Basic Features: DFI nForce4

DFI uses the same PCB for all nForce4 models. This assures that the overclocking capabilities of all the nForce4 boards are the same. In fact, all boards use the same BIOS. The 3 DFI nForce4 models are:
  • LANParty nF4 SLI-DR
  • LANParty UT nF4 SLI-D
  • LANParty UT nF4 Ultra-D

Models with the SLI name feature the nVidia nForce4 SLI chipset, while those with Ultra use the nF4 Ultra chipset. All boards feature dual PCIe slots, and the "R" in the SLI-DR adds Silicon Image 3114 4-drive SATA RAID. The two LANParty UT models are identical except one uses the SLI Chipset and the other uses nF4 Ultra.

We tested production models of the top and bottom of the DFI nForce4 lineup, and we can report that performance of these two models was exactly the same in all our benchmarks. Your choice, therefore, should be based on the SLI/Ultra choice and other features. In addition, those who are willing to mod a chip can make a minor change to the $140 Ultra-D board and convert it into an SLI chipset with SLI performance identical to the top line SLI boards. Details on this mod are available at Morphing nForce4 Ultra into nForce4 SLI.


 Specification  DFI LANParty nF4 SLI-DR  DFI LANParty UT nF4 Ultra-D
CPU Interface Socket 939 Athlon 64
Chipset nForce4 SLI (single chip) nForce4 Ultra (single chip)
Bus Speeds 200MHz to 456MHz (in 1MHz increments)
PCI/AGP Speeds Asynchronous (Fixed)
PCI Express 100MHz to 145MHz in 1MHz increments
Core Voltage Auto, 0.8V to 1.55V in 0.025V increments (Normal) PLUS
*104%, 110%, 113%, 123%, 126%, 133%, 136% (Special - to 2.1V)
CPU Startup Voltage Startup, 0.825V to 1.550V in 0.025V increments
DRAM Voltage 2.5V to 3.2V in 0.1V increments (3V jumper)
2.5V to 4.0V in 0.1V increments (5V jumper)
Chipset Voltage 1.5V, 1.6V, 1.7V, 1.8V
Hyper Transport Ratios Auto, 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0
LDT Bus Transter 16/16, 16/8, 8/16, 8/8
LDT Voltage 1.2V, 1.3V, 1.4V, 1.5V
CPU Ratios Auto, 4x to 25x in 0.5x increments
Cool'n'Quiet MAX FID Auto, 8.0 to 13.0 in 0.5x increments
DRAM Speeds Auto, 100, 120, 133, 140, 150, 166, 180, 200
Memory Command Rate Auto, 1T, 2T
Memory Slots Four 184-pin DDR Dual-Channel Slots
Unbuffered ECC or non-ECC Memory to 4GB Total
Expansion Slots 2 x16 PCIe Slots
1 x4 PCIe
1 x1 PCIe
2 PCI Slots
Onboard SATA 4-Drive SATA by nF4 PLUS
4-Drive SATA by Sil31144-Drive SATA by nF4
Onboard IDE Two Standard nVidia ATA133/100/66 (4 drives)
SATA/IDE RAID 4-Drive SATA PLUS
4-Drive IDE (8 total)
Can be combined in RAID 0, 1
PLUS 4-Drive SATA by Sil3114
Sil3114 Raid 0, 1, 5
4-Drive SATA PLUS
4-Drive IDE (8 total)
Can be combined in RAID 0, 1
Onboard USB 2.0 IEEE-1394 10 USB 2.0 ports supported nF4
2 1394A FireWire ports by VIA VT6307
Onboard LAN Dual Gigabit Ethernet
PCIe by Vitesse VSC8201 PHY
PCI by Marvel 88E8001
Onboard Audio Karajan Audio Module
based on Realtek ALC850 8-Channel codec with 6 UAJ audio jacks, CD-in, front audio, and coaxial SPDIF In and Out
Other Features Power and Reset momentary switches
BIOS Award 2/01/2005

All of the new DFI boards are based on either the nForce4 SLI or the nForce4 Ultra. More information on nForce4 is available at:

Morphing nForce4 Ultra into nForce4 SLI
NVIDIA's GeForce 6 SLI: Demolishing Performance Barriers
FIRST LOOK: Gigabyte K8NXP-SLI
FIRST LOOK - nForce4: Gigabyte K8NXP-9
nForce4: PCI Express and SLI for Athlon 64
NVIDIA SLI Performance Preview with MSI's nForce4 SLI Motherboard

The DFI boards all support the full range of nVidia nForce4 features including nVRAID, Active Armor, SATAII 3Gb/s drives, NCQ, any-drive IDE/SATA Raid, PCIe Gigabit LAN by a PHY Ethernet chip (plus an additional PCI Gigabit LAN), and the nTune utility.

Packaging for the full LANParty nF4 SLI-DR is typical LANParty.

It is a huge package with a motherboard, UV cables, a system carrier, a Front-X box, and even UV sheathing for your system cables.

The UT provides a more modest package.

The UT does include most of the same features and accessories found in the LANParty SLI-DR, however. The board is the same except it is based on the Ultra chipset instead of SLI and the Ultra-D does not have the additional 4 SATA ports provided by the Silicon Image 3114. You still get the UV cables, and even the same Karajan Audio Module. The missing accessories are the system carrier, Front-X (which will be very important to some) and cable sheathing. If performance is what matters to you, then you can choose any of the new DFI nForce4 boards and then decide what additional features and accessories matter to you.

DFI has continued with the Karajan Audio Module first introduced on their LANP arty 925x. However, we wish that DFI had been able to use the High Definition ALC880 or a similar chip instead of the more common ALC850. The Karajan Module isolates audio for best signal-to-noise ratio and high definition chip benefits most from this isolation.

The Realtek ALC850 7.1 audio chip has appeared on many recent motherboards. This 8-channel audio codec is fully AC '97 2.3 compliant and features 16-bit 8-channel audio and auto-jack sensing with support for a full range of analog and digital IO. The Karajan Module includes both SPDIF in and out coaxial connectors on the rear IO panel. There is also an on-board SPDIF connector for an optical cable.

The ALC850 Codec provides four pairs of stereo outputs, with 5-Bit volume controls and multiple stereo and mono inputs, along with flexible mixing, and gain and mute functions. Two 50mW/20ohm headset audio amplifiers are integrated at Front-Out and Surround-Out, and both amplifiers are selectable for Front-Out, Line-In and Mic-In as a Universal Audio Jack.

You can find more information on the recently released ALC850 atRealtek.

DFI provides a full selection of rear I/O ports. These include 6 programmable audio mini jacks plus coaxial SPDIF in and out connectors to support the Realtek ALC850. The back panel also includes PS2 mouse and keyboard, 1 standard Firewire (IEEE1394a), 6 USB, and two RJ45 Gigabit Ethernet. There are no rear ports for a Parallel Printer or serial devices, but there is an onboard header for an external serial device - an IR header.

On "R" models, like the DFI LANParty nF4 SLI-DR, DFI uses the Silicon Image 3114 SATA controller to add 4 more SATA ports to the 4 already provided by the nVidia nForce4 chipset. The Sil3114 ports can be combined in RAID 0, 1, or 5. RAID 5 can be implemented on this controller with 3 hard drives.

The four DIMM slots support up to 4GB of up to DDR400 memory in a Dual-Channel memory configuration. Dual-Channel 1 is DIMMs 1 and 3, and Dual-Channel 2 is DIMMs 2 and 4. DFI specifies support for both ECC and non-ECC unbuffered memory. Contacts at DFI advise that best overclocking is achieved with the dual-channel DIMMs in Sockets 2 and 4.


Index Board Layout: DFI nForce4
POST A COMMENT

114 Comments

View All Comments

  • ShadowVlican - Wednesday, February 2, 2005 - link

    beautiful analogy #22

    for now i guess this is THE best AMD64 board money can buy... i wonder if Abit's AN8 will change the results...
    Reply
  • PrinceGaz - Wednesday, February 2, 2005 - link

    Can hard-drives be installed in non-RAID mode on the Sil3144 sockets with this board?

    As far as I know, the additional controller on the Asus SLI Deluxe board requires SATA drives to be in a RAID configuration and does not support individual drives. Can you confirm if that is the case with the DFI board.
    Reply
  • erios666 - Wednesday, February 2, 2005 - link

    #49 - Thanks much Wesley. I did actually see that. I still feel it doesn't answer the question of whether or not you can span all those monitors. It will work great for when I'm at work. Which I can accomplish with an AGP plus a PCI vid card. But I am hoping to get some "surround gaming" going in UT2004, HL2 and NFSU2. So *span* capabilites with a 3840x1024 res' I guess is what I'm looking for rather than a simple multi-mon. Reply
  • Zebo - Wednesday, February 2, 2005 - link

    This is what I call a "ten year board" ...a motherboard built to last (jap caps, mosfets, al cooled etc), with every feature imaginable... you DON"T have to be an overclocker to get this board. In fact it's probably the best mobo ever built for the price using componets found in high-end server boards costing hundreds more. You should buy this DFI reguarless if you plan to overclock or not.

    That said... it's overclcoking options leave me speechless..never has a board came with these kind of heavy duty options..2.1 Vcore..4Vdimm..fuggin incredible. And it shows...guys at xtreme are posting over 400HTT with this bad boy.

    Just awesome..you'd have to bee a damn fool to buy any other skt 939 mobo, or any mobo for that matter over DFI...
    Reply
  • Stiganator - Wednesday, February 2, 2005 - link

    Between the A8n-SLI and this DFI SLI board which would you choose? Reply
  • Wesley Fink - Wednesday, February 2, 2005 - link

    #48 - DFI has responded to your question.

    "That's what we call "Dual Xpress Graphics" technology, supporting 2 video cards simulatneously and therefore 4 monitors. The DFI Ultra-D in normal mode will support up to 4 monitors off 2 video cards"
    Reply
  • erios666 - Wednesday, February 2, 2005 - link

    Please please does anyone know if it will be possible to do a 3 monitor span on the Ultra-D?!
    I beg of you! I want to do something like a Matrox Parhelia but with more 3D power. I've already got all my lcds and now I'm just sitting and waiting to see how this all pans out.
    Reply
  • nserra - Wednesday, February 2, 2005 - link

    Athlon 64 3200+ (Socket754) ALL 1003
    Athlon 64 3000+ (Socket754) ALL ALL
    Athlon 64 3400+ (Socket754) ALL ALL
    Athlon 64 2800+ (Socket754) ALL 1003
    Athlon 64 3700+ (Socket754) ALL 1003
    Sempron 3100+ (CG version) (Socket754) ALL 1004
    Sempron 3100+ (D0 version) (Socket754) ALL 1005

    Any one know how sempron 3100+ D0 overclocks?
    Reply
  • Wesley Fink - Wednesday, February 2, 2005 - link

    Instead of answering emails, we asked DFI to name some vendors who would likely have boards this week. They suggested New Egg, Frys (and their outpost.com online store), NCIX, zipzoomfly, and Monarch Computer. DFI also says Tiger Direct and Microcenter will have them by next week.

    That's all we know and it's straight from DFI, so PLEASE stop emailing us asking where to buy. Thanks!
    Reply
  • HardwareD00d - Wednesday, February 2, 2005 - link

    Onboard sound has pretty much always been crap, with a few exceptions (Sound Storm). I wasn't too impressed with Via Envy24 BTW. An add-in soundcard is the best way to go IMHO.
    * waits for Creative to get off there a$$ and make a PCI-e soundcard with Dolby Digital Encoding *
    Reply

Log in

Don't have an account? Sign up now