In case you haven’t noticed, the iPhone 4’s antenna design has come under considerable scrutiny. In our iPhone 4 review, we investigated the iPhone 4 antenna and came to two conclusions. First, that iOS 4 was displaying signal bars in an overly optimistic manner, compressing the dynamic range of possible signal bars users can see. Second, we identified a worst case signal drop of around 24 dB when the iPhone 4 is cupped tightly in the left hand, covering the black strip and possibly detuning the antennas and adding additional attenuation from the presence of the hand.

Since those initial measurements, we’ve been working tirelessly to both characterize the problem, fully understand the mechanisms behind it, and report on a number of possible solutions.

The Bars Have Changed

On July 2, Apple released a letter noting that the formula used in iOS 4.0 to calculate how many bars are presented for each signal strength is “totally wrong.” This mirrored our conclusions that the effects of the signal drop were exacerbated in part by the way the iPhone visualizes signal strength - the dynamic range is compressed so much that the 24 dB drop from cupping the phone without a case could make all the bars go away.

They went on to promise that in a future software update they would make bars 1, 2, and 3 taller, and make the bars more “accurate” by displaying 2 bars fewer in certain circumstances.

iOS 4.1 beta rolled around yesterday, and we immediately dove in to find out just how much the bar to signal strength mapping has changed. Update: iOS 4.0.1 final just came out this afternoon and we finished preliminary testing. The signal strength mapping algorithms are identical to the 4.1 beta. The findings in this article apply to 4.0.1 as well as the 4.1 beta.

After updating our devices to the iOS 4.1 beta (and 4.0.1) and making sure our little trick to show signal strength in dBm instead of bars still worked, we set off. Remember last time how I said I drove around town all day with iOS 4.0, testing the phone, and recording signal strength and how many bars were being shown? You guessed it - another update, another evening of driving around. Anand and I did quite our fair share of moving around to get a complete picture of what the new cutoffs are.


Old Bars


New Bars

The results are conclusive - Apple has dramatically changed the signal strength to signal bar mapping in iOS 4.0.1 and the iOS 4.1 beta, making the dynamic range not only much broader, but the range values for each bar much wider. The range of signals that correspond to bars three and four are the same width, and bar two is only slightly less.

The cutoff value for two bars to one bar remains the same, but every other value has increased. The result is that the worst case drop of 24 dBm no longer makes all the signal bars disappear, but rather two.

AnandTech reader Mike Escoffery, Director of Design and User Experience at Media Platforms, created his own diagram to help compare the old and new way of iOS signal strength reporting:

As you can see the old way (top) put far too much weight into the 5th bar of signal. Apple's new approach not only splits it up more reasonably between the 4th and 5th bar (still non-linearly keeping you in the 5th bar if possible) but also extends the range of the lower bars.

This change actually presented itself in our numeric signal strength reports - there’s more dynamic range in these numbers too. Previously, the absolute lowest value any iPhone would report was -113 dBm. With iOS 4.0.1/4.1, the value is now a shockingly low -121 dBm. In the iPhone 4 review, I talked a lot about how although the phone is prone to dropping signal from being held wrong, it was measurably more sensitive in weak signal areas. I was shocked that calls and data worked seemingly unfazed at -113 dBm. It seems as though this increased 8 dBm of range below -113 dBm was meant to show really how much more sensitive the radio stack is - it undeniably is more sensitive. Both Anand and I were able to hang onto calls all the way down at -121 dBm.

We’ve also included a comparison to how the latest version of Android displays signal bars from GSM or UMTS networks below. Thankfully, this didn’t require driving around town all day but rather inspecting the latest version of the Android source code from Google’s own repositories. Android uses an ASU value to compute signal strength, which isn’t anything more than a remapping of dBm to a sane value that’s a bit easier to interpret.

Apple’s mappings have gone from having probably the most compressed dynamic range among handset vendors to less compressed than Android.

While the software update obviously does not and cannot address the design of the antenna itself - or make the drop from holding the phone any less - it does change the way the issue is perceived among users. The result is that most iPhone users will see fewer bars disappear when they hold the iPhone 4 in a bare hand. The side effect is that the iPhone now displays fewer bars in most places, and users that haven’t been reporting signal in dBm will time see the - perhaps a bit shocking - reality of locations previously denoted as having excellent signal.

Interestingly enough, Apple has indeed changed the heights of bars 1, 2, and 3. They’re taller, and the result is that the relative heights are no longer linear, but rather a tad exponential looking. It’s a mind trick that Apple no doubt hopes will make the signal look better. If the bars are taller, they must denote stronger signal, right?


From top to bottom: iOS 4.1, iOS 4.0, Android 2.2

The reality is that Apple likely wants to deflect at least some of the initial backlash AT&T will face for reporting the signal bars without any concessions. Concessions that used to make coverage look better than it really is. Regardless of how tall the bars are, there are still going to be fewer of them virtually everywhere. Interestingly enough, while bars 1 and 2 are the most changed, their respective cutoffs are virtually unchanged.

While I was testing iOS 4.0.1, I told Anand that the signal reporting lie that started with the iPhone 3G had been removed entirely. That iOS 4.0.1 would potentially show the reality of AT&T’s coverage to iPhone users. With 4.0.1 users looking at signal bars will get a much more realistic view of how signal is changing. 

We tested the iOS 4.1 beta on iPhone 3GSes as well, and found the mappings to be the same there as well.

Better at the Low End, Mixed Feelings Everywhere Else
POST A COMMENT

149 Comments

View All Comments

  • geogaddi - Friday, July 16, 2010 - link

    ...and they give us: bumper cases! Reply
  • Gorked - Thursday, July 15, 2010 - link

    Thank you for another outstanding article.

    My wife is frustrated because I told her to hold off on upgrading the phone to find out what Apple is going to do but it is always nice to send her your articles so she knows where I am coming from.
    Reply
  • FATCamaro - Thursday, July 15, 2010 - link

    Considering 90% of the people aren't having problems.... Reply
  • fitten - Thursday, July 15, 2010 - link

    [citation needed] Reply
  • rs1 - Thursday, July 15, 2010 - link

    And even if it's accurate, a 10% failure rate is huge. Toyota recalled an entire fleet of vehicles over a bug that affected less than 1% of them. Saying that 90% of people don't have problems misses the point entirely.

    A product that doesn't function properly 10% of the time is unreliable, and manufacturers need to be held accountable when they sell an unreliable product to people.
    Reply
  • Snotling - Thursday, July 15, 2010 - link

    on the other hand, a phone dropping calls is less of a safety hazard than a car with a stuck gas pedal.

    not to say that its not anoying and obviously a flaw in the manufacturing or design.
    Reply
  • rs1 - Thursday, July 15, 2010 - link

    True, although sooner or later I'm sure this issue will cause a call to drop in an emergency situation. For instance, if someone has called 911 and the operator is about to give them instructions on how to perform CPR or whatever. It's not as overtly hazardous, but it can still be dangerous under the right circumstances. Reply
  • progr - Thursday, July 15, 2010 - link

    You can't be serious. It's like saying that a company that make bikes (with semi-broken bumpers on 10% of products shipped) must recall the entire fleet of bikes cause, sooner or later, you will find a pregnant woman down the road and you can't take her to the hospital in time. Reply
  • SunSamurai - Friday, July 16, 2010 - link

    That is about the most retarded thing ever. Lets hold Apple responsible for every 911 call that was dropped due to ATT shitty network.

    THE iPHONE KILLS!
    Reply
  • Fri13 - Sunday, July 18, 2010 - link

    Apple told that return rate have been 1.7% from AT&T. And un-happy customers were only 0.55% who had issues with antenna or anything related to it.

    Is that bad? If iPhone 3Gs had 6% return rate the 1.7% (AT&T) is not much at all. Only 1/3 of it and over 3 million already sold. And even that media is triumphing all days, iPhone gets sold out.
    Reply

Log in

Don't have an account? Sign up now