From time to time you may see either myself, Anand, or one of the other writers post our thoughts on topics in the forums and news articles. Today, we are going to post a bit of "extended coverage" on our thoughts concerning DDR2. Hopefully, you enjoy our new approach and we encourage you to post your comments!

Even before Computex 2003 we began to first hear some of the upcoming strategies incorporating DDR2 into upcoming Intel platforms.  Several months later, in January, we received confirmation on how and when these technologies were going to appear in upcoming chipsets. 

Today Micron, Elpida and Samsung compose of the majority of the DDR2 market.  Unfortunately there is a lot of confusion about the JEDEC specification.  DDR2 is nearly identical to DDR1, with a few optimizations.  The major optimizations include:

  • 4-bit prefetch (up from 2-bit)
  • Enhanced Registers
  • Additive latency
  • FBGA Packaging
  • On Die Termination
  • DDR2 gets the majority of its punch from the 4 bit prefetch.  DDR2 can effectively write/read four times the amount of data per clock cycle to/from the memory array.  This effectively doubles the data bus speed while keeping the internal bus speed the same from DDR1.  Both DDR1 and DDR2 use a 64-bit interface.

    These optimizations come with the advantage of a slightly lower operating voltage, but requires 240 pins rather than the 184 pins required by DDR today.

    With the talk of different bit prefetches, it becomes difficult to tell the actual clocks of the new memory. Briefly stated, DDR2 runs with a lower internal clock than DDR1. However, since the prefetch is larger than DDR1, the external clock is doubled. For example, if we could run the same DDR400 on the shelves today with DDR2's 4-bit prefetch, it would essentially operate at DDR800. Since this is not possible, the internal bus of the DDR2 modules we see now has been lowered to 100MHz for DDR2-400 and 133MHz for DDR2-533. DDR400 and DDR2-400 should perform the same.

    What does this mean for early adopters?  Essentially; nothing. There will not be a performance increase between DDR2-400 and DDR-400 (or even between DDR2-533 and DDR-533).  DDR2 is the technology to enable post-DDR533 speeds, rather than a technology to enhance it. As we start to see benchmarks of DDR1 versus DDR2 trickle in, consider the maturity of the two technologies.  DDR1 is nearly 5 years old with dozens of chipset manufacturers and billions of dollars in financial backing.  DDR2 still has not even entered full production yet.

    DDR2, today, is still not the DDR2 we will see in mass production come April or May.  Not surprising, Intel has pushed its sample 925X chipsets back another couple weeks to cope with compatibility and performance issues on DDR2.  So, even though PC2-4300 does not perform as well as PC-4300 right now, keep in mind the memory controllers still have some significant changes to undergo.  The timings on today's PC2-4300 are also very poor; most Micron based DDR2 is rated as 4-4-4. Regardless, we should not be looking for performance leaps between DDR2 and DDR1 until memory gets up into the DDR2-667 and DDR2-800 ranges.  According to Intel, VIA and SiS roadmaps, we might see all of these speeds this year.

    With DDR2 memory fixed around $900 for 512MB right now, it is probably unlikely that we will see the enormous rush to Intel's 925X chipset.  Even once prices fall to within range of the DDR prices of today, the newer technology will not really benefit the consumer until we get into the speeds unobtainable by DDR1. 



    View All Comments

    • joeld - Wednesday, February 25, 2004 - link

      Good question -why the increase? just to lower the internal megahertz? Reply
    • Pumpkinierre - Wednesday, February 25, 2004 - link

      #13 If it is the same bus width, why the 240 pins? 62 pins more than the ordinary DDR. Reply
    • DerekWilson - Wednesday, February 25, 2004 - link


      all the improvements really are improvements to enhance scalability, not performance.

      Think of it like this: its the same bus width and speed a. You can't do better than moving the maximum ammount of data across the bus in either case.
    • Nighteye2 - Wednesday, February 25, 2004 - link

      It may be nit-picking, but the article mentions 5 improvements, of which only the most influential one will be negated by the lower clock. But doesn't that leave 4 improvements to make DDR2-400 faster than DDR-400, if only marginally so?
    • KristopherKubicki - Wednesday, February 25, 2004 - link

      GDDR2 and GDDR3 are fairly different.

    • skunkbuster - Wednesday, February 25, 2004 - link

      "Actually have been waiting for PCI Express for sometime. PCI does not provide enough bandwidth for all the PCI cards I have installed. PCI Express will be able to provide the bandwidth I need. "

      but unfortunately, you will not be able to use your pci cards in a pci express slot.

    • ViRGE - Wednesday, February 25, 2004 - link

      The doubled prefetch is just for normal DDR2, right? I'm just thinking that we haven't heard anything about this for GDDR2, so it's unlikely this applies to it. Reply
    • jpwoodbu - Wednesday, February 25, 2004 - link

      Is DDR2 really not in mass production? According to ati's website, they're using it on the Radeon 9800 PRO with 256MB of RAM. Granted, I know that the XTs are using DDR1 but I would think that DDR2 would have to be in mass production to be for sale on any ATI video card. Reply
    • Icewind - Wednesday, February 25, 2004 - link

      Yep, yep, I knew that DDR2 just simply wasn't going to happen anytime soon. Awesome, i'll be able to use my Corsair 3700XMS in my Athlon 64 939 pin and save some bucks.

      The message is clear, DDR2 is poo!
    • retrospooty - Wednesday, February 25, 2004 - link

      Yes, well in order to get it, you will need a new CPU, Video card, and RAM all at once. Reply

    Log in

    Don't have an account? Sign up now