time reader, but something in this review made me register a username so I could add to the comments...

    Anand's webpage-refreshing battery life test saw the iPhone 4S achieve around 10 and 11 hours, for 3G and WiFi, respectively. However, MANY new 4S owners (including myself) have been getting battery life which is roughly half of that. I just finished reading this whole review, and I have to wonder if the test unit sent to Anandtech might have been hand-picked by Apple? 10/11 hours is just so much more than everyone else seems to be getting. I've averaged 6.5 hours of total usage, and this includes several hours of use where I'm using absolutely no 3G/WiFi data, and minimal processing power (example: viewing a PDF, viewing pictures, reading items on my Google Reader feed)...

    If you look on the major apple forums there are multiple threads where there are many users experiencing the same conditions.

    Also, I'm aware of the battery issue with iOS 5 (which Apple acknowledged last week and has a beta update out already for) which implies that this is indeed a software, not a hardware issue.

    Perhaps I'm missing something, but if it's the case that AnandTech received a well-performing test unit, that would explain their extraordinary battery life.
    Reply
  • doobydoo - Friday, December 2, 2011 - link

    I think you answer your own question.

    It sounds like your phone is affected by the battery life issue for which a software patch has been released, wheras Anand's probably wasn't.

    The vast majority of iPhone 4S owners didn't experience any issues with battery life.
    Reply
  • medi01 - Tuesday, November 8, 2011 - link

    To care about "improved vibration" I have first to be somehow concerned with current "unimproved" vibration. Which I don't. And I don't know any person that is. Reply

Log in

Don't have an account? Sign up now