The Crucial MX300 750GB SSD Review: Micron's 3D NAND Arrives

Micron is the second company to the 3D NAND flash milestone, with today's release of the Crucial MX300 750GB Limited Edition. This follows on from two years ago when Samsung became the first manufacturer to ship SSDs with 3D NAND flash, the 850 Pro - a drive launched as a flagship high end drive and remains the fastest consumer SATA drive today. By contrast, the Crucial MX300 is intended to be a mainstream affordable SSD based on 3D TLC NAND, making the MX300 more of a direct competitor to the 850 Evo.

Micron's strategy for transitioning to 3D NAND is quite different from the path that Samsung took. Similar to other projects, Micron is once more partnered with Intel to produce this generation of flash memory, and their 3D NAND is different compared to Samsung in several ways. While the rest of the industry chose to combine the 3D NAND transition with a switch from a floating gate memory cell to a charge trap design, Intel and Micron's 3D NAND is still a floating gate design, making the end-point a 'simpler' two-step process. As a result, the capacity is also quite different: Samsung's 3D NAND debuted with a 32-layer but small 86Gb MLC die and 128Gb TLC, later followed up with a 128Gb MLC, whereas the Intel/Micron first effort on 32-layer 3D NAND is an MLC part with a capacity of 256Gb and a TLC part with 384Gb, making for a much larger die. While Samsung has continued to develop planar NAND alongside their 3D NAND and recently reintroduced planar NAND to their retail SSD family with the 750 EVO, Micron is committed to going all-3D with new products. To be clear however, Micron's existing planar NAND products won't be going away quickly (especially in the enterprise market).

The Crucial MX300 750GB

The MX300 was first made official at a Micron enterprise storage event with a release planned for April/early Q2. While the launch of the full range of drives was pushed back to allow for a new firmware revision with improved performance to go through a QA cycle, Micron is sticking with the original plan of first launching a limited edition single 750GB capacity, with the full range of capacities and M.2 versions to fill in over the rest of the year. With seven extra weeks of firmware work behind them, supplies of the 750GB MX300 may not be as limited as they would have been for an April launch, but availability could be temporarily constrained as the drives with the updated firmware make their way through the supply chain. Despite this, we also expect that a tight supply of the 3D TLC was a contributing factor in a staggered release, and as a result we start with the Limited Edition first.

750GB is not a typical capacity for a SSD, but the 384Gb (48GB) die capacity of Micron's 3D TLC makes it hard to hit the usual power of two drive capacity points without having a much larger overprovisioning ratio than is typical of a consumer drive. Instead, the MX300 line will probably be the first time we see TLC clearly resulting in an increase of capacity relative to MLC drives across the full range of products, rather than just offering a lower price per GB (and one extra capacity at the high end). Micron hasn't nailed down the final specifications for the other capacities of MX300, but we do know that the smallest drive will use six dies. This will give it a raw capacity of 288GB and the usable capacity may be around 275GB rather than something in the 240-256GB range. The largest (and last to launch) capacity will be in the neighborhood of 2TB. The 750GB model uses sixteen dies arranged in eight packages of two dies each for a raw capacity of 768GB.

In the past, when NAND transitions to a smaller lithography node and a larger die capacity, the reduction in die count has caused a decrease in available parallelism and thus lower performance for drives of the same capacity. Micron is offsetting this by partitioning their 3D NAND into a four plane design, where 128Gb planar flash chips are at most two plane designs. This allows for almost as many commands to be processed simultaneously by the 3D TLC, but will also lead to somewhat higher contention on the link between the controller and the flash.

Aside from adopting 3D TLC and upgrading to the latest in Marvell's long line of SATA SSD controllers, the MX300 offers all the usual features of the MX series: encryption support, SLC caching, partial power loss protection and a three year warranty. Performance and endurance specifications are down slightly from the MX200 due to the new hardware, but are still fine for a mainstream SATA SSD. The final decisions about overprovisioning for the other capacity models could mean they will have better endurance ratings than the MX200 of comparable capacity.

From the exterior the MX300 appears virtually identical to a MX200. Opening it up to look at the PCB, we see a full size circuit board with plenty of room for more NAND, but Micron won't actually need more than the 8 packages in this drive for even the largest 2TB class model. This 750GB drive stacks just two dies per package; a 2TB class drive would need at most six dies per package, but stacking 8 or 16 dies per package is common when dealing with smaller NAND chips and especially smaller form factors. The pads for the power loss protection capacitors are almost all populated.

The 750GB Crucial MX300 comes with a MSRP of $199.99. On a price per GB basis, this puts it on par with the current actual retail prices for the MX200 and we expect competition can drive the MX300 price down further. It will probably take up position near the top of the budget planar TLC segment of the market and be cheaper than all but the best sale prices on MLC drives. So while at first glance the MX300 might appear to be the natural match against the 850 EVO, Micron is clearly aiming lower in price.

In addition to the Crucial MX200 and 3D TLC based 850 EVO, the MX300 will compete against the top performing planar TLC drives like the SanDisk X400, which is based on the same Marvell 88SS1074 controller used in the MX300.

• Thanks to Intel for the Core i7-4770K CPU
• Thanks to ASUS for the Z97 Deluxe motherboard
• Thanks to Corsair for the Vengeance 16GB DDR3-1866 DRAM kit, RM750 power supply, Carbide 200R case, and Hydro H60 CPU cooler