Seeing the Future: DisplayPort 1.2

While Barts doesn’t bring a massive overhaul to AMD’s core architecture, it’s a different story for all of the secondary controllers contained within Barts. Compared to Cypress, practically everything involving displays and video decoding has been refreshed, replaced, or overhauled, making these feature upgrades the defining change for the 6800 series.

We’ll start on the display side with DisplayPort. AMD has been a major backer of DisplayPort since it was created in 2006, and in 2009 they went as far as making DisplayPort part of their standard port configuration for most of the 5000 series cards. Furthermore for AMD DisplayPort goes hand-in-hand with their Eyefinity initiative, as AMD relies on the fact that DisplayPort doesn’t require an independent clock generator for each monitor in order to efficiently drive 6 monitors from a single card.

So with AMD’s investment in DisplayPort it should come as no surprise that they’re already ready with support for the next version of DisplayPort, less than a year after the specification was finalized. The Radeon HD 6800 series will be the first products anywhere shipping with DP1.2 support – in fact AMD can’t even call it DP1.2 Compliant because the other devices needed for compliance testing aren’t available yet. Instead they’re calling it DP1.2 Ready for the time being.

So what does DP1.2 bring to the table? On a technical level, the only major change is that DP1.2 doubles DP1.1’s bandwidth, from 10.8Gbps (8.64Gbps video) to 21.6Gbps (17.28Gbps video); or to put this in DVI terms DP1.2 will have roughly twice as much video bandwidth as a dual-link DVI port. It’s by doubling DisplayPort’s bandwidth, along with defining new standards, that enable DP1.2’s new features.

At the moment the feature AMD is touting the most with DP1.2 is its ability to drive multiple monitors from a single port, which relates directly to AMD’s Eyefinity technology. DP1.2’s bandwidth upgrade means that it has more than enough bandwidth to drive even the largest consumer monitor; more specifically a single DP1.2 link has enough bandwidth to drive 2 2560 monitors or 4 1920 monitors at 60Hz. Furthermore because DisplayPort is a packet-based transmission medium, it’s easy to expand its feature set since devices only need to know how to handle packets addressed to them. For these reasons multiple display support was canonized in to the DP1.2 standard under the name Multi-Stream Transport (MST).

MST, as the name implies, takes advantage of DP1.2’s bandwidth and packetized nature by interleaving several display streams in to a single DP1.2 stream, with a completely unique display stream for each monitor. Meanwhile on the receiving end there are two ways to handle MST: daisy-chaining and hubs. Daisy-chaining is rather self-explanatory, with one DP1.2 monitor plugged in to the next one to pass along the signal to each successive monitor. In practice we don’t expect to see daisy-chaining used much except on prefabricated multi-monitor setups, as daisy-chaining requires DP1.2 monitors and can be clumsy to setup.

The alternative method is to use a DP1.2 MST hub. A MST hub splits up the signal between client devices, and in spite of what the name “hub” may imply a MST hub is actually a smart device – it’s closer to a USB hub in that it’s actively processing signals than it is an Ethernet hub that blindly passes things along. The importance of this distinction is that the MST hub does away with the need to have a DP1.2 compliant monitor, as the hub is taking care of separating the display streams and communicating to the host via DP1.2. Furthermore MST hubs are compatible with adaptors, meaning DVI/VGA/HDMI ports can be created off of a MST hub by using the appropriate active adaptor. At the end of the day the MST hub is how AMD and other manufacturers are going to drive multiple displays from devices that don’t have the space for multiple outputs.

For Barts AMD is keeping parity with Cypress’s display controller, giving Barts the ability to drive up to 6 monitors. Unlike Cypress however, the existence of MST hubs mean that AMD doesn’t need to dedicate all the space on a card’s bracket to mini-DP outputs, instead AMD is using 2 mini-DP ports to drive 6 monitors in a 3+3 configuration. This in turn means the Eyefinity6 line as we know it is rendered redundant, as AMD & partners no longer need to produce separate E6 cards now that every Barts card can drive 6 DP monitors. Thus as far as AMD’s Eyefinity initiative is concerned it just became a lot more practical to do a 6 monitor Eyefinity setup on a single card, performance notwithstanding.

For the moment the catch is that AMD is the first company to market with a product supporting DP1.2, putting the company in a chicken & egg position with AMD serving as the chicken. MST hubs and DP1.2 displays aren’t expected to be available until early 2011 (hint: look for them at CES) which means it’s going to be a bit longer before the rest of the hardware ecosystem catches up to what AMD can do with Barts.

Besides MST, DP1.2’s bandwidth has three other uses for AMD: higher resolutions/bitdepths, bitstreaming audio, and 3D stereoscopy. As DP1.1’s video bandwidth was only comparable to DL-DVI, the monitor limits were similar: 2560x2048@60Hz with 24bit color. With double the bandwidth for DP1.2, AMD can now drive larger and/or higher bitdepth monitors over DP; 4096x2160@50Hz for the largest monitors, and a number of lower resolutions with 30bit color. When talking to AMD Senior Fellow and company DisplayPort guru David Glen, higher color depths in particular came up a number of times. Although David isn’t necessarily speaking for AMD here, it’s his belief that we’re going to see color depths become important in the consumer space over the next several years as companies look to add new features and functionality to their monitors. And it’s DisplayPort that he wants to use to deliver that functionality.

Along with higher color depths at higher resolutions, DP1.2 also improves on the quality of the audio passed along by DP. DP1.1 was capable of passing along multichannel LPCM audio, but it only had 6.144Mbps available for audio, which ruled out multichannel audio at high bitrates (e.g. 8 channel LPCM 192Khz/24bit) or even compressed lossless audio. With DP1.2 the audio channel has been increased to 48Mbps, giving DP enough bandwidth for unrestricted LPCM along with support for Dolby and DTS lossless audio formats. This brings it up to par with HDMI, which has been able to support these features since 1.3.

Finally, much like how DP1.2 goes hand-in-hand with AMD’s Eyefinity initiative, it also goes hand-in-hand with the company’s new 3D stereoscopy initiative, HD3D. We’ll cover HD3D in depth later, but for now we’ll touch on how it relates to DP1.2. With DP1.2’s additional bandwidth it now has more bandwidth than either HDMI1.4a or DL-DVI, which AMD believes is crucial to enabling better 3D experiences. Case in point, for 3D HDMI 1.4a maxes out at 1080p24 (48Hz total), which is enough for a full resolution movie in 3D but isn’t enough for live action video or 3D gaming, both of which require 120Hz in order to achieve 60Hz in each eye. DP1.2 on the other hand could drive 2560x1600 @ 120Hz, giving 60Hz to each eye at resolutions above full HD.

Ultimately this blurs the line between HDMI and DisplayPort and whether they’re complimentary or competitive interfaces, but you can see where this is going. The most immediate benefit would be that this would make it possible to play Blu-Ray 3D in a window, as it currently has to be played in full screen mode when using HDMI 1.4a in order to make use of 1080p24.

In the meantime however the biggest holdup is still going to be adoption. Support for DisplayPort is steadily improving with most Dell and HP monitors now supporting DisplayPort, but a number of other parties still do not support it, particular among the cheap TN monitors that crowd the market these days. AMD’s DisplayPort ambitions are still reliant on more display manufacturers including DP support on all of their monitors, and retailers like Newegg and Best Buy making it easier to find and identify monitors with DP support. CES 2011 should give us a good indication on how much support there is for DP on the display side of things, as display manufacturers will be showing off their latest wares.

Barts: The Next Evolution of Cypress Seeing the Present: HDMI 1.4a, UVD3, and Display Correction
POST A COMMENT

197 Comments

View All Comments

  • Ryan Smith - Friday, October 22, 2010 - link

    In case it isn't obvious from the slipshod organization of the article, we didn't quite get it done on time. We had less than a week to put this article together when normally for an article of this size it takes 2 weeks. Check back in the morning, everything on Eyefinity, DP1.2, etc will be up by then. Reply
  • counter03 - Friday, October 22, 2010 - link

    i am quite interested in that 'mst hub'.is there any available product now?well,i just find nothing with google. Reply
  • wolrah - Friday, October 22, 2010 - link

    The card still has two TMDS clock generators. This means only two DVI/HDMI displays can be driven off the card at one time, no matter what connection. With that in mind, I wouldn't be surprised if the card doesn't even support passive adapters as there is literally no good reason to ever use them. You already have two native ports, so with a maximum of two DVI displays that's that.

    Regardless of if passive adapters are supported, you'll still need active adapters or native DisplayPort on your display to run three or four monitors off this card.

    Supposedly it also supports DisplayPort daisy chaining, so possibly when monitors arrive that have an out port it may handle more than four displays, but again only a maximum of two can be DVI/HDMI without active adapters.
    Reply
  • ninjaquick - Monday, October 25, 2010 - link

    DP support shouldn't be a problem since I've seen quite a few monitors coming out with DP in and some with I/O. Reply
  • Abot13 - Saturday, October 23, 2010 - link

    With the 6800 series the cards can support up to 6 monitors in Eyefinity. The DP ports can use a DP hub or the monitors can be chained with DP. Either way the max is 6 monitors per card. Reply
  • ol1bit - Thursday, October 21, 2010 - link

    The naming stinks, but I can see how these cards will be a big Christmas season for AMD.

    So people that don't the new naming scheme will rush out an buy the bigger names. Smooth Marketing Move.

    Well, if the 6900's launch next month, that will be fun to see.
    Reply
  • Zokudu - Thursday, October 21, 2010 - link

    You removed Left 4 Dead from your benchmarks. Does this mean you won't be replacing it with another Source game (ie L4D2 or maybe Portal 2 when that releases)?

    I know its not 100% perfect but 3 of the top 10 selling games on steam right now are run on the Source engine and the only other ones that share and engine are BF:BC2 and MoH both using Frostbite. I would think that having some form of a Source game in there would be a good idea considering the vast amount of popular games that run on it. I always used the L4D benchmark to compare performance for TF2 and CS:S. in the past.

    Otherwise good review and I'm excited for the HD6900 launch next month.
    Reply
  • Ryan Smith - Friday, October 22, 2010 - link

    By the time Portal 2 comes out, it'll be about the time we refresh our suite anyhow. For the time being the existing Source games run on anything (even the GT 430 got L4D playable at 1680 with 4xAA) so it's not a useful benchmark, especially since there's no guarantee Portal will run that well. Reply
  • AmdInside - Thursday, October 21, 2010 - link

    In the 3DTV Play article, you mentioned AMD's 6000 series would challenge NVIDIA in 3D with the 6000 series but I didn't read any info on it in this article. What gives? Reply
  • StevoLincolnite - Friday, October 22, 2010 - link

    Also didn't see any mention of the improved crossfire performance either... Reply

Log in

Don't have an account? Sign up now