Fixed Function Changes & Scalability

Zooming out from the ALU, we’re seeing a higher-level block configuration that’s very similar to past Imagination PowerVR GPUs. The ALUs themselves are still housed in the larger cluster block that’s called the USC, or unified shading cluster. The USC along with various other fixed function blocks is in turn housed in an SPU, or shader processing unit, effectively the scaling block regularly referred to as a “core”.

Each SPU houses two USCs in the current IP configuration, meaning we have two clusters of 128-wide ALUs. This is valid for all AXT parts, but we imagine the AXM-8-256 unit just has a single USC. The AXT-16-512 is the smallest configuration with a fully populated SPU.

Each SPU has its own geometry pipeline, and up to two texture processing units. The A-Series carries over the per-TPU throughput design from the Furian architecture, meaning the block is able to sample 8 bilinear filtered texels per clock. The A-Series doubles this up now per SPU and the AXT models feature two TPUs, bringing up the total texture fillrate to 16 samples per clock per SPU.

The microarchitecture of the texture units has also evolved beyond just their throughput. A bigger improvement that Imagination is disclosing is the handling and location of the L0 cache. The L0 cache has been relocated within the texturing workflow to between the processing and filtering stages, allowing the L0 cache to hold the outputs of the processing stage, rather than the inputs. This allows for what Imagination calls significant data reuse, as texels don't need to be re-processed each time they're needed. And given how many times a texel may need to be sampled during anisotropic filtering, it's easy to see why. With the benefit of hindsight, this seems like an obvious improvement to make, but the company says that the design choices of the legacy configuration made sense at the time of conception and the workloads back then.

Imagination also talks about how the anisotropic filtering quality of the new architecture is much improved. In a set of comparison screenshots using a traditional texture tunnel, Imagination is showcasing that its new anisotropic filtering algorithms are far closer to being angle-independent – the ideal outcome for aniso filtering – as opposed to angle-dependent filtering with rather hard 90 degree angles on Rogue. Interestingly, Imagination is claiming that they've achieved this improved angle-independence even with fewer fewer samples, all of which serves to improve their efficiency and hardware density. With all of that said, since the comparison is against the Rogue architecture, I’m not entirely sure if it’s an actual novelty of the A-Series or rather a rehash of the anisotropic improvements that already got introduced in the 9XM series last year.

Another change in the fixed function units is found in the pixel pipeline, although superficially the throughput here doesn’t change compared to what we’ve seen on Furian. There’s still up to two PBEs with throughputs of up to 4 pixels per clock, and the design houses two such units for a total of 8 pixels per clock per SPU. There’s actually more internal distinction of the units though – at the front and back core it’s still able to handle 16 pixels per clock and also blend at 16 pixels per clock, although it’s limited on write out to 8 PPC on 1:1 pixel:texture situations.

Imagination’s doubling of the texture throughput whilst maintaining a steady pixel throughput means that the company is generally matching the decreasing pixel:texel fillrate throughput ratio we’ve also seen in other architectures such as from Qualcomm as well as the new Mali-G77, and now falls in at a 1:2 pixel:texel for the A-series.

Alpha blending is now done on a dedicated hardware unit in the pixel pipeline instead of being computed by the ALUs. The change results in higher performance through the use of fixed function hardware, allowing for things such as FP16 blending at full rate, and frees up the ALUs themselves so that they can use their computation resources on other work. Density is improved, but more importantly it’s also improving power efficiency as it’s avoiding using more expensive and less task-specific hardware for the same tasks.

It’s to be noted that for the AXM series, the company uses customized fixed function units that are more area efficient, rather than just only scaling the numbers of units.

Scaling Things Up

With the SPU being the coarsest scaling block of the architecture, Imagination is building larger GPU configurations by simply adding in more SPUs. Essentially this is the “core” scaling of Imagination's GPU designs.

Scaling of SPUs across the AXT line happens in multiples of 16-512 across the range, both in terms of their product names as well as their texture and FLOPs/clock capabilities, which is rather simple to grasp and very quickly understand a configuration’s capabilities. As mentioned in the introduction, Imagination views the AXT-32-1024 as being the most popular choice for vendors targeting the high-end premium smartphone SoC segment, which possibly some vendors opting to go with the AXT-48-1536 for a larger area and lower clock speeds for more efficiency. The AXT-64-2048 would be a really big GPU which the company could build if there’s costumer interest.

PowerVR GPU Comparison
  AXT-16-512 GT9524 GT8525 GT7200 Plus
Core Configuration
 
1 SPU (Shader Processing Unit) - "GPU Core"

2 USCs (Unified Shading Clusters) - ALU Clusters
FP32 FLOPS/Clock

MADD = 2 FLOPs
MUL = 1 FLOP
512

(2x (128x MADD))
240

(2x (40x MADD+MUL))
192

(2x (32x MADD+MUL))
128

(2x (16x MADD+MADD))
FP16 Ratio 2:1 (Vec2)
Pixels / Clock 8 4
Texels / Clock 16 8 4
Architecture A-Series
(Albiorix)
Series-9XTP
(Furian)
Series-8XT
(Furian)
Series-7XT
(Rogue)

Comparing the smallest AXT-16-512 configuration with a single SPU and two USCs against similar configurations across the generations, we indeed see that the new A-Series does bring large architectural changes.

Imagination is marketing a 4x increase in ALU throughput, but again that’s against the 9XM GPUs, which are equal in ALU configuration to the Series-7XT in the table. However, it’s not to say that the increases aren’t any less impressive when comparing to the previous 9XTP family; a rise from 240 FLOPs/clock to 512 is still a 2.13x increase.

I think what’s actually more important to note here is the architecture has very big building blocks. At 512 FLOPs and 8 pixels per clock, an AXT SPU is significantly bigger than an Arm Mali-G77 core which comes in at “only” 64 FLOPs/clock and 2 pixels per clock, meaning an AXT core is roughly equivalent to eight G77 cores in computational power and four G77s in fillrate throughput, which is a massive difference in terms of design scaling. Naturally, in terms of effective density and power efficiency, few big cores will always win over a flock of small cores, as demonstrated by Qualcomm and Apple’s recent 2- and 4-core designs.

New ISA & ALUs: An Extremely Wide Architecture HyperLane Technology, Other Additions
POST A COMMENT

143 Comments

View All Comments

  • Etain05 - Tuesday, December 3, 2019 - link

    I think that’s for tablets, and the AXT-64-2048 is just a possible option. If you want to consider the AXT-48-1536, you’d have to compare it to the A12X and whatever comes next. Reply
  • vladx - Wednesday, December 4, 2019 - link

    Well B series should be available to customers in 2020 so a BXT-32-1024 should crush the A14 assuming the 30% improvements will be accomplished. Reply
  • Etain05 - Wednesday, December 4, 2019 - link

    The A series will be in devices in the second half of 2020, there’s absolutely no way that the B series will be available to customers in 2020. The B series will be available in 2021, when it will compete with the A15. Reply
  • vladx - Wednesday, December 4, 2019 - link

    By customers I meant SoC manufacturers, like MediaTek and phones using B-series SocS could be made available before A15 since Apple releases new phones in Q4 usually. Reply
  • Etain05 - Wednesday, December 4, 2019 - link

    Even if we were to be generous in our assumptions, the soonest we’ll see any device with a B-series would be Q3 2021, so at most a few months before the A15. The competition would still be the A15, not the A14. Even more importantly, there’s almost no smartphone that comes out in Q3, apart from some in August and September, which is exactly the time when the A15 will be out too. Reply
  • rbanffy - Tuesday, December 3, 2019 - link

    It's still a numeric naming scheme. 0xA comes after 0x9, after all. Reply
  • mode_13h - Wednesday, December 4, 2019 - link

    Yeah, but he asked and they denied it. They should've been like "hey... yeah! yeah, that's exactly right!", except the question was probably fielded by an ignorant marketing drone who doesn't know about hexadecimal.

    In fact, maybe whoever actually thought of the naming scheme planned it exactly like that, but that reasoning somehow failed to get communicated.
    Reply
  • domboy - Tuesday, December 3, 2019 - link

    Oh... so they aren't announcing a new Kyro video card... oh well... :/ Reply
  • mode_13h - Wednesday, December 4, 2019 - link

    Nice one. At first, I thought you confused it with Qualcomm's "Kryo" cores, but misspelled it.

    https://en.wikipedia.org/wiki/PowerVR#Series3_(STM...
    https://en.wikipedia.org/wiki/Kryo
    Reply
  • wrkingclass_hero - Tuesday, December 3, 2019 - link

    I wish them success and hope to see them get plenty of design wins. I have never actually owned a PowerVR product, but I've been sort of a distant fan (over here in Android land) and look forward to seeing how they perform. If they do well, who knows, they may even reenter the console market with the next-gen portables. Reply

Log in

Don't have an account? Sign up now