In 2014 Samsung brought 3D NAND (branded as V-NAND) to the consumer SSD market with the 850 Pro and 850 EVO SATA SSDs. Based on the MLC and TLC versions respectively of Samsung's 32-layer second-generation V-NAND process, both models raised the bar for SSD performance and remain essentially unchallenged except by PCIe SSDs. The 850 EVO in particular defies the usual image of TLC SSDs as being relatively slow, power-hungry, and susceptible to problems with long-term data retention or write endurance. Most TLC drives are low-end or at best mid-range in the SATA market, but the 850 EVO for the most part competes against MLC drives in the mid to high end of the market.

Last year, the 850 Pro and EVO lines were expanded with 2TB models based on an upgraded controller with support for the larger quantities of DRAM required to keep track of so much NAND flash memory. The 2TB 850 Pro introduced a 128Gb die version of Samsung's 32-layer MLC V-NAND to replace the 86Gb die used by the smaller 850 Pros. However the 2TB 850 EVO continued to use the same 128Gb TLC V-NAND as in the smaller capacities.

Later in 2015, Samsung announced their third-generation 48-layer V-NAND process to provide 256Gb MLC and TLC parts. The plan was to switch existing products like the 850 and 950 series SSDs over to the new V-NAND beginning in early 2016 and to introduce the higher capacities it enables. The transition to the newer V-NAND has not been as quick as originally planned, but we have seen it show up in the Portable SSD T3 and the 1TB 850 EVO M.2 that has recently become available.

The 48-layer V-NAND is now coming to the 2.5" 850 EVO line in the form of a new 4TB model. It turns out that the MHX controller introduced for the 2TB models supports 4GB of DRAM, so the new 4TB 850 EVO only required changing the NAND, bumping up to a higher-capacity DRAM chip, and a firmware revision. The rest of the drive—controller, PCB, and case—are identical to the 2TB model. It is a general rule that larger SSDs tend to be faster, but as we saw when the 2TB 850s showed up, the SATA interface doesn't leave much room for improvement and the overhead of managing more flash can sometimes slightly hurt performance. It's no surprise then that the performance specifications of the 4TB model are identical to that of the 500GB, 1TB and 2TB models. The idle power consumption rating of the 4TB 850 EVO is slightly higher than the 2TB model (likely due to the increased DRAM), but the new V-NAND gives the 4TB 850 EVO substantially lower active power consumption ratings than any previous capacity.

Samsung SSD 850 EVO Specifications
Capacity 120GB 250GB 500GB 1TB (1000GB) 2TB (2000GB) 4TB (4000GB)
Controller MGX MHX
NAND Samsung 32-layer 128Gbit TLC V-NAND Samsung 48-layer 256Gbit TLC V-NAND
DRAM (LPDDR3) 256MB 512MB 1GB 2GB 4GB
Sequential Read 540MB/s
Sequential Write (max) 520MB/s
Sequential Write (non-TurboWrite) 150MB/s 300MB/s 500MB/s
4KB Random Read (QD32) 94K IOPS 97K IOPS 98K IOPS
4KB Random Write (QD32) 88K IOPS 90K IOPS
4KB Random Read (QD1) 10K IOPS
4KB Random Write (QD1) 38K IOPS 40K IOPS
DevSleep Power  2mW 2mW 2mW 4mW 5mW 10mW
Slumber Power  50mW 60mW 70mW
Active Power (Read/Write) 3.7W / 4.4W 3.7W / 4.7W 3.1W / 3.6W
Encryption AES-256, TCG Opal 2.0, IEEE-1667 (eDrive)
Endurance 75TB 150TB 300TB
Warranty Five years

The one disappointment in the specifications for the 4TB 850 EVO is the write endurance rating, still the same 300TB total as the 2TB model. A warranty that expires after only 75 drive writes is concerning even if the total bytes written quantity has been reasonable in the past. It can come across as an indication that Samsung lacks confidence in their new V-NAND, which is at odds with the 5-year warranty the drive carries. For comparison, Samsung's enterprise PM863 based on the older 32-layer TLC V-NAND has a three year warranty but a 5600TB endurance rating for its 3.84TB model. Fortunately, it appears that the write endurance rating of the 4TB 850 EVO is very conservative: the testing subjected it to a total of around 7 drive writes but the SMART lifetime indicator is down to only 99% rather than the 90 or 91% implied by the 300TBW rating.

Meanwhile thanks to TechInsights, we know a bit about what makes it possible for Samsung's third generation V-NAND to offer higher capacities that are both more power efficient and more cost-effective. In addition to raising the layer count from 32 to 48, Samsung has tweaked several aspects of the design. The NAND cells still use a charge-trap design (in contrast to the floating gate used by planar NAND flash), but with some dimensions reduced, an extra metal interconnect layer, and more compact logic and I/O regions on the die. The net effect is that density has increased from about 1.86 Gb/mm^2 for the 32-layer TLC to about 2.6 Gb/mm^2 for the 48-layer TLC in this 4TB 850 EVO.

Another trick up Samsung's sleeve is the use of F-Chips, an idea they presented at ISSCC 2015. The F-Chips serve a similar purpose to the buffers on FB-DIMMs for DRAM: rather than directly connect the SSD controller to a stack of NAND dies using a multidrop bus, the F-Chip is an interface chip that is connected to the SSD controller, and it in turn connects to two groups of four NAND dies. Because the tiny F-Chip inhabits the same BGA package as the stack of NAND and because its connections to the NAND are shared across only four chips instead of 8 or 16, maintaining signal integrity is much less of a problem. Likewise, the sharing of the bus between the NAND package and the SSD controller is reduced or eliminated.


(Source: TechInsights via EETimes)

The original intent of this development was to allow for much higher throughput between the SSD controller and the NAND so that PCIe SSDs wouldn't need an extreme number of channels, but the reduced signal integrity concerns may have also allowed for some simplification of the I/O circuitry on the NAND chips. The F-Chip still presents a toggle-mode DDR interface to the SSD controller, so it is essentially transparent and doesn't require any controller modifications.

Given how SSD capacity is related to both performance and power consumption, we generally prefer to compare drives of similar capacities. The 4TB 850 EVO doesn't leave us any good options: most consumer SSD product lines still top out around 1TB, large enterprise SAS and PCIe SSDs wouldn't be a useful point of comparison and a RAID array of several smaller SATA SSDs wouldn't quite be fair either, and I don't even have a mechanical hard drive larger than 3TB handy. For now, the 4TB 850 EVO is in a class of its own. It should be joined soon by a 4TB 850 Pro, but other than that most of the competition will only be reaching 2TB capacities this year. For this review, the 4TB 850 EVO will be compared against the other capacities of Samsung 850 EVO and 850 Pro as well as the largest of several other SSD product lines that compete more directly against the smaller capacity 850 EVOs.

With a MSRP of $1499 (37.4¢/GB) the 4TB 850 EVO should not be significantly more expensive per-GB than the 2TB model, which carries only a modest premium over the most cost-effective 500GB and 1TB capacities. The total price may be shockingly high, but per gigabyte it is not unreasonable.

AnandTech 2015 SSD Test System
CPU Intel Core i7-4770K running at 3.5GHz
(Turbo & EIST enabled, C-states disabled)
Motherboard ASUS Z97 Pro (BIOS 2701)
Chipset Intel Z97
Memory Corsair Vengeance DDR3-1866 2x8GB (9-10-9-27 2T)
Graphics Intel HD Graphics 4600
Desktop Resolution 1920 x 1200
OS Windows 8.1 x64
Performance Consistency
Comments Locked

145 Comments

View All Comments

  • jardows2 - Monday, July 11, 2016 - link

    What is the use case for this drive? $1500 for mass storage? Price per GB may be comparable to smaller drives, but that is still a huge chunk of change to get, what?

    It's a consumer drive, not an Enterprise drive. Video and Photo editors are going to hit it hard, so the lower endurance rating is going to hurt it for use in those applications. All I can see is that it is a halo product to push the industry forward, purchased only by those who have lots of spare cash to spend. Am I missing something?
  • ddriver - Monday, July 11, 2016 - link

    RAW photos, audio, video, basically any kind of data acquisition - those eat a lot of capacity. At 1500$ I'd argue this is not a consumer but a prosumer product.
  • vladx - Monday, July 11, 2016 - link

    This type of product is for people rich enough to not care about the price. Simple as that.
  • MScrip - Monday, July 11, 2016 - link

    I'd say video editing. It's not uncommon to come home with a terabyte of footage from multiple 4K cameras over multiple days of shooting. And you may be editing multiple projects at a time.

    This would make a hell of a media drive... fast and local.

    And when you're done with the projects... you move them to slower mass storage for safekeeping.
  • jardows2 - Monday, July 11, 2016 - link

    My point being, if you are a hobbyist, $1500 is a huge entry point, especially when the, albeit slow, hard drives come in a just a couple hundred dollars.

    If you are a professional, you are going to want Enterprise level drives with the endurance and warranty support. But if you are using multiple cameras shooting 4K footage, you probably have so much invested there, that $1500 for a storage drive isn't a huge percentage of the overall equipment budget. For me, I'm just using a 1080p camcorder for now, so my budget is way lower!
  • MScrip - Monday, July 11, 2016 - link

    I'm mostly 1080p... with occasional 4K. I don't need this 4TB drive... but I've got my eye on the 1TB version. Right now I'm editing on a 1TB WD Black... and its slowness shows!

    Is $1500 expensive? It depends. It's just a bigger version of the 2TB model... which is a bigger version of the 1TB model... etc.

    Drives in higher capacities always cost more money... especially the first of its kind (4TB in a single SSD)

    Asking "who is this for?" is usually a difficult question. My best guess... I'd say it's for someone who wants a single SSD... but needs to hold more than 2TB. :)
  • Impulses - Monday, July 11, 2016 - link

    Moved to 2x 1TB 850 EVOs myself a while back (with an SM951 256GB for OS/apps), can't wait until the higher capacities come down in price... Depending on how much of a premium the 4TB sustains over time I could see myself adding one (or two) 2TB or just going straight to 4TB.

    Mostly working with 1080p and relatively small 16MP RAWs... Bought the 1TB before the 2TB was readily available but I don't really regret that bit, higher seqs when going to the SM951 and easier to repurpose them later on.
  • Silh - Monday, July 11, 2016 - link

    One use case, which is admittedly niche: musicians using virtual instruments.

    Instrument sample libraries can run into the multi-gigabyte range (have ~2gb in total myself, and I'm only a hobbyist), and are built up of recordings of instruments playing single notes in various volumes, styles, etc., depending on the library's level of detail sometimes recordings of the transitions between notes.

    Less detailed virtual instruments may only eat up a few hundred MB in samples; it's not a huge deal to load the entire thing into memory for those. However, more detailed ones can run in the tens of GB's per instrument for all the different layers, and once you start building up an entire virtual orchestra, you will have to resort to loading them from the disk during playback, and for that you require something with low latency and high throughput... hence the use of SSD's. Don't even need the write endurance in a case like this, even.
  • ddriver - Monday, July 11, 2016 - link

    Nah, you really want samples loaded in RAM. RAM is cheap, even a modest DAW system will have at least 16 gigs of ram. Latency really matters here, and RAM latency is much, much lower than SSD, and sample libraries aren't that big. Sure, there are a few libraries in excess of 30 GB, but you really use a much smaller subset of the whole thing at a time.
  • Silh - Monday, July 11, 2016 - link

    It really depends on which sample libraries you're using, and some of the big ones get quite huge. The (perhaps now mere) 32gb RAM on my system only can hold so much, especially with some of the big EastWest libraries.

    The other advantage of course, is that I can load my entire template in a matter of a couple of minutes instead of waiting 15 minutes for it to load off a regular HDD.

Log in

Don't have an account? Sign up now