Samsung 245T: LCD Prime

by Jarred Walton on February 7, 2008 1:00 AM EST

Appearance and Design

The Samsung 245T takes the traditional approach when it comes to appearance. The frame is a glossy black plastic with a matte black stand. Some might go as far as calling the stand clunky looking -- it reminds us of the original Dell 2405FPW stand -- but it does everything that's required. The only truly noteworthy omission is that there is no cable management system at all, so the cables just hang loose off the back of the monitor -- nothing a few zip-ties won't fix, if that's a serious concern.

At the bottom right of the LCD, there are six buttons for accessing the on-screen display (OSD). Skipping the power button at the far right, which functions exactly as you would expect, the left button is a shortcut for enabling/disabling MPA. MPA stands for "Motion Picture Acceleration" and enabling it hopes to improve pixel response times. We'll find out later if it actually makes any noticeable difference in gaming as well. The second button brings up the main menu, and the next two buttons navigate through the menus. Pressing the menu button also exits out of submenus, while the fifth button (Source) acts as an enter button. When no other menus are active, the third button is a shortcut to cycle through the seven available color modes: Custom, Text, Internet, Game, Sports, Movie, and Dynamic CR. The fourth button also functions as a quick access to brightness levels, and the source button switches between available inputs -- note that if nothing is connected to an input, you can't switch to it without going through the full OSD menu. The Auto button is only useful in analog modes, where it will auto-adjust the screen size and centering, and the final PIP button turns on/off picture-in-picture.

As mentioned earlier, the 245T supports the usual assortment of tilt, pivot, rotate, and height adjustment functions. You can see the range of motion available in the above images.

Most of the input ports all face downwards on the back of the display. The exception is the component input ports, which are on the left side of the display next to the four USB ports.

One nice feature of the stand is that it does allow you to raise the panel high enough that it can easily rotate into portrait mode. With some LCDs, we have found that you have to tilt the panel backwards as well as raising it to maximum height before you can rotate the display. If you find yourself frequently using portrait mode, the Samsung 245T would be a very good choice. Note also that the lack of cable management makes it easier to pivot the display.

We created a gallery showing all of the OSD menus and submenus, which you can access below. Most of the OSD functions are straightforward, but there are a few items worth pointing out.

First, there are multitudes of color adjustment options available. Not only can you adjust RGB levels, but you can also tweak hue and saturation via six color controls. We tend to find that amount of control more overwhelming than anything, but it's easy enough to ignore it and if you actually need such functionality it's there. Unfortunately, the second noteworthy item is a black mark; panel resolution scaling only offers two options: Wide or 4:3. "Wide" would be more appropriately named "stretch", as it will attempt to stretch any resolution to fill the entire screen -- without regards to aspect ratio. 4:3 on the other hand will fit any resolution into a 4:3 aspect ratio -- including 16:9 and 16:10 aspect ratios, even digital ones. What this all means is that sticklers who want 16:9 films not stretched vertically will be out of luck; similarly, people who connect an Xbox 360 or PS3 may be disappointed with the slightly stretched widescreen resolutions. What's missing from the scaling options are 1:1 (i.e. no stretch at all, giving black borders on all sides at lower resolutions) and proportional scaling (i.e. a 720p input would scale to fill 1920x1080, leaving black borders on the top and bottom edges) -- both of which are found on competing LCDs.

Update: The aspect ratio options are similar to what we found on the Samsung 2493HM when using the other input sources. In other words, 1:1 stretch is available on VGA connections. We no longer have the LCD, so we can't test the other inputs, but you can read the Samsung 2493HM review for more details.

Features and Specifications Subjective Evaluation
Comments Locked

60 Comments

View All Comments

  • nubie - Thursday, February 7, 2008 - link

    In most proper drivers you can select a mode that has 1:1. In the nVidia classic panel (I only use the classic panel, google sedonadisable if you can't find yours.)

    Use DVI or HDMI, and go to device adjustments, there is a setting called "centered output", use this to send black pixels to fill the digital signal until the pixel ratio is 1:1.

    I ran into a problem that wouldn't allow me to run custom resolutions, this is the fix:

    http://wikitechia.org/wiki/The_custom_resolution_c...">http://wikitechia.org/wiki/The_custom_resolution_c...

    I agree that scaling technology needs serious work, 16:10 is not 16:9, and 1388x768 is not 720p. Add to that the fact that even if you can get the native res of some panels to be sent by the PC, the display still stretches and overscans it, that is bad.

    Doesn't the Xbox360 have support for native panel resolutions such as 1280x1024 as part of the VGA output? Doesn't this extend to the HDMI output? I would really like to know what support there is for native panel resolutions on consoles.

    Every PS3 and Xbox360 I have ever seen has had mediocre picture quality, and I sincerely hope that it is a problem on the display side (in-store displays only).
  • JarredWalton - Thursday, February 7, 2008 - link

    I don't think consoles support PC resolutions. They are usually HDTV/TV resolutions, so you get 640x480 on the old stuff, and 720p or 1080i (or maybe 1080p?) on new stuff. Of course, some titles use a lower resolution like 1024x576 or something and stretch that to 720p/1080p for performance reasons.

    The 245T will accept other resolutions; the problem is that your only options are "fill the whole screen (and aspect ratio be damned)" or "fill a 4:3 area (again, forget about the actual AR)". With PC connections, you're fine if you use the driver to adjust the stretch options.

    Unless I'm severely mistaken, you don't get that functionality with consoles. Or DVD/Blu-ray/HD-DVD players.
  • nubie - Thursday, February 7, 2008 - link

    WRONG!!! Information available as of 2005:

    http://hardware.teamxbox.com/reviews/xbox-360/40/X...">http://hardware.teamxbox.com/reviews/xbox-360/40/X...

    1024x768
    1280x720
    1280x768
    1280x1024
    1360x768

    I was simply curious as to whether recent updates to the Xbox360 firmware had made it MORE compatible.
  • JarredWalton - Thursday, February 7, 2008 - link

    Interesting - didn't know consoles supported other output resolutions... though it seems like it would be game dependent, right? (I'm pretty much a PC-only gamer, so I haven't owned a console since the N64.)

    If you can output 1360x768, you should be able to get a 16:10 AR that will fit with this display properly. That's what I would go for, anyway.
  • JarredWalton - Thursday, February 7, 2008 - link

    Playing DVDs, you can usually control this with your player software, and in fact you can control this with NVIDIA and AMD graphics cards (though I'd give the edge to NVIDIA here) under Windows. The problem is what happens when you hook up something like a game console, or some other device that doesn't do internal scaling. Then you're stuck with what the LCD firmware provides, and in this case it falls short.

    I'd think Samsung could release updated firmware to address this issue. Will they, and if so can you apply it to the initial models? Probably not, but they may prove me wrong.
  • SilthDraeth - Thursday, February 7, 2008 - link

    Click on about above the Forums link, then on the next page, click on intellitext and then choose the option to turn it off.

    Problem solved.
  • Welshtrog - Thursday, February 7, 2008 - link

    I have tried about 10 times and the B***** thing will NOT turn off
  • GTMan - Friday, February 8, 2008 - link

    You probably have to enable cookies.

    Or get a good hosts (google "hosts") file to block lots of ads. There is also a little program called Homer which will replace the blanked ads with a color gradation.
  • Welshtrog - Thursday, February 7, 2008 - link

    I have tried about 10 times ant the B***** thing will NOT turn off
  • AmishElvis - Thursday, February 7, 2008 - link

    Those drop down ads are a deal breaker for me. Get rid of them or I will find another tech review site.

Log in

Don't have an account? Sign up now