Biostar iDEQ 210P (cont'd)

Construction


Click on images to enlarge.

The construction of the iDEQ is very good in most areas. The case panels are made of aluminum and can actually be removed in sections. The side panels need to be removed before the top panel can be taken off, which depending on your view, is either good or bad. It's a bit easier to remove the sides than a large, bulky cover, but the top is still a little awkward to remove/install, and you now have to deal with three panels instead of one. You can install/remove RAM and hard drives with just the sides removed, but for the CPU and optical drive, you need to remove the top panel in order to access the internals properly. In the end, it's not really good or bad, just another alternative.

The HSF itself is an all-copper design again - a theme among SFFs, as copper dissipates heat better and the confined space makes such a property desirable. As with the Aopen HSF, there are heatpipes to help draw heat away from the base plate, and the fan is a side-mounted unit. Unlike the Aopen, the CPU HSF does not blow directly at a side panel, but instead, blows towards the rear of the case where a case fan can then exhaust the warm air. With the power supply fan, then, the iDEQ ends up having a total of three fans. This may add slightly to the noise levels, but in practice, it wasn't much different from other units.

The frame is well built, similar in many ways to the Aopen and Shuttle cases. It's relatively lightweight, but still gives a feeling of durability. The weakest point of the construction is once again the front panel. It is composed of plastic mostly, with metal used in a few places. The sliding door that we mentioned earlier does not have a feeling of durability. Over time, we would not be surprised if the faceplate begins to slip down on its own, due to its weight and the cheap-feeling slide mechanism. This didn't happen with our unit, but then, we're dealing with a short period of use as opposed to months or years of continued use. The door has an aluminum cover glued on, which looks nice, but only exacerbates the problem with its added weight.

All is not lost with the front panel, however, as the lower hinged door that covers the front ports feels a lot more durable than the sliding door. We would prefer a design that allowed the door to fold up into the case rather than lying flat, but there are issues with either design. With the lower door, the latching mechanism has a clamp that opens when you press the door in and then closes when you press the door in a second time. The hinges are still plastic, so it could break off easier than if metal were used. We get the impression that it will last longer than the sliding door, at least.

Setup


Click on images to enlarge.

The iDEQ is pretty similar to most of the other cases in terms of setting it up. The panels are removed in three parts, and you can actually install the optical drive and other components without removing the CD/floppy cage. Getting at the CPU socket can be a little difficult that way - particularly if you have large hands - but it's not that bad.

In the convenience segment, the panels are all attached with thumb screws, as is the hard drive bracket. The sides are also interchangeable, but that's not really useful. The one panel has the vent holes toward the front of the case and the other side has them toward the rear; as you will want the ventilation holes to line up with your graphics card in most configurations, the panel with the rear vents should be on the AGP side. Also worth noting is that power cables for the HDD area are pre-installed, with two SATA and two molex connectors available. It's a little odd to have four power connections routed to an area where at most, two could be used, and the extras only end up getting in the way. Still, the option to easily use either SATA or ATA drives is appreciated. The IDE data cables are also pre-installed, but the SATA cables are not. This is a good compromise if you want to use IDE drives, but for SATA use, the IDE cables just add clutter. This is really a "Catch-22" topic, since not having IDE cables pre-installed makes the user spend time and effort getting them cleaned up. Given that the HDD bays are not as far away as the optical bays, though, we don't mind having to route it ourselves, particularly since we generally recommend SATA drives anyway.

The expansion card covers on the iDEQ are, simply put, not the easiest to work with. Not only are there screws to secure the cards, but there is also a hinged "door" that you have to lift up to be able to install or remove cards. Getting the door to line up with the screw sockets once you've installed a graphics card requires a bit of effort, and even if you only want to change out the graphics card, you have to remove both screws. We would prefer an extra half inch in the length of the case in order to do away with the door, and even better would be some sort of tool-less retention mechanism. Unfortunately, many other cases use this same setup for the expansion slots.

Software installation was simple enough, although it required a bit more user interaction than the Aopen system. The System Control utility included on the CD is a required install in our opinion, as it helps to monitor the system temperatures and fan speeds better. Without the utility installed, the system fans run at a higher speed. We would prefer to have the BIOS control fan speed without any additional software, but the utility does offer several options for tweaking fan/noise performance within Windows, which some people will prefer.

Noise, Heat and Performance

In the noise department, the iDEQ is similar to most of its rivals. However, unlike all of the Intel alternatives that we're testing in this roundup, integrated graphics are not included and an add-in graphics card will be required. With the X800 Pro installed, the noise levels were still some of the lowest of the units reviewed, and use of a fanless MX440 helped to bring the unit to near-silent levels. Again, note what we said above about installing the System Control utility, as it reduced noise levels significantly. Heat did not appear to be as big of a concern with the iDEQ, which can be explained at least in part by the CPU platform. The Athlon 64 is usually not quite as hot as the Pentium 4. The combination of heat and noise is really what we're interested in, however, and with no instability problems, we're fine with the moderate heat levels that we measured.

Performance, not surprisingly, was at the top of this roundup. Of course, this is an apples-to-oranges comparison, since this is the only Athlon 64 platform that we're testing. The CPU is also rated at 3200+, giving it an added advantage over the Pentium 4 3.0 used in the other systems. If you want the fastest possible SFF platform right now, AMD platforms lead in most benchmarks - just like in the desktop world - and the iDEQ is clearly the best gaming system in this roundup. Socket 939 SFFs will be reviewed in a separate roundup, but again, the price/performance of socket 754 is still very competitive.

Overall Impressions

The iDEQ doesn't have any major extras included, but it does have all of the high quality standard features that we like. The inclusion of a mini-PCI slot is also interesting, as is the larger power supply and space for two hard drives. The design of the front panel is our biggest complaint, and even then, it's not a deal breaker. Speaking of deals, the online price of around $260 is very competitive. If you're looking for a unit that includes integrated graphics, you're probably better off with an Intel system, but if you plan on adding a higher performance card anyway, or perhaps an all-in-one solution with VIVO, that isn't too important. Given the number of SFF cases that Biostar makes, we would encourage them to at least offer one design that takes a more conservative approach to appearance and omits the sliding door mechanism. We like the features offered, and a modified front panel ought to be relatively easy to design.

Biostar iDEQ 210P Foxconn e-bot
Comments Locked

32 Comments

View All Comments

  • Midian191 - Tuesday, February 15, 2005 - link

    The latest bios version of the 210P has voltage control and bios control of the fan speed.
  • OrSin - Tuesday, February 15, 2005 - link

    If you want smaller review a mini-itz systems.
    They are pretty weak, but it depends what you want to use them for.

Log in

Don't have an account? Sign up now