Inside Microsoft's Xbox 360
by Anand Lal Shimpi, Kristopher Kubicki & Tuan Nguyen on November 16, 2005 5:09 AM EST- Posted in
- Systems
Removing the Outer Shell
The first step is to remove the outer plastic shell that conceals the innards of the system. To do this, you must start by removing the face plate. Take a look at the front of the Xbox 360 and insert your thumb into the door that covers the two USB ports on the right of the unit. With your other hand squeezing the upper and lower sides of the face plate, pull out the face plate with your thumb. With not much force, the face plate should pop right off.
After the face plate has been pulled off you will see a silver Microsoft sticker covering a gap; remove this. You will also see four small clips locking the top half of the plastic shell to the bottom half. Do not attempt to wedge the clips out at this point.
With some care, gently bend outwards, the right gray ventilation shield on the right side of the unit so that you can see a bit inside. You will notice that the gray side piece attaches to both the bottom and top white chassis. Now look through the holes on top of the unit to locate the areas where the gray side pieces attaches to the white body. What you need to do is take the long but thin metal stick and push down, through the white holes (located on both the top and bottom of the Xbox 360) where the clips of the gray side pieces connect. Slowly pull out the gray pieces away from the unit while unlocking the clips and eventually the gray piece will release itself.
To remove the left gray piece, you must first remove the hard drive unit by pressing the button located on the unit itself. Then apply the same procedure used to remove the right gray ventilation piece -- except when you reach the bottom clip of the piece, you most remove the rubber feet located directly below, to reveal a hole where you can insert the metal stick.
Once you have both side gray pieces removed, you have essentially removed the main locking mechanism that holds the top and bottom shells together. At this point, return to the front of the unit and turn the entire unit upside down. Using a flat head screw driver or wedge, gently pry up the 4 clips holding the top shell to the bottom. Once the clips are unlatched, slowly lift up the front of the bottom shell about an inch.
The last step to removing the bottom shell cover is to insert a thin and small plastic stick into the thin rectangular holes on the rear. The reason the front of the bottom shell needs to be lifted is to prevent the rear latches from reattaching themselves. Slowly insert the stick into each rectangular opening. You should hear a click sound for each clamp you unlatch. Once complete, you may lift off the bottom shell covering.
Looking inside the unit, you will notice that there are 14 silver screws (6 of which are long) and 8 black screws. Using your torx screw drivers, remove the silver screws using a size T12 screw driver and the black ones using a size T7. Once you have all the screws removed, flip the Xbox 360 right side up and lift up the top plastic shell. You should now be greeted with the internals of the Xbox 360.
Facebook
Twitter
RSS
91 Comments
View All Comments
DrZoidberg - Wednesday, November 16, 2005 - link
Aww.. u guys shouldnt say that. Now it doesnt sound that amazing anymore.
24 pipe x800 doesnt sound as good as 48 pipe x1800xt.
Still great work disassembling console. It looks like it takes a while to disassemble it. Would this mean it would be hard to mod xbox360?
jkostans - Wednesday, November 16, 2005 - link
Well if a 700MHz P3 with 64mb ram and a geforce 4 can run doom 3 then imagine what you can do with mid-range hardware today. There is a lot of processing power in that box, especially for the price. I mean yeah a high-end PC is more powerful, but that's the way it's always been. I'm not a console person, mostly because I like shooters and a mouse/keyboard is completely necessary. Did microsoft change their policy towards keyboards and mice? I would love to lay the smack down on my friends in halo, but gamepads suck! Also whatever happened to the console being able to play with a pc over the internet? Didn't dreamcast have something like that?coldpower27 - Wednesday, November 16, 2005 - link
Heh, they should say that if the computational power of each pipeline is inferior to the dedicated Pixel/Vertex Pipes used in the R520. They are more versatile in the fact that they can execute both pixel/vertex shaders, but in exchange for that versatility each pipe is made more simple, and there are more of them over conventional GPU's.CZroe - Wednesday, November 16, 2005 - link
Why didn't they take apart the HDD unit's enclosure? Wouldn't be any less interesting. I'd sure like to know what brand, size and interface it uses. True capacity?DRavisher - Wednesday, November 16, 2005 - link
Have I understood correctly that the GPU and CPU share a 22.4GB/s 512MiB memory? Isn't that kind of low compared to PC graphics?Pythias - Wednesday, November 16, 2005 - link
Nope. Its on par with low/midrange. But they be making games with it for years to come. Unlike the current flavor of the month gpu.
Slaimus - Wednesday, November 16, 2005 - link
The article says the chip has the processing power of a 24-pipeline R420, but only about 1/3 of its memory bandwith. Although you do have to keep in mind the bandwith that does not get wasted on AA thanks to the daughter chip.lexmark - Wednesday, November 16, 2005 - link
with the tedious security features, i wonder how many people will bother modding with the new $399 version...BigandSlimey - Wednesday, November 16, 2005 - link
Looking at the internal shots it highlights the huge area taken up by the DVD drive, I wonder if they used laptop DVD drive tech, they could've made the console much smaller.tuteja1986 - Wednesday, November 16, 2005 - link
yeah... but then we would get a crappy laser that would die !