The initial set of Z97 reviews demonstrated that most motherboard manufacturers were implementing at least one the new storage options offered by the chipset: SATA Express and M.2.  The motherboard we are testing today, the Z97-Pro, uses both but incorporates a switching system so only one is active at the time.  Similarly to the Z97-Deluxe which we have reviewed, ASUS’ new brushed metalling gold design is here on the Z97-Pro as well.

ASUS Z97-Pro WiFi AC Overview

The birth of SATAe and M.2 in the market is a strangely complicated one. Both of these new standards, despite the lack of drives for end-users to purchase, require two of the eight lanes from the chipset in order to function, as well as two SATA 6 Gbps ports for SATA modes. One would suggest that this requires four PCIe lanes in order to incorporate both onto a product; however the current solutions we have seen show that the lane allocation is shared by both M.2 and SATAe, meaning that using one disables the other. Sharing lanes is nothing new for motherboards, where we might see a PCIe 2.0 x4 slot share lanes with controllers or PCIe 2.0 x1 slots. Compounding this fact, Intel only officially supports their storage technology on a single x2 at a time and not both, suggesting that the switch method is the only appropriate way to evolve the situation. This leaves motherboards that use both of these technologies, when the products come to market, in a precarious position. The Z97-Pro takes the brunt of this head-on, as it were. While it is impossible to implement RST on two PCIe storage ports at once, a manufacturer can use an ASMedia controller for a SATAe port, which also consumes PCIe lanes and adds cost.

The Z97-Pro aims to tackle the large landscape of motherboard offerings around the $188 region, or $200 with added 802.11ac for the WIFI AC variant. This price bracket features others such as the Z97X-SOC, Fatal1ty Z97 and Z97 Gaming 7, all of which are aimed to sell with their respective crowds.

We examined the software and BIOS offerings of the ASUS Z97 range with the Z97-Deluxe which show a continued improvement over ASUS’ generational cadence, although the BIOS aesthetic recommendations still stand. Fan controls allow every fan header on board to be controlled through DC or PWM, and the built-in BIOS fan testing system helps expedite accurate fan profiles. The EZ OC mode in the BIOS also gives users a more targeted look at automatic overclocks. The software has a new trick in Turbo App, giving users overclock granularity on a per-program basis, as well as new overclocking options for stress testing.

Performance of the Z97-Pro shines out via the onboard audio (an enhanced Realtek ALC1150 solution with PCB separation, filter caps and DTS support) and Z97's excellent DPC Latency, however our early pre-release BIOS had a long POST time, suggesting that users should update the BIOS ASAP in case this has changed. Power consumption was a little higher than expected, but still in reasonable limits. USB 2.0 speed was boosted by the in-built Turbo mode, giving a sub 40-second result.

The Z97-Pro offers a WiFi version using a 2T2R 802.11ac WiFi module, situated on the rear IO. I am a big fan of integrated WiFi solutions on the rear IO rather, but the original increase in price for the version with the module was $30 might seem a little high. However, now the difference is $12 and given that the WiFi module is unavailable as a separate purchase, users with WiFi needs (such as myself who tests machines in a different room with no wired Ethernet access) should consider the WiFi version because even at $200 the system seems to punch above its weight. Normally when I review a system I keep a list of oddities, issues, irregularities or interesting tidbits of information as I test in order to help shape the review. With the Z97-Pro, my list contained a total of zero entries, indicating that it just worked as it said it should. This is sometimes an oddly rare occurrence in a mature industry.

ASUS Z97-Pro Visual Inspection

The brushed metallic look we saw with the Z97-Deluxe is here on the Z97-Pro as well, as shown on the two power delivery heatsinks and the new styled circular chipset heatsink. I hate to use artsy words to describe a motherboard, but I feel like I want to use the word ‘contemporary’, whatever that means. The ASUSDESIGN logo adorns one of the heatsinks, and the rest of the motherboard attempts to use two shades of black for the rest of the ports and slots. The switches and rear IO keep their silvery look.

The socket area is bounded on two sides of the minimum Intel specifications by power delivery chokes and on a third side by the DRAM slots. As with most motherboards in this segment, the heatsinks are designed to allow large coolers, however due to the close proximity of the DRAM slots, users with taller memory might have to rely on slightly smaller CPU coolers in order to fit a full set of memory.

In the socket area the user has access to four fan headers: one to the bottom left below the power delivery heatsink, the two CPU headers between the top heatsink and the DRAM, and a final header just above the 24-pin ATX power connector. At a stretch there is a fifth within reach of the socket, just below the 24-pin, while the sixth and final fan header is at the bottom of the motherboard.

The DRAM slots are color coordinated for the two memory channels, and all four slots use a single sided latch mechanism for easier memory removal. With this system users should be aware that installing memory requires a double check to make sure it is seated in the slot correctly.

At the top right of the motherboard is the MemOK button, used to recover memory settings from a failed overclock without losing the rest of the BIOS settings in the process. Below this is the EZ XMP switch, a new addition for Z97 that allows users to enable XMP at the touch of a button and without entering BIOS. Given the number of enthusiast users, especially (anecdotally) at LAN events, who have super machines but fail to run at XMP, this is a nice option to have.

The SATA ports are arranged such that the SATA Express port is nearest the 24-pin ATX, followed by four chipset SATA 6 Gbps ports and two SATA 6 Gbps from the ASMedia controller. Given what we have seen from GIGABYTE and ASRock, I am a little perplexed as to why ASUS did not invest into the tiered/stacked SATA plastic housing and routed appropriately, as this would have saved some space for (perhaps) another SATA controller or something else (a USB port?). Beside the chipset SATA 6 Gbps ports is the M.2 x2 slot, which as mentioned above shares bandwidth with the SATAe ports such that only one can be used at a time.

Along the bottom of the motherboard we have the T_Sensor that allows users to equip their own thermocouple and adjust the fan speeds on the motherboard based on the output of the thermocouple. Next to this is the DirectKey header that allows the user to enter the BIOS on the next boot. This feature used to be an onboard button, which I prefer, but has been relegated to jumper duty. Above these two jumpers are the TPU and EPU switches, providing automatic overclocks and power saving modes respectively. Beneath these, right at the bottom of the board, is the front panel header, one of the aforementioned fan headers and two USB headers.

Moving left across the bottom of the motherboard we have our second chipset based USB 3.0 header, a TPM module header, the BIOS Flashback button, a power button, the Thunderbolt header and the front audio header. Above the TPM header, and just above the PCIe slot in this place, is the two-digit Debug display. This position between the PCIe slots is a little different to what we usually encounter, and in this position it would be blocked by a second GPU.

The PCIe slots are arranged in a typical fashion, with an x1 at the top followed by x16, x1, x1, x8, x1 and an x4. When a device is placed in the x8 slot, the x16 will reduce down to x8 to compensate. The two PCIe 2.0 x1 slots in the middle actually share bandwidth, with the bottom of the two enabled by default. The PCIe 2.0 x4 actually shares bandwidth with two other parts of the motherboard – the two chipset USB 3.0 ports on the rear IO, and the final PCIe 2.0 x1 slot. By default the PCIe 2.0 x4 slot is in x1 mode, and the USB 3.0 ports/PCIe x1_4 slot are both enabled. In x2 mode, the PCIe x1_4 slot is disabled, and in x4 mode both the PCIe x1_4 and USB3_E12 are disabled.

The audio on the Z97-Pro is an enhanced version of the Realtek ALC1150 audio codec featuring PCB separation, separate PCB layers for left/right signaling, an EM shield, additional filter caps, a headphone amplifier, DTS support and a de-pop circuit.

The rear IO of the motherboard gives a combination PS/2 port, two USB 2.0 ports, four USB 3.0 ports, the four standard video outputs, gigabit Ethernet (Intel I218-V) and audio jacks. Normally I prefer more than two USB 2.0 ports for installing an operating system via USB (ideally need three in case USB 3.0 are not initialized), however there was no issue here. One might argue that having all four video outputs on the rear is redundant given the targeted use of this motherboard is towards PCIe users, and some part of me is wondering if dual HDMI+DisplayPort or dual mDP + HDMI/DVI-D is more a preferred option going forward. The gap in the rear IO shown above is where the WiFi Go module should sit.

Board Features

ASUS Z97-Pro (WiFi AC)
Price US (Newegg)
Size ATX
CPU Interface LGA-1150
Chipset Intel Z97
Memory Slots Four DDR3 DIMM slots supporting up to 32 GB
Up to Dual Channel, 1333-3200 MHz
Video Outputs VGA (1920x1200 at 60 Hz)
DVI-D (1920x1200 at 60Hz)
HDMI (4096x2160 at 24 Hz or 2560x1600 at 60 Hz)
DisplayPort (4096x2160 at 24 Hz or 3840x2160 at 60 Hz)
Onboard LAN Intel I218-V
Broadcom 802.11ac 2T2R
Onboard Audio Realtek ALC1150 (DTS)
Expansion Slots 2 x PCIe 3.0 x16 (x16 or x8/x8)
1 x PCIe 2.0 x4 (Shares bandwidth with USB3_E12 and PCIe x1_4)
4 x PCIe 2.0 x1 (PCIe x1_2 shares bandwidth with PCIe x1_3)
Onboard SATA/RAID 6 x SATA 6 Gbps (PCH) (two shared with SATAe)
2 x SATA 6 Gbps (ASMedia)
1 x SATAe x2 (PCH) (shared x2 and SATA with M.2)
1 x M.2 x2 (PCH, SATA and PCIe) (shared x2 and SATA with SATAe)
USB 3.0 6 x USB 3.0 (PCH) (2 back panel, 2 headers)
2 x USB 3.0 (ASMedia) (2 back panel)
Onboard 8 x SATA 6 Gbps
1 x SATAe
1 x M.2
2 x USB 3.0 Headers
2 x USB 2.0 Headers
1 x TPM Header
6 x Fan Headers
1 x TB Header
EZ XMP Switch
DirectKey Button
MemOK Button
TPU Switch
EPU Switch
USB BIOS Flashback Button
Front Panel Header
Front Audio Header
Two Digit Debug
Power Button
Power Connectors 1 x 24-pin ATX
1 x 8-pin CPU
Fan Headers 1 x CPU (4-pin, DC+PWM)
1 x CPU_OPT (4-pin, DC+PWM)
4 x CHA (4-pin, DC+PWM)
IO Panel 1 x PS/2 Combination Port
VGA
DVI-D
HDMI
DisplayPort
1 x Intel I218-V NIC
4 x USB 3.0
2 x USB 2.0
WiFi Go! Module
Audio Jacks
Warranty Period 3 Years
Product Page Link

 

ASUS Z97-Pro WiFi AC BIOS and Software
POST A COMMENT

36 Comments

View All Comments

  • Samus - Wednesday, July 16, 2014 - link

    I'm running a system based on the Asus Z97I-Plus (ITX) with a i5-4690K @ 4.5GHz 1.3v its been rock solid for the month I've had it.

    Coming from an Asus H81I ITX i5-4670K @ 4.2GHz. There are some mild BIOS improvements but the addition of M2 on the Z97I was what got me. That, and my H81 wouldn't run the Haswell refresh (chipset was old version) so I was pretty much locked into Haswell with no Broadwell/Skylake options for the future.
    Reply
  • mapesdhs - Saturday, July 19, 2014 - link


    Sounds good! I'm curious though, how are you cooling your 4690K? I've been pondering
    whether a K CPU with a moderate oc is viable given I want minimum noise (for the HTPC
    build that is).

    Ian.
    Reply
  • p1esk - Wednesday, July 16, 2014 - link

    How could 2x580 be possibly quicker than Titan Black? It's 2x512 cores vs 2,880 cores at higher clock, and Titan has twice memory bandwidth. Reply
  • ZeDestructor - Thursday, July 17, 2014 - link

    The cores perform differently. Similar to how clock for clock Haswell is faster than IVB. In this case, the 580 has more powerful, but slower and hotter cores than the titan black.

    By the looks of it, the blender code isn't memory bound either, which explains why it makes do with the lower bandwidth.
    Reply
  • mapesdhs - Saturday, July 19, 2014 - link


    As ZeDestructor says, the shader structure is very different in the 500 series, but to
    clarify: after the 500 series, NVIDIA halved the shader clock speeds in order to make
    power delivery & heat easier to deal with, but this means a lot more shaders are
    required to give the same performance (almost 3X as many), eg. I've tested a K5000
    which has 3X more shaders, but it's slower than a 580 for CUDA. This is why, for CUDA
    tasks, a 580 beats all of the 600 series and most of the 700 series. Also, the 580 has a
    lot of bandwidth, so the available bandwidth per core is very high compared to later
    designs; this can make a difference in some cases.

    See the following (for the Arion test, my system is no. 18 in the table; also note the table
    has a typo, system 15 is a triple-780):

    http://www.randomcontrol.com/arionbench
    http://www.tomshardware.co.uk/forum/id-2173987/gig...
    http://forums.creativecow.net/thread/2/1019120

    A Titan Black does the Blender BMW/Cycles test in 24 seconds. My quad-580 system does
    it in 11.56 seconds.

    Summary: for CUDA, two 580s are quicker than a Titan, making them a good budget option
    for AE users, etc., though of course it makes sense if possible to obtain 3GB models.

    For 3D gaming though, the situation is completely different. Likewise, a CUDA task
    requiring mostly FP64 would be better with Titans.

    Ian.
    Reply
  • FriendlyUser - Wednesday, July 16, 2014 - link

    I particularly appreciate the Intel 218V Lan. An excellent choice. Together with the decent onboard audio, you really get some premium hardware for your money. I don't particularly care for the Wi-Fi AC controller, though. These things change so fast, I'd rather have an expansion card (for example, the 802.11ac spec could theoretically scale up to several Gbs). Plus, I prefer getting WiFi equipment from the same vendor, to simplify installation and interoperability. Reply
  • DanNeely - Wednesday, July 16, 2014 - link

    I'm ambivalent about the wifi, since I'd only ever use it as a temporary backup option.

    What annoys me a bit is that it looks like the connector is a PCIe 1x slot that was moved closer to the back edge of the board. If they wanted to play fast and loose with the standard to get wifi out in the IO port area instead of the expansion card area; if they'd put the adapter where the audio out is and at the standard distance from the edge it would be possible to kludge an off the shelf card in as an upgrade by removing it's bracket and either removing the IO shield or trimming it out with a cutting tool.
    Reply
  • ZeDestructor - Thursday, July 17, 2014 - link

    What's even more annoying is that they're not using a standard miniPCIe or M.2 wifi card instead with some internal U.Fl to RP-SMA coax cabling from somewhere else (right behind the PCIe 1x slots comes to mind) on the board.

    Btw, it seems thay are using something that's more than PCIe x1 but less than PCIe x4.. nice and proprietary.
    Reply
  • Antronman - Wednesday, July 16, 2014 - link

    Not even Asus' top end, and it already blows away the competition... Reply
  • Samus - Wednesday, July 16, 2014 - link

    Yeah I'm surprised what a value it actually is. Sub-$200 and you get Intel Gigabit, Xonar-class audio, M.2, VRM heatsinks and all the typical Z97 stuff. I also like the 90-series motherboard color schemes. They're actually reminiscent of ASRock's. The 80-series Asus boards had a weird color combo (yellow DIMM slots, for example) but ASRock had this Black/Gold theme.

    And I don't care what people say, I've had Asus boards since the i486 days and every single one has been incredibly solid.
    Reply

Log in

Don't have an account? Sign up now